• 한국가구학회지
• /
• 제17권2호
• /
• pp.25-34
• /
• 2006

This experiment was carried out to investigate the high-frequency gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on MDF edge-glued boards. The edge-glued boards were glued lengthwise with butt, scarf, or finger joint. The wastes of MDF boards were reused as board materials. The obtained results are summarized as follows; the bending strength of edge-glued MDF increased slightly with the HF heating time, but the economically desirable heating time was 6 minutes. The bending and tensile strength of edge-glued MDF were high with scarf, finger and butt joint, in order. The strength of finger jointed MDF showed 80% of scarf jointed MDF. The effects of location of finger joints on the bending strength of edge-glued MDF were larger than those of the numbers of finger joints. The bending strength of edge-glued MDF with one joint on the middle position showed 40% decrease in comparison with non-jointed MDF.

• Advances in nano research
• /
• 제9권2호
• /
• pp.91-104
• /
• 2020

The bending, stability (buckling) and vibration response of nano sized beams is presented in this study based on the Eringen's nonlocal elasticity theory in conjunction with the Euler-Bernoulli beam theory. For this purpose, the bending, buckling and vibration problem of Euler-Bernoulli nanobeams are developed and solved on the basis of nonlocal elasticity theory. The effects of various parameters such as nonlocal parameter e₀a, length of beam L, mode number n, distributed load q and cross-section on the bending, buckling and vibration behaviors of carbon nanotubes idealized as Euler-Bernoulli nanobeam is investigated. The transverse deflections, maximum transverse deflections, vibrational frequency and buckling load values of carbon nanotubes are given in tables and graphs.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2071-2081
• /
• 1995

In order to examine the effects of yield stress, tensile strength and thickness on the buckling behavior during bending of pipes, the nonlinear finite element analysis of the 3-point bending tests was carried out using the commercial software (ABAQUS) under the condition of L4(2$^{3}$) performed according to the designed condition. Form the analysis of simulation results, it was found that yield stress and thickness were the major factors on buckling load at pipe bending and tensile strength gave little influence because the plastic strain and plastic zone are small. For the punch displacement to the occurrence of buckling, thickness is a major factor and yield stress and tensile strength are the minor factors.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.951-965
• /
• 2014

Point bending is commonly used for cambering and curving steel girders to large radii. In this system, a hydraulic ram or press is used to apply concentrated loads at selected points to obtain the required vertical (cambering) or horizontal (curving) curved profile from induced permanent deformations. This paper derives closed form solutions that relate loads to permanent deformations for horizontally curving wide flange steel beams based on their post-yield response. These solutions are presented in a parametric form to identify the relationship between key variables and their impact on the accuracy of the curving operation. It is shown that point bending could yield parabolic curved profiles that are within 1% of a desired circular curve if the span length to radius of curvature ratio (L / R) is less than 1.5 and the point loads are spaced at one third the beam length. Safe limits are then established on loads, strains and curvatures to avoid damaging the steel section. This leads to optimization of the point bending operation for inducing a circular profile in wide flange steel beams of any size.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.438-439
• /
• 2007

In this study, we prepared ITO thin film on the polycarbonate(PC) substrate by using Facing Targets sputtering (FTS) system. After the external bending force was applied to as-deposited ITO thin films with fixed face-plate distance (L), we investigated how properties of those change. As a result, the crack density of films was increasing as bending frequency increased. In accordance with crack distribution, we observed that the resistivity value of ITO thin film increased.

• Steel and Composite Structures
• /
• 제37권4호
• /
• pp.405-418
• /
• 2020

The application of double-skin composite wall should meet different layout plans. However, most available research focused on the rectangular section with uniform axial compression. In this research, the structural behavior of double-skin composite wall with L section was studied. Due to the unsymmetric geometric characteristics, the considered loading condition combined the axial compression and biaxial bending. Five specimens were designed and tested under eccentric compression. The variables in the test included the width of the web wall, the truss spacing, the thickness of the steel faceplate, and the thickness of the web wall. The test results were discussed in terms of the load-displacement responses, buckling behavior, stiffness, ductility, strength utilization, strain distribution. Two modern codes were employed to predict the interaction between the axial compression and the biaxial bending. The method to calculate the available bending moment along the two directions was proposed. It was found that CECS 159:2004 offers more suitable results than AISC 360.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.181-184
• /
• 2003

In this paper, we investigated the position-dependent stress distribution of indium-tin-oxide (ITO) film on Polycarbonate (PC) substrate by external bending force. It was found that there are the maximum crack density at the center position and decreasing crack density as goes to the edge. In accordance with crack distribution, it was observed that the change of electrical resistivity of ITO islands is maximum at the center and decrease as goes to the edge. From the result that crack density is increasing at same island position as face-plate distance (L) decreases, it is evident that the more stress is imposed on same island position as L decreases.

• 한국강구조학회 논문집
• /
• 제11권2호통권39호
• /
• pp.131-142
• /
• 1999

뒤틀림 효과를 고려한 곡선보의 일반적 거동은 Vlasov에 의해 제시된 미분 방정식으로 표시된다. 일반적으로 거더의 단면을 결정하는데 가장 큰 영향을 미치는 요인은 휨모멘트이다. 곡선 교량 계획시 곡선격자형교의 단면을 쉽게 가정하기 위해서 본 논문에서는 직선거더와 곡선거더의 휨모멘트비를 제시하였다. 이 비는 중심각 ${\theta}(L/R)$를 변수로 하여 근사식으로 나타내었다. 이 휨모멘트 근사식과 제시된 영향선은 3경간 곡선격자형교를 보다 쉽게 설계하는데 이용될 수 있다.

• Elastomers and Composites
• /
• 제44권4호
• /
• pp.378-383
• /
• 2009

본 연구에서는 피라미드 형상의 코어재를 갖는 복합판재의 성형해석을 위한 축약모델의 사용이 제안되었다. L형 굽힘성형에 대하여 유한요소해석에 의한 해석을 수행하여 제안된 축약모델의 정확성과 유효성이 검증되었다. 성형해석의 정확성을 향상하기 위하여 코어의 보다 상세한 모델링과 코어성형에 의한 가공경화의 고려가 수행되었다. 변형형상과 성형하중곡선에 대하여 비교하였으며 실험과 좋은 일치를 보였다. 힘-하중 곡선의 비교에서 본 해석이 좌굴후변형거동을 잘 예측할 수 있음을 보였다.

• Computers and Concrete
• /
• 제14권1호
• /
• pp.1-18
• /
• 2014

The addition of steel fibers in concrete mixture is recognized as a non-conventional mass reinforcement scheme that improves the torsional, flexural, and shear behavior of structural members. However, the analysis of fiber reinforced concrete beams under combined torsion, bending, and shear is limited because of the complicated nature of the problem. Therefore, nonlinear 3D finite element analysis was conducted using the "ANSYS CivilFEM" program to investigate the behavior of fiber reinforced concrete L-beams. These beams were tested at different reinforcement schemes and loading conditions. The reinforcement case parameters were set as follows: reinforced with longitudinal reinforcement only and reinforced with steel bars and stirrups. All beams were tested under two different combined loading conditions, namely, torsion-to-shear ratio (T/V) = 545 mm (high eccentricity) and T/V = 145 mm (low eccentricity). Eight intermediate L-beams were constructed and tested in a laboratory under combined torsion, bending, and shear to validate the finite element model. Comparisons with the experimental data reveal that the program can accurately predict the behavior of L-beams under different reinforcement cases and combined loading ratios. The ANSYS model accurately predicted the loads and deformations for various types of reinforcements in L-beams and captured the concrete strains of these beams.