• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.555-566
• /
• 2015

A TRIAC dimming LED driver that can control the brightness of LED arrays for a wide range of source voltage variations is proposed in this paper. Unlike conventional PWM LED drivers, the proposed LED driver adopts a TRIAC switch, which inherently guarantees zero current switching and has been proven to be quite reliable over its long lifetime. Unlike previous TRIAC type LED drivers, the proposed LED driver is composed of an LC input filter and a variable switched capacitance, which is modulated by the TRIAC turn-on timing. Thus, the LED power regulation and dimming control, which are done by a volume resistor in the same way as the conventional TRIAC dimmers, can be simultaneously performed by the TRIAC control circuit. Because the proposed LED driver has high efficiency and a long lifetime with a high power factor (PF) and low total harmonic distortion (THD) characteristics, it is quite adequate for industrial lighting applications such as streets, factories, parking garages, and emergency stairs. A simple step-down capacitive power supply circuit composed of passive components only is also proposed, which is quite useful for providing DC power from an AC source without a bulky and heavy transformer. A prototype 60 W LED driver was implemented by the proposed design procedure and verified by simulation and experimental results, where the efficiency, PF, and THD are 92%, 0.94, and 6.3%, respectively. The LED power variation is well mitigated to below ${\pm}2%$ for 190 V < $V_s$ < 250 V by using the proposed simple control circuit.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.11
• /
• pp.1543-1550
• /
• 2015

Ferroresonance is a non-linear vibrational phenomenon that is generated by the electrical interaction of the inductance component with the capacitor component of a certain capacitance as the device of the inductance component such as a transformer is saturated due to the degradation, the waveform distortion of current and voltage, and the oscillation of overcurrent and overvoltage in a system. Recently, ferroresonance was generated from the waveform distortion of current and voltage, or the overvoltage or undervoltage phenomenon caused by the nature of an electrical power system and design technology of the transformer in the three phase transformer system. Hence, in general, ferroresonance analyzed by converting to the LC equivalent circuit. However, in general, the aforementioned analytical method only applies to the resonance phenomenon that is generated by the interaction of the capacitance of bussbar and grounding, and switching as the capacitor component with PT and the transformer as the inductance component in a system. Subsequently, the condition where ferroresonance was generated since overvoltage was supplied as line voltage to the phase voltage and thus the iron core is saturated due to the interconnection between grounded and ungrounded systems could not be analyzed when single phase PT was connected in a ${\Delta}$/Y connection system. In this study, voltage swell in the configuration of grounded circuit of a step-up transformer with the ${\Delta}-{\Delta}$ connection linked to PT for control power and the ferroresonance generated by overvoltage when the line voltage of the ${\Delta}-{\Delta}$ connection was connected to the phase voltage of the grounded Y-Y connection were analyzed using PSCAD / EMTDC through the failure case of the transformer caused by ferroresonance in the system with the ${\Delta}-{\Delta}$/Y-Y connection, and subsequently, the preventive measure of ferroresonance was proposed.

• Restorative Dentistry and Endodontics
• /
• v.33 no.6
• /
• pp.570-579
• /
• 2008

The purpose of this study was to investigate the distribution of tensile stress of canal obturated maxillary second premolar with access cavity and notch-shaped class V cavity restored with composite resin using a 3D finite element analysis. The tested groups were classified as 8 situations by only access cavity or access cavity with notch-shaped class V cavity (S or N), loading condition (L1 or L2), and with or without glass ionomer cement base (R1 or R2). A static load of 500 N was applied at buccal and palatal cusps. Notch-shaped cavity and access cavity were filled microhybrid composite resin (Z100) with or without GIC base (Fuji II LC). The tensile stresses presented in the buccal cervical area, palatal cervical area and occlusal surface were analyzed using ANSYS. Tensile stress distributions were similar regardless of base. When the load was applied on the buccal cusp, excessive high tensile stress was concentrated around the loading point and along the central groove of occlusal surface. The tensile stress values of the tooth with class Ⅴ cavity were slightly higher than that of the tooth without class V cavity. When the load was applied the palatal cusp, excessive high tensile stress was concentrated around the loading point and along the central groove of occlusal surface. The tensile stress values of the tooth without class V cavity were slightly higher than that of the tooth with class V cavity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1125-1134
• /
• 2011

In this paper a wideband frequency synthesizer is designed for DTV tuners using a $0.18{\mu}m$ CMOS process. It satisfies the DTV frequency band(48~1675MHz). A scheme is proposed to cover the full band using only one VCO and reliable broadband characteristics are achieved by reducing the variations of VCO gains and frequency steps. The simulation results show that the designed VCO has frequency range of 1.85~4.22GHz, phase noise at 4.22GHz of -89.7dBc/Hz@100kHz, gains of 62.4~95.8MHz/V(${\pm}21.0%$) and frequency steps of 22.9~47.9MHz(${\pm}35.3%$). The designed VCO has a phase noise of -89.75dBc/Hz at 100kHz offset. The designed synthesizer has a lock time less than $0.15{\mu}s$. The measured VCO tuning range is 2.05~3.4GHz. The frequency range is shifted down but still satisfy the target range owing to the design for enough margin. The designed circuit consumes 23~27mA from a 1.8V supply, and the chip size including PADs is $2.0mm{\times}1.5mm$.

• Culinary science and hospitality research
• /
• v.22 no.2
• /
• pp.13-28
• /
• 2016

This study performed quantitative analysis of isoflavone glycoside contents on Buseoktae, Daewon, Wooram beans and cheonggukjang made of Buseoktae beans from the LC/MS/MS. Also, the experiment carried out by means of RSM(response surface methodology), which included 10 experimental points for the two independent variables addition(40, 55, 70 g) and time(2, 3, 4 min) from the beginning point to boil of cheonggukjang. These were optimized using a Face-centered central composite design. Daidzein contents were $212.16{\mu}g/mL$ in Buseoktae, $212.21{\mu}g/mL$ in daewon, $158.54{\mu}g/mL$ in wooram beans. Genistein contents were $318.84{\mu}g/mL$ in Buseoktae, $310.50{\mu}g/mL$ in daewon, $262.71{\mu}g/mL$ in wooram beans. Total isoflavone contents were $532.50{\mu}g/mL$ in Buseoktae, $524.19{\mu}g/mL$ in Daewon, $422.71{\mu}g/mL$ in Wooram beans. Isoflavone contents of Buseoktae and Daewon were quite similar, relatively contents of Wooram beans were low. Total isoflavone contents of Buseoktae cheonggukjang (for business use) was $430.10{\mu}g/mL$ in A ($32^{\circ}C$, 96 h fermentation), $460.09{\mu}g/mL$ in B ($36{\sim}40^{\circ}C$, 30 h fermentation), $417.46{\mu}g/mL$ in C cheonggukjang($36{\sim}38^{\circ}C$, 72 h fermentation), B cheonggukjang was just a bit more than A, C cheonggukjang. The estimated response surfaces confirmed that the amount and time had significant effects on taste. The optimum condition of Buseoktae cheonggukjang taste was predicted to be 55.20 g addition at 2.92 min.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.58-72
• /
• 2009

In this study, the organic matter and biomass was characterized by using respirometry based on ASM No.2d (Activated Sludge Model No.2d). The activated sludge models are based on the ASM No.2d model, published by the IAWQ(International Association on Water Quality) task group on mathematical modeling for design and operation of biological wastewater treatment processes. For this study, OUR(Oxygen Uptake Rate) measurements were made on filtered as well as non-filtered wastewater. Also, GC-FID and LC analysis were applied for the estimation of VFAs(Volatile Fatty Acids) COD(S_A) in slowly bio-degradable soluble substrates of the ASM No.2d. Therefore, this study was intended to clearly identify slowly bio-degradable dissolved materials(S_S) and particulate materials(X_I). In addition, a method capable of determining the accurate time to measure non-biodegradable COD(S_I), by the change of transition graphs in the process of measuring microbial OUR, was presented in this study. Influent fractionation is a critical step in the model calibrations. From the results of respirometry on filtered wastewater, the fraction of fermentable and readily biodegradable organic matter(S_F), fermentation products(S_A), inert soluble matter(S_I), slowly biodegradable matter(X_S) and inert particular matter(X_I) was 33.2%, 14.1%, 6.9%, 34.7%, 5.8%, respectively. The active heterotrophic biomass fraction(X_H) was about 5.3%.

• Resources Recycling
• /
• v.28 no.6
• /
• pp.3-8
• /
• 2019

Recently, plastic waste in Korea has been recognized as a critical issue due to an increase in massive production of plastics, difficulty in disposal of waste plastics, and public recognition of toxicity in micro-plastics, etc. To resolve those problems, the regulation to reduce plastics consumption may be primarily considered but, in this case, clarification should be made on the rationales and the action plans in the regulation for individual waste plastic items. Another problem is the small capital sizes of domestic recycling companies, which leads to poor R&D capacity, low recycling yields and thus lowering values of recycling items. This adversely affects consumers' perception. The R&D toward recycling technical progress should take into account the environmental friendliness and recyclability from the early product design stages. Certainly, this should be supported in governmental policy and public action plans. In addition, by referring to advanced policies of i.e. European Union, the recycling industry should be recognized as an opportunity toward new investment & employment. If necessary, the regulation of plastic consumption through a formal evaluation process such as Life Cycle Assessment (LCA) will also be helpful. The values of recycled plastics should be improved through the identification and elimination of harmful chemical substances potentially contained in the products.

• Korean Journal of Plant Resources
• /
• v.33 no.4
• /
• pp.311-336
• /
• 2020

The flora of Sejong were summarized as 531 taxa including 104 families, 315 genera, 462 species, 3 subspecies, 59 varieties and 7 form. The rare plants were 8 taxa including Nepeta cataria L. and Aristolochia ontorta Bunge. The Korea endemic plants were 9 taxa including Populus tomentiglandulosa T. B. Le and Clematis trichotoma Nakai.. The specific plants were 42 taxa including Phytolacca esculenta Van Houtte(V), Corydalis decumbens (Thunb.) Pers(IV), Poncirus trifoliata Raf(III), Pseudostellaria coreana (Nakai) Ohwi(II), Cyrtomium fortunei J.Sm.(I). The naturalized plants were 49 taxa including Sicyos angulatus L, Ambrosia trifida L, Physalis angulata L. Panicum dichotomiflorum Michx., Galinsoga parviflora Cav, and Erigeron philadelphicus L. Especially, Sicyos angulatus L., Phytolacca americana L. and Bidens frondosa L. have been spread throughout the country are required to manage. The naturalized index(NI) and urbanized index(UI) were 8.7% and 15.3%. Useful plants incuding Edible was 199 taxa, Pasture was 193 taxa, Medicinal was 178 taxa, Ornamental was 82 taxa, Timber was 25 taxa, Fiber was 18 taxa, Stain was 9 taxa. Useful plants will be important materials for plant design in recreational and healing forests.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.65-74
• /
• 2010

The Digital TV(DTV) standard has ushered in a new era in TV broadcasting and raised a great demand for DTV tuners. There are many challenges in designing a DTV tuner, of which the most difficult part is the frequency synthesizer. This paper presents the design of a frequency synthesizer for DTV Tuners in a $0.18{\mu}m$ CMOS process. It satisfies the DTV(ATSC) frequency band(54~806MHz). A scheme is proposed to cover the full band using only one VCO. The VCO has been designed to operate at 1.6~3.6GHz band such that the LO pulling effect is minimized, and reliable broadband characteristics have been achieved by reducing the variations of VCO gain and frequency step. The simulation results show that the designed VCO has gains of 59~94MHz(${\pm}$17.7MHz/V,${\pm}$23%) and frequency steps of 26~42.5MHz(${\pm}$8.25MHz/V,${\pm}$24%), and a very wide tuning range of 76.9%. The designed frequency synthesizer has a phase noise of -106dBc/Hz at 100kHz offset, and the lock time is less than $10{\mu}$sec. It consumes 20~23mA from a 1.8V supply, and the chip size including PADs is 2.0mm${\times}$1.8mm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.443-451
• /
• 2010

This paper describes a fully integrated CMOS low-IF mobile-TV RF tuner for Band-III T-DMB/DAB applications. All functional blocks such as low noise amplifier, mixers, variable gain amplifiers, channel filter, phase locked loop, voltage controlled oscillator and PLL loop filter are integrated. The gain of LNA can be controlled from -10 dB to +15 dB with 4-step resolutions. This provides a high signal-to-noise ratio and high linearity performance at a certain power level of RF input because LNA has a small gain variance. For further improving the linearity and noise performance we have proposed the RF VGA exploiting Schmoock's technique and the mixer with current bleeding, which injects directly the charges to the transconductance stage. The chip is fabricated in a 0.18 um mixed signal CMOS process. The measured gain range of the receiver is -25~+88 dB, the overall noise figure(NF) is 4.02~5.13 dB over the whole T-DMB band of 174~240 MHz, and the measured IIP3 is +2.3 dBm at low gain mode. The tuner rejects the image signal over maximum 63.4 dB. The power consumption is 54 mW at 1.8 V supply voltage. The chip area is $3.0{\times}2.5mm^2$.