• Advances in materials Research
• /
• v.5 no.3
• /
• pp.193-203
• /
• 2016

Compared to metal-to-metal tribology, polymer tribology presents further complexity as it is more prone to be influenced by operating conditions. Over the past two decades, progress in the field of wear of polymers has led to the establishment of more refined wear mechanisms. The current paper establishes the link between different load parameters and the wear rate of polymers, based on experimental investigations. A pin-on-plate reciprocating tribometer was used to examine the wear behaviour of polyamide sliding against a steel counterface, under constant and fluctuating loads, in dry conditions. In addition, the influence of controlled imperfections in the polymer surface upon its wear rate were examined, under cyclic and steady loading, in order to better understand surface fatigue wear of polymers. The imposed imperfections consisted of vertical artificial deep crack (slit) perpendicular or parallel to the direction of sliding. The study concludes with the followings findings; in general, wear of polymers shows a significant tendency to the type of applied load. Under cyclic loads, polymers show an increase in wear rate compared to those tested under static loads. Such increase was found to increase with the increase in cyclic load frequency. It is also demonstrated that surface cracks results in higher wear rates, particularly under cyclic loads.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.4
• /
• pp.10-15
• /
• 2002

Surface states of polydimethylsiloxane (PDMS) treated by plasma were investigated by the analysis by x-ray photoelectron spectroscopy (XPS) and surface voltage decay. Plasma treatment causes the silica-like(SiO$\_$x/, x=3∼4) oxidative layer, which is confirmed with XPS, and lowers surface resistivity from 1.78$\times$1014 Ω/square to 1.09$\times$10$\^$13/ Ω/square with increasing the plasma treatment time. By measuring the decay time constant of surface voltage, the calculated surface resistivity was compared with the value directly measured by a voltage-current method, so good agreement between two methods was obtained. It was observed that the plasma treatment led to decrease of the thermal activation energy of the surface conduction from 31.0 kJ/mol of untreated specimen to 21.8 kJ/mol. It is found that our results allow the examination of effects of plasma on electrical properties of PDMS.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.5
• /
• pp.177-184
• /
• 2016

Since 1980s, 30 years has passed after issues on environmental refugee began to appear. However, why environmental refugee is not considered as refugee officially in international society? Above all, it seems that main point is the responsibility given to those developed countries if they, whom led the climate changes, officially acknowledge environmental refugee. The problem is that environmental refugee has no direct responsibility for causing climate changes. Actually. the responsibility should be granted to the developed and industrialized countries which caused climate changes. In accordance to the refugee protection system established under current international law, it is difficult to include them into refugee category and thus, they can hardly have enough support. It is urgently needed that new refugee treat which have the new standard and solution added to it shall be adopted. To allow new refugee treat to be effective it is compulsory to have constant and binding policy determination and willingness of execution from a united international organization. Of course, before this, countries should try to have common recognition on recognizing new refugee problem and its seriousness as well as solving those problems together. In reality, it is worth considering adoption of semi-forceable type of system as a more effective way, which allocates responsibility of accepting refugee by amount of carbon emitted. Also, as refugee issue has an important influence on mother company and the third countries, execution process of the system has to be defined clearly. For those permanent organizations, they should accurately define environmental factors making refugee and set standards to minimize possibility of abuse and misuse.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.219-228
• /
• 2009

The growing application and the numerous qualities of induction motors (1M) in industrial processes that require high security and reliability levels has led to the development of multiple methods for early fault detection. However, various faults can occur, such as stator short-circuits and rotor failures. Traditionally the diagnosis machine is done through a sinusoidal power supply, in the present paper we study experimentally the effects of the rotor failures, such as broken rotor bars in function of the ac supplying, the load and show the impact of the converter from diagnosis of the machine. The technique diagnosis used is based on the spectral analysis of stator currents or stator voltages respectively according to the types of induction motor ac supplying. So, four different ac supplying are considered: ${\odot}$ the IM is directly by the balanced three-phase network voltage source, ${\odot}$ the IM is fed by a sinusoidal current source given the controlled by hysteresis, ${\odot}$ the IM is fed (in open loop) by a scalar control imposing through ratio V/f=constant, ${\odot}$ the IM is controlled through a vector control using space vector pulse width modulation (SVPWM) technique inverter with an outer speed loop.

• Journal of Korea Technology Innovation Society
• /
• v.8 no.1
• /
• pp.183-208
• /
• 2005

In recent years, national R&D programs tend to become larger and more complicated, which necessitates strengthening the overall coordination of national R&D programs at the inter-ministerial level from the program planning stage. This paper looks into the status and problems of Korea's national R&D programs and proffers ways to improve the current system It highlights the problems shown in the process of the 2004 overall coordination and their rectification. First, various ad-hoc private-led committee brought about inefficiency in decision making process. Therefore, it is necessary to streamline such committees and strengthen the function of the Office of Science and Technology Innovation, Second, in view of the implementation of the overall coordination system, it is necessary to identify the problems in full detail that were raised in the course of the previous year's overall coordination so that new projects can be allotted minimal grades and follow-up activities can be efficiently put into execution. Third, it is necessary to establish standing committees for constant review and efficient utilization that will be devoted to reviewing programs overlapped and their linkage. Fourth, priority of investment regarding the nation's strategic policy direction should be reflected. Fifth, given the lack of performance-based evaluation system, it is necessary to develop macro and micro evaluation indices in conjunction with enacting the tentatively named "Performance-based Law." The overall coordination system of national R&D programs should be supplemented and further developed in relation to the aforementioned problems and their rectification in order to enhance the expertise, fairness, and efficiency of the nation's R&D coordination system.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.59-68
• /
• 2018

Opto-acoustic systems provide structural and functional information regarding biological tissues. Conventional opto-acoustic systems typically employ continuous or pulsed lasers as transmission sources. Compared to lasers, light emitting diodes (LEDs) are cost-effective and relatively portable excitation sources but are non, coherent. Therefore, in this study, a relatively low cost lens - a type of Ramsden eyepiece - was specially designed to theoretically calculate the illumination and achieve a constant brightness across the pupil of an eye. In order to verify the capability of the developed light-emitting diode-acoustic (LEDA) systems, we carried out experiments on bovine and bigeye tuna eyeball samples, which are of similar size to the human eye, using low frequency (10 MHz) and high frequency (25 MHz) ultrasound transducers. High frequency ultrasound transducers are able to provide higher spatial resolution compared to low frequency ultrasound transducers at the expense of penetration depth. Using the 10 MHz and 25 MHz ultrasound transducers, acceptable echo signals (3.82, 3.94, and 5.84 mV at 10 MHz and 282, 1557, 2356 mV at 25 MHz) from depth greater than 3 cm and 6 cm from the anterior surface of the eye were obtained. We thereby confirmed that the LEDA system using a pulsed LED with the designed Ramsden eyepiece lens, used in conjunction with low and high frequency ultrasound transducers, has the potential to be a cost-effective alternative method, while providing adequate acoustic signals from bovine and bigeye tuna ocular areas.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.401-408
• /
• 2005

Recently shield TBM tunnellings are being applied to subway construction in Korean cities. Generally these kinds of tunnellings have the problems in the stability of ground such as subsidence because urban subway is constructed in the shallow depth. A sinkhole occurred on the road just above the tunnel during tunneling in Kwangju, so a survey for upper layer of the tunnel was needed. But conventional Ground Probing Radar can't be applicable due to the presence of steel-mesh screen in the shield segment, so no existent geophysical method is applicable in this site. Because the outer surface of each shield segment is electrically insulated, dipole-dipole resistivity method which is popular in engineering site investigation, was tried to this survey for the first time. Specially manufactured flexible ring-type electrodes were installed into the grouting holes at an interval of 2.4 m on the ceiling. The K-Ohm II system which has been developed by KIGAM and tested successfully in many sites, was used in this site. The system consists of 1000Volt-1Ampere constant-current transmitter, optically isolated 24 bit sigma-delta A/D conversion receiver - maximum 12 channel simultaneous measurements, and graphical automatic acquisition software for easy data quality check in real time. Borehole camera logging with circular white LED lighting was also done to investigate the state of the layer. Measured resistivity data lack of some stations due to failing opening lids of holes, shows general high-low trend well. The dipole-dipole resistivity inversion results discriminate (1) one approximately 4 meter diameter cavity (grouted but incompletely hardened, so low resistivity - less than $30{\Omega}m$), (2) weak zone (100-200${\Omega}m$), and (3) hard zone (high resistivity - more than 1000${\Omega}m$) very well for the distance of 320 meters. The 2-D inversion neglects slight absolute 3-D effect, but we can get satisfactory and useful information. Acquired resistivity section and video tapes by borehole camera logging will be reserved and reused if some problem occurs in this site in the future.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.166-173
• /
• 2011

In this paper, we implemented and analyzed a wireless power transfer (WPT) system with a CSPR topology. CSPR refers to constant current source, series resonance circuit topology of a transmitting coil, parallel resonance circuit topology of a receiving coil, and pure resistive loading. The transmitting coil is coupled by a magnetic field to the receiving coil without wire. Although the electromotive force (emf) is small (about 4.5V), the voltage on load resistor is 148V, because a parallel resonance scheme was adopted for the receiving coil. The implemented WPT system is designed to be able to transfer up to 1 kW power and can operate a LED TV. Before the implementation, the EMF reduction mechanism based on the use of ferrite and a metal shield box was confirmed by an EM simulation and we found that the EMF can be suppressed dramatically by using this shield. The operating frequency of the implemented WPT system is 30.7kHz and the air gap between two coils is 150mm. The power transferred to the load resistor is 147W and the real power transfer efficiency is 66.4 %.

• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.173-181
• /
• 1992

Tantalum pentoxide($Ta_{2}O_{5}$) thin films on p-type (100) silicon wafer were fabricated by RF reactive sputtering. Physical properties and structure of the specimens were examined by XRD and AES. From the C-V analysis, the dielectric constant of $Ta_{2}O_{5}$ films was in the range of 10-12 in the reactive gas atmosphere in which 10% of oxygen gas is mixed. The ratio of Ta : 0 was 1 : 2 and 1 : 2.49 by AES and RBS examination, respectively. The heat-treatment at $700^{\circ}C$ in $O_{2}$ ambient led to induce crystallization. When the heat-treatment temperature was $1000^{\circ}C$, the dielectric constant was 20.5 in $O_{2}$ ambient and 23 in $N_{2}$ ambient, respectively. The crystal structure of $Ta_{2}O_{5}$ film was pseudo hexagonal of ${\delta}-Ta_{2}O_{5}$. The flat band voltage shift(${\Delta}V_{FB}$) of the specimens and the leakage current density were decreased for higher oxygen mixing ratio. The maximum breakdown field was 2.4MV/cm at the oxygen mixing ratio of 10%. The $Ta_{2}O_{5}$ films will be applicable to hydrogen ion sensitive film and gate oxide material for memory device.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.412-419
• /
• 2023

Anion exchange membrane electrolysis is considered a promising next-generation hydrogen production technology that can produce low-cost, clean hydrogen. However, anion exchange membrane electrolysis technology is in its early stages of development and requires intensive research on electrodes, which are a key component of the catalyst-system interface. In this study, we optimized the pressure conditions of the hot-pressing process to manufacture cobalt oxide electrodes for the development of a high uniformity and high adhesion electrode production process for the oxygen evolution reaction. As the pressure increased, the reduction of pores within the electrode and increased densification of catalytic particles led to the formation of a uniform electrode surface. The cobalt oxide electrode optimized for pressure conditions exhibited improved catalytic activity and durability. The optimized electrode was used as the anode in an AEMWE single cell, exhibiting a current density of 1.53 A cm^-2 at a cell voltage of 1.85 V. In a durability test conducted for 100 h at a constant current density of 500 mA cm^-2, it demonstrated excellent durability with a low degradation rate of 15.9 mV kh^-1, maintaining 99% of its initial performance.