• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.12
• /
• pp.641-646
• /
• 2016

Soil organic matter (SOM) is an important soil component releasing nutrients to the plants and reducing risks of soil contamination to the human and ecosystem. Much attention has been recently paid to SOM investigation and management because SOM holds the most of carbon in the earth and sequestrate carbon as a sink tank. The first objective of the study was to investigate SOM of 495 soil samples taken at the Korea Soil Quality Monitoring Network. Soil samples were collected from 16 regions and 8 land use types. The second objective of the study was to find a relationship between the Tyurin method and loss-on-ignition (LOI) method for SOM. The means of SOM by Tyurin and LOI methods were 1.90 and 2.92 % (w/w), respectively. Land uses such as forest, religious area and park where organic matters continuously supply to normally showed higher SOMs than residential and school areas having sandy soils. A regression equation of the relationship between Tyurin and LOI methods was y(Tyurin) = 0.6257x(LOI) + 0.0602 (P-value < 0.001). The coefficient of determination was $R^2=0.749$, relatively linearly related. Although LOI may result in higher SOMs than the Tyurin method, LOI may be a preference for the SOM investigation if various kinds of land uses and many soil samples should be measured.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.151-159
• /
• 2008

The flame-retardant coatings were prepared by blending the synthesized triphosphorus modified polyester in the previous paper and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. It was confirmed that no deterioration of physical properties of PU coatings was observed with the increasing phenylphosphonic acid (PPA) contents. Flame retardancy was tested by a $45^{\circ}$ Meckel burner method and LOI method. With the $45^{\circ}$ Meckel burner method, CATBTP-20C and CATBTP-30C that contain 20 wt% and 30 wt% of PPA, flame retarding component, respectively, showed the first grade flame retardancy with $2.8{\sim}3.9\;cm$ of char length ; and, with LOI method, they exhibited a good flame retardancy as a range of $30{\sim}32%$ of combustion values.

• Resources Recycling
• /
• v.12 no.2
• /
• pp.45-53
• /
• 2003

In 2001, Korea produced a total of 4.91 million metric tons of fly ash, approximately 63.3% of which was recycled. Almost all of the recycled fly ash are used in concrete mixtures and cement industry. Therefore, in order to develop a new usage to increase the utilization of the fly ash, conductive induction was used in this research rather than triboelectrostatic. By applying conductive induction, we could verify the possibility of obtaining high purity fly ash below 1%LOI and high carbon fly ash over 70%LOI from raw fly ash. In this test, the potential difference between the two electrodes was conducted by changing the range of 8 to 16 kV.

• Journal of the Korean Society of Safety
• /
• v.19 no.1
• /
• pp.77-80
• /
• 2004

The purpose of this study was to examine effects of combustion retardation for paper filter impregnated metal salts by measurement of extinguishing concentration, CO concentration, and limiting oxygen index(LOI, ASTM D 2863). And thermal stability analysis using DSC was carried out. In case of extinguishing concentration, $NH_4H_2PO_4$ showed excellent effect of combustion retardation. The result of LOI measurement showed that metal salts possessed good effect of combustion retardation. And thermal analysis using DSC showed that these metal salts possessed thermal stability. In case of CO concentration, CO concentration was increasing because of imperfect combustion process due to combustion retardation effect of metal salts.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.6
• /
• pp.111-116
• /
• 2015

The soil sample obtained from shooting area contaminated with Pb, Cu, and Zn was investigated to determine the chemical forms of heavy metals with Tessier’s sequential extraction method, which is constituted of five fractions such as ‘exchangeable’, ‘bound to carbonate’, ‘bound to oxide’, ‘bound to organic matter’, and residual fractions. The amount of organic matter was measured by loss on ignition (LOI) and then the results of ‘bound to organic matter’ and LOI were compared. The sequential extraction results show that 4.7%-45% of Pb, 6.2%-25.9% of Cu and 3.9%-15.3% of Zn belong to the ‘bound to organic matter’ fraction, but LOI result shows that only 1.0%-2.8% of organic matter exists in the soil sample. In heavy medium separation tests, because Pb and Cu extracted in ‘bound to organic matter’ and residual fractions were removed, the heavy metals in the fractions would exist as heavier forms. These results suggest that the part of heavy metal extracted in ‘bound to organic matter’ fraction would result from the oxidation of metallic forms by hydrogen peroxide and nitric acid used in the fraction, and, consequently, that the ‘bound to organic matter’ fraction should be investigated in detail to determine the removal method and treatment capacity when the Tessier’s sequential extraction method is used to examine heavy metal contaminants resulted from elemental metal like bullets.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.3
• /
• pp.270-280
• /
• 2005

To maximize a synergy effect in flame-retardancy of flame-retardant coatings, phosphorus and chlorine were introduced in polymer chains. Two-components PU flame-retardant modified polyesters (ABTTC-10C, -20C, -30C) were prepared by curing, at room temperature, of isocyanate (allophanate-trimer) and prepared modified polyesters which contain phosphorus and chlorine. To examine the film properties of the prepared flame-retardant coatings, film specimens were prepared with the prepared coatings. The film properties of ABTTC, ABTTC-10C and ABTTC-20C, which contain 0, 10 and 20wt%, 2,4-dichlorobenzoic acid (2,4-DCBA), respectively, were proved to be good, whereas the film properties of ABTTC-30C, which contains 30wt% 2,4-DCBA, were proved to be a little bit poor. Two kinds of flame retardancy tests, $45^{\circ}$Meckel burner method and LOI method, were performed. With the $45^{\circ}$Meckel burner method, three flame-retardant coatings except ABTTC showed less than 3.4 cm of char length, and showed less than 2 seconds of afterflaming and afterglow. From this result, the prepared flame-retardant coatings were proved to have the 1st grade flame retardancy. With the LOI method, the LOI values of the coatings containing more than 10wt% 2,4-DCBA were higher than 30wt%, which means that the coatings possess good flame-retardancy. From these results, it was found that synergistic effect in flame-retardancy was taken place by the introduced phosphorus and chlorine.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.535-537
• /
• 2004

The flame image processing and it's analysis system has been developed for optimal coal firing of thermal power plant, especially for reducing NOx and safe operations. We aimed at gaining the relationship between burner flame image, emissions of NOx and LOI(Loss on ignition) in furnace by utilizing the flame image processing methods. And the relationship determines quantitatively the conditions of combustion on the individual burners. The test was conducted on Samchonpo thermal power plant #4 unit(560MW) of KOSEP which has 24 burners. The system simplified the burner adjustment works in accordance with the real time trending of flame behavior like NOx profiles and unburned carbon profiles for individual burners. But, This kind of conventional method increases the cost as the number of burner are increased. Also there is a difficulty to measure exhausted gas of each burner because of measurement errors. This paper intends to propose the useful "Flame Monitoring System" that can find Low NOX and LOI at the upper furnace and to compare with the conventional System.

• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.169-175
• /
• 2003

Pyrophosphoric lactone modified polyester (PATT) containing two phosphorous functional groups in one unit structure was synthesized to prepare a non-toxic reactive flame-retardant coatings. Then the PATT was cured at room temperature with isocyanate, toluene diisocyanate-isocyanurate , to get a two-component polyurethane flame-retardant coatings (PIPUC). Comparing physical properties of the films of PIPUC with those of film of non-flame-retardant coatings, there was no deterioration observed in physical properties by the introduction of a flame-retarding component into the resin. We found that the char lengths measured by 45$^{\circ}$ Meckel burner method were 3.1∼4.4 cm and LOI values recorded 27∼30%. These results indicate that the coating prepared in this study is a good flame-retardant. The surface structure of coatings investigated with SEM does not show any defects and phase separation.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.8-16
• /
• 2024

Limestone (CaCO₃, calcium carbonate), which is used as a raw material in the portland cement and steel industry, emits CO₂ through decarbonation by high temperatures in the manufacturing process. To reduce CO₂ emissions by the use of raw materials like limestone, it has been proposed to replace limestone with various industrial by-products that contain CaO but less or none of the carbonated minerals, that cause CO₂ emissions. Loss of Ignition (LOI), Thermogravimetric analysis (TG), and Infrared Spectroscopy (IR) are used to quantitative the amount of CO₂ emission by using these industrial by-products, but CO₂ emissions can be either over or underestimated depending on the characteristics of by-product materials. In this study, we estimated CO₂ contents by LOI, TG, IR and DTG(Differential Thermogravimetric analysis) of calcite(CaCO₃) and samples that contain CO₂ in the form of carbonate and whose weight increases by oxidation at high temperatures. The test results showed for CaCO₃ samples, all test methods have a sufficient level of reliability. On the other hand, for the CO₂ content of the sample whose weight increases at high temperature, LOI and TG did not properly estimate the CO₂ content of the sample, and IR tended to overestimate compared to the predicted value, but the estimated result by DTG was close to the predicted valu e. From these resu lts, in the case of samples that contain less than a few percent of CO₂ and whose weight increases during the temperature that carbonate minerals decompose, estimating the CO₂ content using DTG is a more reasonable way than LOI, TG, and IR.

• Structural Engineering and Mechanics
• /
• v.8 no.5
• /
• pp.439-452
• /
• 1999

A simple numerical scheme suitable for tracing the fracture propagation path for structures idealized by means of Hillerborg's classical cohesive crack model is presented. A direct collocation, multidomain boundary element method is adopted for the required space discretization. The algorithm proposed is necessarily iterative in nature since the crack itinerary is a priori unknown. The fracture process is assumed to be governed by a path-dependent generally nonlinear softening law. The potentialities of the method are illustrated through two examples.