• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.87-93
• /
• 2011

We developed a fluorene-containing multifunctional binder polymer for LCD color filter resist, and employing the binder polymer, carbon black based black photoresist (CBR) was prepared in order to apply it to the black matrix (BM). To obtain the multifunction of the binder polymer, we synthesized bisphenol fluorene epoxy acrylate-containing unsaturated polyester and identified the binder polymer structure with $^1H$ NMR, GPC and FTIR. The corresponding BFEA-polyester binder polymer was compared with the commercially available acryl binder toward the application to the CBR. From the BM lithography test, we found that the synthesized BFEA-polyester binder had better photocrosslinking capability and alkali solubility. In addition, the newly developed binder gave a good process margin, good resolution and adhesion property on a glass substrate.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.10
• /
• pp.61-66
• /
• 2007

A gain enhancement rail-to-rail buffer amplifier for liquid crystal display (LCD) source driver is proposed. An op-amp with extremely high gain is needed to decrease the offset voltage of the buffer amplifier. Cascoded floating current source and class-AB control block in the op-amp achieve a high voltage gain by reducing the channel length modulation effect in high voltage technologies. HSPICE simulation in $1\;{\mu}V$ 15 V CMOS process demonstrates that voltage gain is increased by 30 dB. The offset voltage is improved from 6.84 mV to $400\;{\mu}V$. Proposed op-amp is fabricated in an LCD source driver IC and overall system offset voltage is decreased by 2 mV.

• Computers and Concrete
• /
• v.24 no.2
• /
• pp.151-158
• /
• 2019

The sustainable development principle of replacing natural resources with renewable material is an important research topic. In this study, waste LCD (liquid crystal display) glass powder was used to replace cement (0%, 10%, 20% and 30%) through a volumetric method using three water-binder ratios (0.47, 0.59, and 0.71) to make cement mortar. The compressive strength was tested at the ages of 7, 28, 56 and 91 days. The test results show that the compressive strength increases with age but decreases as the water-binder ratio increases. The compressive strength slightly decreases with an increase in the replacement of LCD glass powder at a curing age of 7 days. However, at a curing age of 91 days, the compressive strength is slightly greater than that for the control group (glass powder is 0%). When the water-binder ratios are 0.47, 0.59 and 0.71, the compressive strength of the various replacements increases by 1.38-1.61 times, 1.56-1.80 times and 1.45-2.20 times, respectively, during the aging process from day 7 to day 91. Furthermore, a prediction model of the compressive strength of a cement mortar with waste LCD glass powder was deduced in this study. According to the comparison between the prediction analysis values and test results, the MAPE (mean absolute percentage error) values of the compressive strength are between 2.79% and 5.29%, and less than 10%. Thus, the analytical model established in this study has a good forecasting accuracy. Therefore, the proposed model can be used as a reliable tool for assessing the design strength of cement mortar from early age test results.

• Clean Technology
• /
• v.15 no.4
• /
• pp.253-257
• /
• 2009

The waste solution discharged form the LCD(Liquid Crystal Display) manufacturing process contains phosphoric acid, nitric acid, acetic acid and metal ions such Al and other impurities. In this study, vacuum evaporation and diffusion dialysis was developed to commercialize an efficient system for recovering the high-purity phosphoric acid and manufacturing monoammonium phosphate. By vacuum evaporation, almost 99% of nitric and acetic acid was removed. Also, by diffusion dialysis, about 97.5% of Al was removed. Monoammonium phosphate was manufactured from purified phosphoric acid and ammonium hydroxide. In order to get the optimum manufacturing condition, the molar ratio of ammonium hydroxide and phosphoric acid, pH and temperature was controlled. Using this optimum condition, we obtained the recovery rate of monoammonium phosphate of about 90%.

• Composites Research
• /
• v.19 no.6
• /
• pp.8-15
• /
• 2006

In this study, computational rotor dynamic analyses of a composite roller used for large LCD panel manufacturing process have been conducted. The present computational method is based on the general finite element method with rotating gyroscopic effects of rotor systems. General purpose commercial finite element code, SAMCEF which has special rotordynamics analysis module is applied. For the purpose of numerical verification, comparison study for a benchmark dual rotor model with support bearings is also presented. Detailed finite element models for composite roller with optimized lamination angles are constructed and analyzed considering gravity effect in order to investigate vibration characteristics in actual operation environment. As results of the present study, rotor stability diagrams and mass unbalance responses are presented for different rotating conditions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.328-330
• /
• 2004

In order to stabilize the rubbing process for liquid crystal panels, the authors developed "the sparkling dot area ratio evaluation method". This method quantifies the fiber length dispersion of rubbing cloths, which is a major cause of mura defects. The newly developed method enables quantitative evaluation of rubbing cloths and contributes to the improvement of rubbing process uniformity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1319-1322
• /
• 2007

Planar PIN photodiode is compatible with LTPS process, and its fabrication requires no additional manufacturing process. In this study we design the optimum dimension of PIN diodes with two nitride layers to improve the efficiency of PIN diodes. The PIN photo sensor shows very good sensitivity to ambient light illuminance.

• Journal of Information Display
• /
• v.4 no.4
• /
• pp.1-3
• /
• 2003

For excimer laser annealing (ELA), energy density, number of pulses, beam uniformity, and condition of initial amorphous Si (a-Si) films are significant factors contributing to the final microstructure and the performance of low-temperature polycrystalline Si (LTPS) TFTs. Although the process and equipment have been significantly improved, the environmental factors associated with initial amorphous Si (a-Si) films and process conditions are yet to be optimized.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.903-906
• /
• 2008

We developed the advanced LTPS (A-LTPS) manufacturing process. The a-Si TFT process was combined with selectively enlarging laser crystallization (SELAX) technology to improve the carrier mobility in the region where the peripheral circuits are to be fabricated. A 2.4-inch IPS-pro LCD panel for personal digital assistant use was successfully fabricated using the developed technology.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.533-536
• /
• 2006

VIATRON TECHNOLOGIES has developed Field-Enhanced Rapid Thermal Processor (FERTP) system that enables LTPS LCD and AMOLED manufacturers to produce poly-Si films at low cost, high throughput, and high yield. The FE-RTP allows the diverse process options including crystallization, thermal oxidation of gate oxides and fast pre-compactions. The process and equipment compatibility with a-Si TFT lines is able to provide a viable solution to produce poly-Si TFTs using a-Si TFT lines.