• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2196-2198
• /
• 2005

The luminous intensity distribution of a 1W high-power LED with a wide view angle should be concentrated to be used as a light source for an automotive reading lamp. In this paper, an optical lens made of PMMA is simulated by using an optical design software for that purpose. As the result, with the help of the devised lens, the reading light gives over 80 lx at the center of a target surface of radius of 0.2m located below 0.5m from the lamp, and a minimum of 20 lx at the perimeter of the target surface. Thus, a 1W high-power LED with an appropriate lens would suffice for an automotive reading lamp.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.1 no.2
• /
• pp.21-25
• /
• 2008

A CCFL which commonly used in the back light units for the LCD, possess very high brightness hence, was widely used as a line light source. However, the use of CCFL, caused for several environmental concerns since it contain highly toxic mercury, gradually replaced into a LED. But the LED is a spot light source, the dark area occurs in the surface of the back light units. In this paper, we proposed the lens that can convert the spot light into the line light and it can remove the dark area in the surface of the back light units. The lens is composed with the light condensation part and the light guiding part. The conditions obtained will be helpful to plan an optimum structure for such preparation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.269-270
• /
• 2011

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.63-67
• /
• 2015

White light-emitting diode (WLED) is growing interest in using both illumination and communications. This paper reports visible light communication (VLC) composed of a super bright white light-emitting diode, low cost commercial photo-diode and a Fresnel lens. LED driver is consisted of the power MOSFET and MOSFET driver that switches the LED on and off. The modulation bandwidth of the LED used was determined to be 8 MHz. However, it was possible to communicate up to 1 Mbps under illumination of 500 lx because of the weak signal power and a low spectral sensitivity of the SHF213 as a PIN photodiode. In order to enhance the system bandwidth, the LED light was focused on the PIN photodiode by use of the Fresnel lens. As a result of that, visible light link was operated up to modulation bandwidth of the LED. The signal to noise ratio can be improved by 40 dB using an optical concentration at the receiver.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.134-137
• /
• 2010

An LED sensor luminaire for visual function improvement necessitates the control algorithm for light level adjustment and the appropriate lens design. The control algorithm adapts to surround lighting condition, and thus has the advantages of energy saving and glare reduction. The multi-cell lens design improves color temperature uniformity and spatial light distribution of the luminaire. Experimental and simulated results show that this approach contributes noticeably to energy saving and color temperature uniformity of the LED sensor luminaire.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.4
• /
• pp.22-26
• /
• 1979

Microlenses with an extremely small radius of curvature are efficiently use d to couple LED/laser diode light into optica1 fiber. We propose a Tapered lens for the highly efficient coupling of the optical fiber communication light souses into the fiber. Ray optical analysis shows that the maximum coupling efficiency is as high as 90 %, Tapered lens with optimum parameters are fabricated by using heating and pulling technique. Experiment shows that this new technique improves the coupling efficiency by two and four times for LED and laser diode, respectively, as compared with the simple flat - end coupling.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.4
• /
• pp.1-7
• /
• 2013

Optical characteristics including the view angle and color temperature uniformity of LED packages with an integrated lens fabricated by compression molding method are investigated according to lens shape, lens materials, and phosphor coating methods. Four types of lens shape are designed and their optical output power dependence on the refractive index of silicone encapsulant are evaluated. Also, spatial color temperature uniformities of packages fabricated with different phosphor coating methods-direct coating on a chip vs. uniformly mixed with silicone encapsulant- are compared at various view angles. As the result, it is found that phosphor coating method is more effective on color temperature uniformity than lens shape. The maximum color temperature difference of a package with direct coating of phosphor on a chip is 1,340K according to the view angle at the color temperature of 5,000K, and that of a package with uniformly mixed phosphor is 250K, which indicates 1,090K improvement of color uniformity for the latter case.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.145-150
• /
• 2004

The LED lighting used spot-light illuminate the limited surface. So it is a key-point to condense wide emission angle of high power light emitting diodes (LEDs) to narrow that angle. In this paper, the secondary optics was designed by lens-makers formula for concentration rays of LED into specific region. So, it simulated the optics that designed by lens makers-formula in the optical design program, LightTools. And then, show the p propriety of lens design utilizing simulation result, luminous intensity, emission angle.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.128-129
• /
• 1999

Polygon Mirror Scanning(PMS) is composed of LED array, magnifying lens, polygon mirror and motor. It is important to correct the lens aberrations to gain the image we want to show. In this paper, we have simulated the lens aberration correction to reduce the spherical aberration . We have obtained a aspherical lens which is corrected the spherical aberration.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.487-492
• /
• 2012

In this study we researched a spotlight in LED lighting. Ordinary LED spotlight was manufactured with characterized property of traveling straightness of LED light source, but multiple use of shell type LED, a yellow band has formed caused by light source interference between the LED. Also, there was a high miscellaneous light efficiency with losing light source homogeneity and efficiency due to light source control uneasiness. The study uses aspheric reflector and aspheric lens, so we can control the light source of LED spotlight with effectively and we reached surface light source by using COB/COM for LED module. Furthermore it can change its use by a reduced scale of light system. It has been designed to make its various application from low power consumption of bicycle lamp, up to high power consumption of automobile lamps and lighthouse.