• Korean Journal of Construction Engineering and Management
• /
• v.14 no.5
• /
• pp.153-163
• /
• 2013

As recent buildings have been more higher and larger, construction vertical lifting planning and operation is a key factor for successful project in tall building. Although many studies have been trying to set up a construction lifting planning system at early stage, there's not existing a control real-time lift operation control system with respect to during construction stage. Therefore, In this study, we use the sensor device to collect the lift operating data for improvement of lift operation efficiency and develope optimum lift operating system which can perform real-time analysis. Finally, we verify the efficiency of proposed system through comparison between realtime operating data and simulated data using proposing system. In this paper, the proposed system show more efficient moving line compared with previous system. This can contribute to development of unmanned lift system.

• KSBB Journal
• /
• v.21 no.2
• /
• pp.103-109
• /
• 2006

For the study of Hericium erinaceum as a useful functional foods and materials, liquid cultivation under two different bioreactors(air-lift fermenter and jar fermenter) which was not studied systematically until now, was conducted as a method of mass cultivation for H. erinaceum. A batch cultivation in an air-lift fermenter and a jar fermenter was examined for enhancing the productivity because of small amounts of mycelial weight and slow growth in case of a liquid culture for H. erinaceum. We found that air lift fermenter system was more effective than jar fermenter for mycelial production of H. erinaceum, and mycelial morphology was a critical factor of the growth. By scale-up and cultivation based on morphological analysis, the conditions for mass production with 30 L and 500 L jar fermenter was 200 and 150 rpm of agitation speed at 1 vvm of aeration rate, respectively, and mycelial dry weight under these conditions was enhanced to about $13{\sim}14g/L$.

• Wind and Structures
• /
• v.9 no.2
• /
• pp.109-124
• /
• 2006

This paper describes the characteristics of the fluctuating lift forces when a circular cylinder vibrates in the cross-flow direction. The response characteristics on elastically supported the circular cylinder was first examined by a free-vibration test. Next, flow-induced vibrations obtained by the free-vibration test were reproduced by a forced-vibration test, and then the characteristics of the fluctuating lift forces, the work done by the fluctuating lift, the behavior of the rolling-up of the separated shear layers were investigated on the basis of the visualized flow patterns. The main findings were that (i) the fluctuating lift forces become considerably large than those of a stationary circular cylinder, (ii) negative pressure generates on the surface of the circular cylinder when the rolling-up of separated shear layer begins, (iii) the phase between the fluctuating lift force and the cylinder displacement changes abruptly as the reduced velocity $U_r$ increases, and (iv) whether the generating cross-flow vibration becomes divergent or convergent can be described based on the work done by the fluctuating lift force. Furthermore, it was found that the generation of cross-flow vibration can be perfectly suppressed when the small tripping rods are installed on the surface of the circular cylinder.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.101-108
• /
• 2012

The purpose of this study is to establish a design method of tower service lift for offshore wind power system, as well as to conduct structure analysis of the service lift system. The service lift system will be built in the internal area of tower of the offshore wind power system. Design and structure analysis for the tower service lift system are conducted to clarify the stability and reliability of the system. Main objective of the design is to secure sufficient capability of transportation of workers and equipment with satisfactory performance within the designed tolerance limit. Total deformation and equivalent stress of the lift system by external load are examined using the results of structure analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.330-333
• /
• 2003

In this thesis. the application of the synchronizing control of the intelligent indoor lift system is showed. The separate axes of the indoor lift system are driven independently. PID controller, synchronous flexible logic compensating method and tilt sensor are applied to enhance the performance of the intelligent indoor lift system. the tilt sensor senses the horizontal error of the whole system. PID controller and synchronous flexible logic are used to compensate the synchronous errors of both the separate axes and whole system to be zero. Namely, using not the hardware coupling but the software algorithm. the indoor life system is operated without the error. Before applying the real system, the simulation using matlab testifies the possibility of the lift system. And the realization of the system is demonstrated with two DC servo motors. In the experiment test, flexible logic to compensate the synchronous error is chosen by the comparative method. the indoor lift system has to be considered the loading factor as the disturbance. Because the intelligent indoor lift system is developed to support the patients who don't change for themselves to move. finally, the system which considers the weight of the patient as the disturbance can carry the patients safely without synchronous and position error.

• Archives of Plastic Surgery
• /
• v.33 no.4
• /
• pp.525-529
• /
• 2006

Purpose: Facial nerve injury is a rare but feared complication of face lift. Uncertainty as to the depth and vulnerability of the facial nerve in face lift dissection causes some surgeon, particularly novices, to dissect slowly. Excessively thin flaps can be made because of fear of nerve injury, contributing to skin slough. Methods: From September 1998 to February 2003, the authors operated on 34 aging face patients using classical face-lift. We had analysed about quantity of skin removal and degree of elevated flap. The authors have found quantity of skin removal was 1.5-2.0 cm, degree of elevated flap was 40-45 degree on average. Results: The authors performed preauricular pre-excision face-lift technique on 12 aging face patients from July 2003 to Feburary 2005 based on experienced surgery. This technique reduced fear of dissecting skin flap necrosis and facial nerve injury because of firmly attached pre-auricular skin removed in advance. Conclusions: We easily dissected SMAS without visual field disturbance, nerve damage and reduced operation time and bleeding loss compared to classical face-lift.

• Journal of computational fluids engineering
• /
• v.17 no.3
• /
• pp.18-24
• /
• 2012

The aerodynamic performance of the pantograph on a high speed train was compared for different pantograph covers which are designed to block the aero-acoustic noise from the pantograph. For the study, two types of cover are designed: wedge and cone types. The lift force of pantograph with cover was compared with the force of pantograph only. The comparison clarified that the cone type cover increases the sideslip angle of the flow and decreases the lift force considerably. However, the wedge type cover changes the flow direction upward and increases the lift force of the pan head. This increment of lift force compensates the decrement of lift force caused by the blocking of the flow into the pantograph lower frame due to cover. Therefore, in case of the wedge type cover, the overall lift force changes slightly compared with the cone type cover.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.6
• /
• pp.711-719
• /
• 2019

At present, wind power is the fastest growing technology in the world. The domestic market depends heavily on imports for wind tower lift. so it manage through the overseas maker. The lift manufacture, establishment and maintenance utility is increasing, localization development of one wind tower lift is necessary with domestic fundamental base technique. In this paper, we will study the components necessary for the development of onshore offshore wind tower elevators, which are currently dependent on total imports, in line with the high growth of the wind market and the enlargement of the wind power generators. First of all, endless winders and cabins, which are the core components of the offshore wind tower lift, were examined for the components that affect the structural safety. Structural analysis was performed on Sheave, which is responsible for most of the lift lifting loads, and Block Stop, a safety device that prevents the cabin from falling in an emergency. The structural suitability was evaluated by comparing with the safety factor. In addition, the on-board control panel combines the control panel of the elevator and the drive motor driving the endless winder for efficient control of the offshore wind tower lift. The addition of features improves ride comfort at departure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.10
• /
• pp.859-870
• /
• 2021

KARI (Korea Aerospace Research Institute) is developing a design framework for the concept and preliminary design of eVTOL aircrafts. A low fidelity mission analysis tool was developed for the eVTOL aircrafts of Lift-Tilt Concept, which have tilt propellers and lift propellers, using open source SUAVE package. For its development, a review for the propeller performance analysis functionality was made. To find the trim solution at each mission segment automatically, an algorithm is implemented, using a global optimization technique through parallel processings and DOE(design of experiment). Using the tool, the one seated eVTOL OPPAV(optionally piloted personal air vehicle) was modeled and evaluated, which results were compared with the preliminary design data.

• Wind and Structures
• /
• v.35 no.3
• /
• pp.157-175
• /
• 2022

This paper highlights the minimization of drag and lift coefficient of different types both side setback tall buildings by the multi-objective optimization technique. The present study employed 48 number both-side setback models for simulation purposes. This study adopted three variables to find the two objective functions. Setback height and setback distances from the top of building models are considered variables. The setback distances are considered between 10-40% and setback heights are within 6-72% from the top of the models. Another variable is wind angles, which are considered from 0° to 90° at 15° intervals according to the symmetry of the building models. Drag and lift coefficients according to the different wind angles are employed as the objective functions. Therefore 336 number population data are used for each objective function. Optimum models are compared with computational simulation and found good agreements of drag and lift coefficient. The design wind angle variation of the optimum models is considered for drag and lift study on the main square model. The drag and lift data of the square model are compared with the optimum models and found the optimized models are minimizing the 45-65% drag and 25-60% lift compared to the initial square model.