• 한국지반신소재학회논문집
• /
• 제18권4호
• /
• pp.193-204
• /
• 2019

본 연구에서는 국내 16개의 무공케이슨 방파제 설계자료를 이용하여 원호활동에 대한 신뢰성분석을 통하여 신뢰성 수준을 분석하였다. 신뢰성 분석을 위하여 지반의 강도 및 단위중량, 피복재와 상치구조물의 단위중량, 상치구조물 상부에 재하되는 하중의 불확실성을 결정하였다. 해석변수의 불확실성을 반영하여 임의로 재현된 무공케이슨 방파제 물성에 대하여 Bishop 간편법을 이용하여 하중 및 저항을 산정하였다. 충분히 많은 회수의 무공케이슨 방파제에 대한 해석을 Monte Carlo Simulation으로 수행하였고, 모든 해석 케이스에 도출된 하중과 저항 값을 수집하여 통계분석을 하였다. Monte Carlo Simulation으로부터 도출되는 파괴확률이 아주 낮은 경우가 파괴확률의 수렴 문제가 발생하여 하중과 저항의 통계특성을 반영하여 FORM(First-Order Reliability Method) 해석을 통해 신뢰수준을 평가하였다. 무공케이슨 방파제의 안전율, 하중 및 저항의 불확실성, 하중 및 저항의 상관성이 신뢰수준에 미치는 영향을 분석하였다.

• 한국정보통신학회논문지
• /
• 제16권3호
• /
• pp.549-557
• /
• 2012

본 논문에서는 CMOS 공정의 p-diff/n-well 다이오드만을 사용한 ISC(Integrated Solar Cell)를 이용하여 MPPT(Maximum Power Point Tracking) 제어 기능을 갖는 온칩 빛에너지 하베스팅 시스템을 제안하였다. MPPT 제어는 PV(Photovoltaic) 셀의 개방전압과 MPP(Maximum Power Point) 전압간의 비례관계를 이용하여, 작은 pilot PV 셀로 하여금 main PV 셀의 MPP를 실시간 추적할 수 있도록 설계하였다. 모의실험 결과 설계된 회로는 MPPT 제어기능을 적용했을 때 부하가 큰 경우에도 MPP 근처의 전압을 부하에 공급함으로써 부하에 연결된 회로가 정상적으로 동작하는 것을 확인하였다. 제안된 회로는 0.18um CMOS 공정으로 설계하였으며, main PV 셀과 pilot PV 셀의 면적은 각각 $8mm^2$와 $0.4mm^2$이다.

• Journal of Communications and Networks
• /
• 제6권3호
• /
• pp.216-225
• /
• 2004

In a cellular network, if there are too many data users in a cell, data may suffer long delay, and system's quality-of-service (QoS) will degrade. Some traditional schemes such as dynamic channel-allocation scheme (DCA) will assign more channels to hot (or overloaded) cells through a central control system (CC) and the throughput increase will be upper bounded by the number of new channels assigned to the cell. In mobile-assisted data forwarding (MADF), we add an ad-hoc overlay to the fixed cellular infrastructure and special channels-called forwarding channels- are used to connect mobile units in a hot cell and its surrounding cold cells without going through the hot cell's base station. Thus, mobile units in a hot cell can forward data to other cold cells to achieve load balancing. Most of the forwarding-channel management work in MADF is done by mobile units themselves in order to relieve the load from the CC. The traffic increase in a certain cell will not be upper bounded by the number of forwarding channels. It can be more if the users in hot cell are significantly far away from one another and these users can use the same forwarding channels to forward data to different cold neighboring cells without interference. We find that, in a system using MADF, under a certain delay requirement, the throughput in a certain cell or for the whole net-work can be greatly improved.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.133-140
• /
• 2001

This paper suggests another system for a cutting force measuring tool in a milling process. Generally, tool dynamometer is taken into account for the most appropriate cutting force measuring tool in the analysis of cutting mechanism. However, high price and limited space make it difficult to be in-situ system for controllable milling process. Although an alternative method using AC current of servo-motor has been suggested, it is unsuitable for cutting force control because of small upper frequency limit and noise. The cutting force measuring system is composed of two load cells placed between the moving table bracket and the nut flange part of ballscrew. It has many advantages such as low cost and wide range measurement than tool dynamometer because of the built-in moving table and the low cost load cell. The static and dynamic model of the measuring system using imbeded load cell is introduced. Various Experiments are carried out to validate both models. By comparing the cutting forces from a series of end milling experiments on the tool dynamometer and the system developed in this paper, the accuracy of the cutting force measuring system is verified. Upper frequency limit is measured by the experiment of dynamic characteristics.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.341-354
• /
• 2003

The purpose of this study was to develop the uniaxial force plate system which is measured by the vertical force. The VGRF(vertical ground reaction force) 1.0 was composed of 2 bath digital scales, 2 indicaters, and analyzing software. This system was newly renovated to VGRF 2,0 which are 2 industrial digital scales, 2 adjustable indicators, and enforced analyzing software. Changes of the new system were as follows. First, the height of the plate was 75% lower than before. Second, sensing ability of the load cell was changed from 90 - 0.05kg to 300 - 0.1kg. Third, the speed of data processing was changed from 17 per second to 60 per second. Fourth, analyzing software was enforced to develop and calculate the data. For the test of the system, two different types(bare foot, high-heeled shoes) gait was adopted. highly skilled female walker(23yrs, height 165cm, body mass 46.8kg) participated for the experimental study. During the dynamic performance(gait analysis), the data of each load cell were very similar to the previous studies. Specifically, bare foot walking had less vertical force than high-heeled shoes. Consequently, VGRF 2.0 can sense the general dynamic movements as well as static load conditions.

• Journal of Power Electronics
• /
• 제16권6호
• /
• pp.2243-2257
• /
• 2016

This paper presents a two stage three-phase proton exchange membrane fuel cell (PEMFC) generation system. When the system is connected to a three-phase load, it is very sensitive to the characteristics and type of the load. Especially unbalanced three-phase loads, which result in a pulsating power that is twice the output frequency at the inverter output, and cause the dc-link to generate low frequency ripples. This penetrates to the fuel cell side through the front-end dc-dc converter, which makes the fuel cell work in an unsafe condition and degrades its lifespan. In this paper, the generation and propagation mechanism of low frequency ripple is analyzed and its impact on fuel cells is presented based on the PEMFC output characteristics model. Then a novel method to evaluate low frequency current ripple control capability is investigated. Moreover, a control scheme with bandpass filter inserted into the current feed-forward path, and ripple duty ratio compensation based on current mode control with notch filter is also proposed to achieve low frequency ripple suppression and dynamic characteristics improvement during load transients. Finally, different control methods are verified and compared by simulation and experimental results.

• 드라이브 ㆍ 컨트롤
• /
• 제17권4호
• /
• pp.97-102
• /
• 2020

This paper presents the basic research for the design and fabrication of a 3D-printed load cell made of NCPC (nano-carbon piezo-resistive composite). We designed a structure that can resonate at a low frequency range of about 5-6 Hz with ANSYS using sensitivity analysis and a response surface method. The design was verified by fabricating the device with a low-quality commercial 3D printer and ABS filament. We conducted a feasibility test for a commercial sensor using 1000 cyclic load tests at 0.3 Hz in a material testing system. A manufacturing process for the 3D printer filament based on the NCPC was also developed using the nano-composite process.

• 레미콘
• /
• 6호통권8호
• /
• pp.32-39
• /
• 1986

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.27-28
• /
• 2009

건축물의 지진모의실험을 수행할 경우, 부재에 작용하는 전단력과 축력의 계측이 필요하다. 본 연구에서는 2축 전단, 1축 압축을 측정할 수 있는 Load Cell의 제작 및 Calibration법을 제시하고 있다.

• 한국지능시스템학회논문지
• /
• 제11권9호
• /
• pp.807-810
• /
• 2001

본 논문은 전자 저울 시스템의 고장으로 인한 손실을 지능형 알고리즘에 의해 사전에 진단하고 예방하는 시스템을 구현하는 것을 목적으로 한다. 전자 저울에 일반적으로 사용되는 로드셀의 구성회로에 저항을 하나 삽입함으로써 필요한 정보를 획득하고 이를 분석, 추론하는 알고리즘을 구성하여 그 효용성을 밝힌다.