• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.981-986
• /
• 1993

A fast algorithm based upon geometry to measure the wafer center and the position of a wafer fiducial mark is developed and implemented on a single-axis aligner. Design issues for a controller when a National Semiconductor's LM629 is used as a PID controller of an aligner are discussed. Performance of an aligner with the algorithm and a LM629 was measured in experiments. The result shows that it takes about 4.1 seconds on average to align a hot wafer supported by metal pins on the chuck.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2003.06a
• /
• pp.161-164
• /
• 2003

This research presents the parallel control scheme of PID servo-driver for shaping of the curved glass. The designed system consists of a PC, main controller and 11 servo-drivers. Each elements are connected by using RS-232C and 8-bit bus communication. In order to guarantee the stability and the control performance, we use the LM629, a precision PID motion controller, and LMD18200, a H-bridge on the servo-drivers. PC calculates position values of 11 DC motors by using the pre-determined curvature value and offers the user interface environment operator.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.886-889
• /
• 2003

In this paper a design of educational robot based on a PC and/or a microprocessor is discussed. The educational robot has 5 DOF and Is made with Swiss Mini Servomotor and Motor Controller IC LM629N. Also, a GUI(Graphical User Interface) is programmed by Visual Basic. This system is completed to consider control properties of the educational robot with 5-DOF that can be changed the parameter of controller by software.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.360-365
• /
• 2003

In this paper, we have developed a general purpose motion controller using an FPGA(Field Programmable Gate Array). The multi-PID controllers on a single chip are implemented as a system-on-chip for multi-axis motion control. We also develop a PC GUI for an efficient interface control. Comparing with the commercial motion controller LM 629 it has multi-independent PID controllers so that it has several advantages such as space effectiveness, low cost and lower power consumption. In order to test the performance of the proposed controller, robot finger is controlled. The robot finger has three fingers with 2 joints each. Finger movements show that position tracking was very effective. Another experiment of balancing an inverted pendulum on a cart has been conducted to show the generality of the proposed FPGA PID controller. The controller has well maintained the balance of the pendulum.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.1
• /
• pp.73-80
• /
• 2004

We have developed a general purpose motion controller using an FPGA(Field Programmable Gate Array). The multi-PID controllers and GUI are implemented as a system-on-chip for multi-axis motion control. Comparing with the commercial motion controller LM 629, since it has multi-independent PID controllers, we have several advantages such as space effectiveness, low cost and lower power consumption. In order to test the performance of the proposed controller, motion of the robot hand is controlled. The robot hand has three fingers with 2 joints each. Finger movements show that tracking was very effective. Another experiment of balancing an inverted pendulum on a cart has been conducted to show the generality of the proposed FPGA PID controller. The controller has well maintained the balance of the pendulum.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.1
• /
• pp.40-45
• /
• 2004

This paper presents the parallel distributed control scheme for shaping of the bent glass. The designed system consists of a PC, a main controller and 11 servo-controllers, the precision motion controllers. Each elements are connected by using RS-232C and 8-bit data bus. In order to guarantee the stability and the control performance, we use a precision PID motion controller and a H-bridge on the servo-drivers. PC calculates position values of 11 DC motors by using the pre-determined curvature value and offers the user interface environment operator. The main controller provides the control instructions and parameter values to 11 servo-controllers by chip enable signal, simultaneously. Using the received commands and parameter values, the servo-controllers control the positions of the DC motors based on PID control scheme.