• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.3
• /
• pp.54-61
• /
• 2003

$SnO_2$ gas sensor for the detection DMMP, simulant of nerve gas was fabricated and its characteristics were examined. Sensing materials were $SnO_2$ added by TEX>$\alpha$-$Al_{2}O_{3}$ with 0∼20wt.% and $In_{2}O_{3}$ with 0∼3wt.% and were physically mixed each material. They were deposited by screen printing method on alumina substrate. The sensor was consisted of sensing electrode with interdigit(IDT) type in front and a heater in back side. Its dimension was 7$\times$10$\times$0.6$\textrm{mm}^2$. Crystallite size 8t phase identification, specific surface area and morphology of fabricated $SnO_2$ powders were analyzed by X-ray diffraction(XRD), surface area analyzer(BET) and by a scanning electron microscope(SEM), respectively. Sensor was measured as flow type and sensor resistance change was monitored as real time using LabVIEW program. The best sensitivities were 75% at adding 4wt.% TEX>$\alpha$-$Al_{2}O_{3}$, operating temperature $300^{\circ}C$ and 87% at adding 2wt.% $In_{2}O_{3}$, operating temperature $350^{\circ}C$ to DMMP 0.5ppm. Response and recovery times were about 1 and 3 min., respectively. Repetition measurement was very good with $\pm$3% in full scale. As a result, operating temperature was lower TEX>$\alpha$-$Al_{2}O_{3}$ than $In_{2}O_{3}$, but sensitivity was higher $In_{2}O_{3}$ than $\alpha$-$Al_{2}O_{3}$.

• Journal of Navigation and Port Research
• /
• v.30 no.4
• /
• pp.291-294
• /
• 2006

Corrosion is never avoided in the use rf materials with various environments. The underwater hull is normally protected against rusting by several coatings of anti-corrosive paint. The purpose of ICCP(Impressed Current Cathodic Protection) system is to eliminate the rusting or corrosion, which occurs on metal immersed in seawater. This thesis is about the ICCP control and monitoring system, which brings protection against the corrosion of the ship's hull in the sea environments. The test system for ICCP is composed of a power supply, anode, reference electrode and controller. The test system is composed power supply, anode, ref electrode, shunt and etc. The protection current is sent to the protection area though anode. Reference electrode senses whether or not the detected potential is within a range of protection of test equipment and then it is automatically controlled to increase or decrease the amount of protective current to be sent to the anode by controller. The monitoring system with LabView is also detected in order to check the normal state of the system at operation period, because an operator does not always watch over this system and thus the system cannot operate well because rf his or her negligent management. This paper was studied the variation of potential and current density with environment factors, velocity and time, and the experimental results will be explained Also, It is suggested that this system can accommodate a ship's automation for SCMS(Ship Control and Management System) and will be very useful.

• Journal of Digital Convergence
• /
• v.11 no.9
• /
• pp.341-348
• /
• 2013

The present study aims to analyze kickers' strategic actions for finishing in penalty shoot-outs among youth soccer players ultimately to increase success rates of shoot-outs and to score a victory. Subjects were experienced 271 soccer players attending high schools located around the capital area. To determine any difference in strategic actions for finishing in penalty shoot-outs among the subjects, frequency analysis or chi-square was used for the analysis. The analysis found the following points: First, the success or failure rates of kickers in penalty shoot-outs were found to depend on subjects' experiences as soccer players. Second, in terms of kickers' shooting qualities, they were found to shoot on goal regardless of shooting positions. Third, an important factor to enhance the shoot-outs probability was found to be a strategic action through the eyes. Fourth, in view of the strategic actions prior to kickers' shooting, goalies were found to check out kickers' positions first and estimate the directions and qualities of shooting via kickers' body actions and eye lines.

• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.267-273
• /
• 2011

In hardware design, its stability and reliability are important, because a hardware error can cause serious damages or disaster. To improve stability and reliability, this paper presents the implementation of the hardware verification system using the fault injection method in PC environment. This paper presents a verification platform that can verify hardware system reliably and effectively, through a process to generate faults as well as insert input signals into the actual running system environment. The verification system is configured to connect a PC with a digital I/O card, and it can transmit or receive signals from the target system, as a verifier's intention. In addition, it can generate faults and inject them into the target system. And it can be monitored by displaying the received signals from the target system to the graphical wave signals. We can evaluate its reliability by analyzing the graphical wave signals. In this paper, the proposed verification system has been applied to the FPGA firmware of a nuclear power plant control system. As a result, we found its usefulness and reliability.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.1
• /
• pp.99-105
• /
• 2011

Location-Based Service(LBS) is a service that provides a variety of convenience in life using location information that can be obtained by mobile communication network or satellite signal. In order to provide LBS precisely and efficiently, we have to need technologies such as location determination technology, platform technology and server technology first. In this study, we studied on how we can reduce the error on location determination of objects such people and things. Fingerprint location determination method was applied to this study because it can be used at current wireless communication infrastructure and less influenced by a variety of noisy environment than other location determination methods. We used the time of arrival(ToA) method in fingerprint location determination method. In order to confirm the performance of suggested method, we developed location determination test program with LAbVIEW 2010 and performed the test. According to indoor test results, the suggested method reduced the distance error by 24%, 34% and 19% respectively at indoor environment compared with deterministic kWNN and Rice Gaussian fingerprint methods.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.560-562
• /
• 2017

This paper presents the development and test results of a test rig for confirming the hover performance of the coaxial propeller which is applied to the drone in order to carry out the mission that requires high payload such as the development of the courier drones. the performance of each propeller was measured by varying the thrust and torque according to the H/D ratio. the Thrust sensor and torque sensor were used to measure the thrust and torque generated when the propeller rotated, and a photo sensor was used to measure the rpm. it used the data acquisition system to acquire data from each sensor, and used the Labview softwaer to control data storage, monitoring and BLDC motor control. In the test, each propeller meansured the figure of mefit according to the chansge of the interval at the same rpm.

• Journal of the Korean Society of Safety
• /
• v.25 no.2
• /
• pp.29-34
• /
• 2010

This paper is aimed to develop monitoring software for detecting the characteristics of current and voltage signals for series arc on electric wire. In order to attain this purpose, the characteristics of series arc were analyzed by the current and voltage signals on electric wire which were installed, and also analyzed by the changes of RMS, instantaneous of waveform value in time domain and THD in frequency domain. Monitoring program which analyze the signal was developed by Labview which can analyze in time domain and frequency domain, and save data. Experimental setup for detecting verification of monitoring program was composed loads of a lamp, an electric heater and an electric fan loads which were usually using. Measurement points for detecting verification of monitoring program were selected at both the panel board and the arc generator at the same time. As results of the experiments by monitoring program, the arc current waveform showed the same characteristic in all measurement points of all load. But the arc voltage waveform was different in each measurement point. When arc occurred, the THD of current value increased above 20%. The results of this study will be effectively used in developing the preventive system of electric fire by series arc.

• IE interfaces
• /
• v.24 no.1
• /
• pp.1-7
• /
• 2011

The purpose of this research was to develop an integrated interface for the usability test of systems or products in the design process. It is capable of automatically creating GOMS models which can predict human task performances. It can generate GOMS models to be interacted with the prototype interfaces. It can also effectively manage various design information and various usability test results to be implemented into the new product and/or system design. Thus we can perform usability test for products or system prototypes more effectively and also reduce time and effort required for this test. For usability tests, we established an integrated interface based on GOMS model by the LabVIEW program. We constructed the system that the linkage to GOMS model is available. Using this integrated interface, the menu structure of mobile phone can be constructed easily. User can design a depth and a breath that he want. The size of button and the label of the button is changable. The path to the goal can be defined by the user. Using a designed menu structure, the experiment could be performed. The results of GOMS model and the actual time are presented. Besides, values of operators of GOMS model can be defined as the value that user wants. Using the integrated interface that we developed, the optimal menu structure deducted. The menu structure that user wants can be established easily. The optimal layout and button size can be decided by comparison of numerous menu structures. User can choose the method of usability test among GOMS model and empirical data. Using this integrated interface, the time and costs can be saved and the optimal menu structure can be found easily.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1237-1242
• /
• 2006

Microsoft's ActiveX corresponding to the advanced type of COM based distributed application model is made available for the use of component communication[1]. ActiveX supports reuse of code and object linking, so developers can integrate many objects into application and improve the efficiency of development. Also, Integration of seperated application makes easy to develop customized program[2]. ActiveX, formerly used to develope communication application in Visual C++ or Visual Basic, has the efficiency of programming and is widely used in the M&C(Monitoring and Control) of instruments. In this paper, we will implement M&C application capable of remote operating, and besides, develop web browser and media player in the form of ActiveX control in order to control and monitor program remotely.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.2
• /
• pp.13-28
• /
• 2003

The purpose of this study was to analyze the kinematic characteristics of Ice hockey slap shot. The subjects of this study were four professional ice hockey players. The reflective markers were attached on the anatomical boundary line of body and the subjects were asked to perform the shot. Ariel Performance Analysis System was used to capture and digitize the shooting image, the data were analyzed by LabView 6i. The results were as fellows. 1. The period of the back swing phase was $0.542{\pm}0.062sec$, the down swing phase was $0.28{\pm}0.056sec$ and the total swing time was $0.825{\pm}0.017sec$ 2. The maximum linear velocity of the stick blade for x direction was shown after 7% of impact, for y, z direction were shown before 2%, 8% of Impact. 3. The maximum velocity of each segment for the left arm was $2.35{\pm}0.05m/s$ in the upper arm, $3.56{\pm}0.34m/s$ in the forearm, $4.75{\pm}0.67m/s$ in the hand. 4. The maximum velocity of each segment for the right arm was $4.67{\pm}0.43m/s$ in the upper arm, $7.22{\pm}0.69m/s$ in the forearm, $9.42{\pm}0.89m/s$ in the hand. 5. The angle of left elbow was generally flexed from the ready stance to the impact and was $82.26{\pm}3.45^{\circ}$ the moment of Impact. 6. The angle of the left shoulder was increased ut the down swing phase and was $78.74{\pm}4.78^{\circ}$ on the moment of impact. 7. The angle of the right shoulder was decreased in the down swing phase and increased before the impact. and the angle was $51.28{\pm}3.54^{\circ}$ on the moment of impact.