• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.57-60
• /
• 2008

Recently, new technologies of the PCS (Power Conditioning System) for energy generating using solar cells or fuel cell are required for smaller unit with low cost and high performance. In this paper, the proposed high frequency AC linked DC/AC converter which consisted of LLC resonant and LF cycloconverter is presented, described and verified through the experimental results of 1kW PCS.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.62-63
• /
• 2010

This paper presents a potential for application of Inductive Power Transfer(IPT) to the light railway vehicle system. IPT system allows for a vehicle fitted with existing or new generation batteries to park over a small charging unit and commence charging immediately. Regular charging will allow for smaller batteries to be used in vehicles. In this paper, IPT system uses a full-bridge LLC resonant converter and is possible for the regenerative braking which is an energy recovery mechanism.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.28 no.1
• /
• pp.39-47
• /
• 2023

This paper applies a structural technique with uniform parallel switch characteristics in gates and power loops to minimize the ringing and current imbalance that occurs when a general discrete package (TO-247)-based power semiconductor device is operated in parallel. Also, this propose a heat sink integrated switching module with heat sink design flexibility and high power density. The developed heat dissipation-integrated switching module verifies the symmetry of the parasitic inductance of the parallel switch through Q3D by ansys and the validity of the structural technique of the parallel switch using the LLC resonant converter experiment operating at a rated capacity of 7.5 kW.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.491-499
• /
• 2019

Recently, there has been increasing demand for power quality in power supply devices. The IEC 61000-3-2 standard requires that the AC / DC power supply for lighting meet the specifications for the power factor (PF) and total waveform distortion (THD). In addition, advanced countries in Europe are regulating the ripple rate as 15 ~ 30% for the flicker phenomenon caused by the change in the amount of foot energy due to the change in current of the output terminal. Therefore, domestic standards and regulations are being updated. This study adopted the Flyback converter to satisfy the PFC standard, and has the circuit first and second insulation function. To reduce the low frequency ripple of the LED current, Flyback, Coupled Inductor, LC parallel resonance filter, LLC resonance filter, and Cuk were simulated by PSIM to mimic each LED driving circuit. A coupled LC resonant circuit with a coupled inductor on the primary side and LC resonance on the secondary side was also proposed for output side ripple reduction.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.3
• /
• pp.273-277
• /
• 2016

In this paper, we deals with the digitization of high frequency sine wave power supply using power source of high frequency surgical equipment and RF device. High frequency surgical equipment has been using commonly on medical surgery because of its merits such as programmable depth of incision, availability of incision and coagulation in the same device, increasing the usability on surgical side. However, the core part of the device is consists of vacuum tubes which are expensive, not ease to use and must be imported, therefore it is inevitable of high prices, forces to develop the fully digitized alternative technology. The fully digitized high frequency sine wave power supply for surgical device is proposed and verified by experimental results.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.457-458
• /
• 2011

본 논문에서는 2KW급 LLC 컨버터를 적용한 전원장치의 병렬운전 및 Load Sharing 기법을 제안한다. 각 모듈의 제어기로는 TI사의 TMS320F28035를 사용하였으며 모듈 각각의 독립적인 전압제어를 담당한다. 그리고 Load Share 모드에서는 CAN통신을 사용하여 각 전원장치의 전류제어 및 전압제어를 수행한다. 각 모듈에 전체전류의 1/N의 균일한 전류를 흐르게 하여 각 모듈에 임피던스 불균형으로 인한 스트레스를 줄일 수 있다. 기존방식은 마스터(Master) 모듈의 지령치에 따라 슬레이브(Slave)모듈에서 부한 분담을 수행하는 반면, 제안된 Load Share 알고리즘은 멀티 마스터(Multi-Master: MM) 방식으로써 각 모듈의 평균전류를 레퍼런스로 갖는 구조로 정확한 부하분담을 수행한다.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.182-184
• /
• 2007

본 논문에서는 2단 AC/DC 컨버터와 단일단 AC/DC 컨버터가 가지고 있는 단점들을 개선 할 수 있는 새로운 준 단일 전력단 컨버터를 제안한다. DC/DC 단으로는 동적 특성이 좋은 LLC 컨버터를 채용하여 별도의 제어기 없이 고정 주파수 및 고정 Duty(50%) 발생기에 의해 Open Loop로 구동 시킴으로써 저가격화 및 고효율화를 획득 할 수 있다. 또한 역률개선단은 Boost 컨버터를 채용하고 간단한 제어기 1개를 사용하여 역률 개선과 동시에 DC/DC 단의 최종출력을 제어한다. 기존 2단 PFC 컨버터와는 다르게 PFC 링크전압을 Feedback 하지 않고 DC/DC 단의 최종 출력을 Feedback 하여 제어한다. 제안된 회로의 우수성 검증을 위해 600W급 시작품을 이용한 실험 결과를 제시한다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.373-374
• /
• 2017

최근 개발 및 출시되고 있는 전기자동차(EV) 충전시스템은 3상 AC전원을 입력받아 입력역률개선과 고효율 AC/DC변환을 위한 Interleaved PFC컨버터, Bridgeless PFC컨버터, 3-Level 비엔나정류기(VIENNEA Rectifier) 등의 Topology가 사용되고 있으며, 변환된 DC전압을 입력받아 배터리를 충전하기 위한 절연된 고주파 DC/DC컨버터로 LLC 공진컨버터, 3레벨 컨버터 등이 사용되어 사이즈저감 및 경량화를 꾀하고 있다. 본 논문은 기존 입력역률 개선을 위한 PFC 컨버터와 배터리 충전을 위한 절연형 DC/DC 컨버터 2단으로 구성되어진 충전시스템 대신에 사이즈저감 및 효율개선 그리고 넓은 범위의 출력전압제어(200Vdc~430Vdc)에 대응 할 수 있도록 '단일전력단 3레벨 하이브리드 AC/DC 컨버터'를 제안하였고, 2kW 시제품을 제작하여 실험을 통해 적용 가능성을 입증하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.70-77
• /
• 2008

Conventional PDP power system, which commonly uses two isolation transformer, consists of sustaining power ($V_S$), addressing power($V_A$), and Multi power($V_M$). Because each of these power conversion circuits use transformer and control IC, there are several defects: decrease of efficiency, rise of cost, and parts stress. This paper is proposed the method which operates PDP power system only with one transformer. The proposed method contributes not only to high-efficient performance of the DC/DC power stage and improvement of reliability but also to reduction of cost by reducing volume and size. Also, proposed method is proper to Address Display-period Separation(ADS) which is one of the driving methods of PDP. Superiority of the proposed method is proved by comparison with conventional method and theoretical, experimental analysis.