• Wind and Structures
• /
• v.7 no.2
• /
• pp.131-144
• /
• 2004

A technique for the simulation of atmospheric boundary layers in wind tunnels is developed and tested experimentally. The device consists of a grid made of seven horizontal and vertical evenly distributed bars in which air injection holes are drilled in order to influence the flow in the wind tunnel. The air flow in each bar can be controlled independently. Firstly, the device is used together with a rough carpet, which covers the test section floor, in order to simulate the boundary-layer characteristics over an open rural area. Hot-wire measurements, performed at different positions in the test-section, show the capability of the grid in generating the required boundary layer. An acceptable agreement with statistical values of mean velocity and turbulence profiles has been achieved, together with a good span-wise homogeneity. The results are also compared with those of a passive simulation technique based on the use of spires.

• Steel and Composite Structures
• /
• v.8 no.5
• /
• pp.423-438
• /
• 2008

This paper reports an experimental investigation of the behaviour of concrete-encased composite columns subjected to short-term axial load and biaxial bending. In the study, six square and four L-shaped cross section of both short and slender composite column specimens were constructed and tested to examine the load-deflection behaviour and to obtain load carrying capacities. The main variables in the tests were considered as eccentricity of applied axial load, concrete compressive strength, cross section, and slenderness effect. A theoretical procedure considering the nonlinear behaviour of the materials is proposed for determination of the behaviour of eccentrically loaded short and slender composite columns. Two approaches are taken into account to describe the flexural rigidity (EI) used in the analysis of slender composite columns. Observed failure mode and experimental and theoretical load-deflection behaviour of the specimens are presented in the paper. The composite column specimens and also some composite columns available in the literature have been analysed and found to be in good agreement with the test results.

• Wind and Structures
• /
• v.1 no.1
• /
• pp.59-66
• /
• 1998

The vibrations of bodies subjected to fluid flow can cause modifications in the flow conditions, giving rise to interaction forces that depend primarily on displacements and velocities of the body in question. In this paper the linearized equations of motion for bodies of arbitrary prismatic or cylindrical cross-section in two-dimensional cross-flow are presented, considering the three degrees of freedom of the body cross-section. By restraining the rotational motion, equations applicable to circular tubes, pipes or cables are obtained. These equations can be used to determine stability limits for such structural systems when subjected to non uniform cross-flow, or to evaluate, under the quasi static assumption, their response to vortex or turbulent excitation. As a simple illustration, the stability of a pipe subjected to a bidimensional flow in the direction normal to the pipe axis is examined. It is shown that the approach is extremely powerful, allowing the evaluation of fluid-structure interaction in unidimensional structural systems, such as straight or curved pipes, cables, etc, by means of either a combined experimental-numerical scheme or through purely numerical methods.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.236-243
• /
• 2018

A series of $Er^{3+}/Yb^{3+}$ co-doped fluorophosphate glasses with varying $YbF_3$ concentration were prepared by a high temperature melt quenching technique. Absorption and emission cross-sections were determined by using the McCumber theory. The larger emission cross-section ($9.86{\times}10^{-21}cm^2$) and longer fluorescence lifetime (12.37 ms) were obtained for the $^4I_{13/2}{\rightarrow}^4I_{15/2}$ transition of ABS3Er4Yb glass. The sensitivity and temperature of the maximum sensitivity were evaluated by the fluorescence intensity ratio method from the measured upconversion spectra. The results were discussed and compared to the other reported glasses.

• Food Science of Animal Resources
• /
• v.37 no.4
• /
• pp.542-551
• /
• 2017

The quality characteristics of velvet antlers obtained from Formosan sambar deer (Cervus unicolor Swinhoi) (SDVA), harvested from 63 to 81 d during the velvet antler growth period, were evaluated by investigating the relationships between antioxidant levels; including content, activity, and content/activity ratios, and physical properties; including shear force values, color, and Ca content. The hardness of samples from base velvet antler sections increased, and that the color of these samples tended to become reddish-yellow (redder and more yellow), suggesting that the Ca content in the base section of the sample was not ossified yet. Samples from the upper sections of velvet antler showed higher superoxide dismutase (SOD), catalase (CAT), and glutathione peroxidase (GPX) content (3.91 to 1.50 mg/mL, 2.53 to 0.90 mg/mL, and 3.95 to 1.58 mg/mL, respectively) than did samples from the middle and base sections (p<0.05). The activity and content/activity ratios of GPX measured in the upper section were also found to be significantly greater than in the middle and base sections (p<0.05). We further observed that the content and activity of GPX was significantly and negatively correlated with Ca content, shear force values, and the content/activity ratio of this antioxidant (p<0.01). The study findings may serve as a reference index for quality evaluations of velvet antlers of Formosan sambar deer in future.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1505-1515
• /
• 2009

A new method to semicontinuously determine $PM_{2.5}$ ionic species with a short time resolution is described in detail. In this system, a particle collection section (mixing part, particle collection chamber, and air/liquid separator) was developed. A Y-type connector was used to mix steam and an air sample. The particle collection chamber was constructed in the form of a helix coil and was cooled by a water circulation system. Particle size growth occurred due to the high relative humidity and water absorbed particles were efficiently collected in it. Liquid samples were drained out with a short residence time (0.08-0.1 s). The air/liquid separator was also newly designed to operate efficiently when the flow rate of the air sample was 16.7 L $min^{-1}$. For better performance, the system was optimized for particle collection efficiency with various types of test aerosols such as ($NH_4)_2SO_4,\;NaCl,\;NH_4HSO_4,\;and\;NH_4NO_3$. The particle collection efficiencies were almost 100% at different concentration levels in the range over 500 nm in diameter but 50-90% in the range of 50-500 nm under the following experimental conditions: 15 coil turns, a water flow rate for steam generation of 0.65 mL $min^{-1}$, and an air sample flow rate of 16.7 L $min^{-1}$. Finally, for atmospheric applications, chemical compositions of $PM_{2.5}$ were determined with a time resolution of 20 min on January 11-24, 2006 in Seoul, Korea, and the chemical characteristics of $PM_{2.5}$ ions were investigated.

• Wind and Structures
• /
• v.37 no.6
• /
• pp.399-412
• /
• 2023

Previous studies have shown that the integrated transfer function (ITF) is independent of turbulence characteristics and can be effectively applied to predict the buffeting response of elongated structures, assuming that the strip hypothesis is valid. However, existing research has not effectively identified the ITF through segment model vibration tests, and the influence of the 3D effect on the accuracy of the strip hypothesis and the characteristics of the ITF in wind tunnel tests has not been quantitatively studied. A segment model vibration measurement device that can change a test model's span-width ratio was designed in this study. An airfoil section and a streamlined box girder section structure were taken as the background, and their ITFs were effectively identified under different L/B (L denotes the turbulent integral scale and B denotes the structural width) and model span-width ratios. The influence laws of the 3D effect on the accuracy of the strip hypothesis and ITF identification in wind tunnel tests were systematically investigated. The results showed that L/B and the structural span-width ratio are two significant controlling factors that affect the accuracy of the strip hypothesis and ITF identification. The research provides an effective experimental method for accurately predicting the buffeting response of elongated structures based on ITFs identified through segment model vibration tests.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.31 no.1 s.49
• /
• pp.121-125
• /
• 2005

Most of the cells, specially in the skin, free radicals and reactive oxygen species induced aging, accompanying with diseases. The pinaceae family is very familiar plant with Korean spirit. However, those plants were not estimated for natural products in manufactural process. We employed 4 different plants, Pinus koraienis S et Z. Pinus banksiana LAMBERT. Pinus rigida MILL. Pinus densiflora S. et Z. in pinceae family. The ethanol extracts were prepared for three different parts of plant, wood, bark and leaf, respectively. In this study, we carried out free radical and superoxide radical scavenging assay to investigate the anti-oxidative activity The bark and leaf part of plants showed similar anti-oxidant effect. L-ascorbic acid and $\alpha$-tocopherol at $10{\mu}g/mL$. Also we tried to investigate inhibitory effects of elastase activity in in vitro experiments on pinaceae plant extract as a matters for functional cosmetics. Among those plants, the bark of Pinus rigida MILL. and Pinus densiflora S. et Z. showed inhibitory effect. The cell viability was evaluated with MTT assay. The potential relationship was shown between the cell viability and anti-oxidant effect because the anti-oxidant effects were positively correlated wvith the cell growth in MTT assay. As the results in our experiments, we expect the potential activities of pinaceae as a material of functional cosmetics.

• The Korean Journal of Mycology
• /
• v.13 no.4
• /
• pp.249-262
• /
• 1985

Mushrooms were collected at Mt. Gyeryong, Mt. Chilgab, Mt. Ducyu, Mt. Chiri, Mt Songri and the regions of Chungnam Province for 15 months from July, 1983 to October, 1984. They were classified into 19 species, four varieties and one form of Lactarius. These species were grouped into six sections according to Hesler and Smith. Of these Lactarius, nine species and four varieties appeared to be newly found ones.

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.935-942
• /
• 1994

Two types of ABS were prepared from diffrent types of rubber, and blends of the ABS and PMMA were compounded and evaluated in terms of morphology, mechaincal and rheological properties. In addition, the effect of carbon black in the ABS/PMMA blends were studied. With increasing PMMA content, flexural modulus, tensile yield strength, and surface gloss of the blends increased, but elongation at break and Izod Impact strength decreased. With carbon black addition, mechanical properties were generally decreased. Effects of the type of ABS, and carbon black on melt properties were also studied.