• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1302-1308
• /
• 2010

This study the change of the safety factor before and after the reinforcement were compared by performing the parameter research based on the limit equilibrium analysis regarding the same cross section after carrying out the safety factor before the reinforcement on the virtual section in order to observe the change of the safety factor of the slop reinforced with the slope planting reinforced earth, and the variation of the safety factor according to the increase of the length of the reinforcement materials and the change of the slope height was analyzed. As the result, the reinforcement effect was insignificant at no more than 0.6 of L/H, the reinforcement length ratio when the reinforcement length was increased, as the increase of the safety factor was slow comparing with the non-reinforced slope. At 3.0m of the slope height, reinforcement on the slope is not necessary, and at 3.0m to 5.0m of the slope height, the inclination was not influencing at no less than 0.6 of L/H. At 5.0m to 9.0m of the slope height, the safety factor was mostly secured on the slope at 0.8 of L/H and the over-reinforced slope appeared at no less than 1.0 of L/H. Also, the safety factor increased as the slope height increases and the slope gets steeper till 0.8 of L/H, but the slope steepness affects more on the increase of the safety factor than the reinforcement material, as the reinforcing force by the reinforcement material became steady.

• 한국환경농학회지
• /
• 제28권2호
• /
• pp.113-124
• /
• 2009

Severe sediment-laden problem has been the hot issue in Korea. It was assumed that agricultural activities and landslides were the primary causes of these problems in watersheds. The USLE-based systems have been widely used in soil erosion studies. However the GIS-based USLE modeling system has limitation in USLE L factors. In this study, the SATEEC L module was developed to reflect the slope length segmentations in the fields. The SATEEC L module was applied to the study watershed to analyze the effects of using the SATEEC L module on estimated sediment. As shown in the comparisons between SATEEC estimated sediment with SWAT values, the SATEEC GA-SDR module derives the SDR with reasonably acceptable accuracies. However, it is worthy to note that the soil erosion using the SATEEC L module for the study watershed was lower than that without using the SATEEC L module by 25%, although the SATEEC estimated sediment values with and without using L module match the SWAT sediment values with similar accuracies. This is because the SATEEC GA-SDR module estimates lower SDR in case of greater soil erosion estimation without the L module and greater SDR in case of lower soil erosion estimation with the L module. This indicates that the SATEEC input parameters, especially L factor, need to be prepared with care for accurate estimation of SDR at a watershed scale and for accurate evaluation of BMPs in the watershed.

• 한국조경학회지
• /
• 제26권3호
• /
• pp.162-177
• /
• 1998

Conentionally, LS factor for the USLE suggested by Wischmeier has been computed manually on topographic maps based on one dimensional approach. But outcomes of the equation could be severely affected by the convergence and divergence of surface runoff at complex terrains. Thus the objective of this research are to develop a method to automatically compute LS factor based on the multiple flow algorithm, and to test the accuracy of this method by comparing outcomes of this method to previous measurements or estimations of soil erosion. The program for the automatic calculation of LS factor was developed by utilizing Fox Pro 4.5, and outcomes of the program is designed to input to IDRISI. The accuracy test of LS factor was carried out by comparing the actual measurements of soil loss at two test sites in and around of Suwon. The calculated volume of soil erosion at Buju mountain, Mokpo, was also compared to the outcome of a previous research based on the LS factor calculated by the conventional onedimensional approach. The outcomes of this research are as follows. First, the computed L based on the multiple flow algorithm for concae slopes are greater than those of convex slopes,. Second, the estimated soil loss based on this method at the test site in Mokpo is much greater than the outcomes based on the conventional one-dimensional approach. It can e concluded that the application of this automatic calculation method of LS factor can improve the accuracy of USLE and facilitate soil erosion prevention methods.

• 한국측량학회지
• /
• 제19권1호
• /
• pp.27-37
• /
• 2001

강우나 물의 유출에 의한 토양침식은 농업 생산성을 떨어뜨리고 목초지를 손상시키며, 물의 흐름을 방해하는 등의 각종 환경적인 문제를 야기시키고 있다. 환경에 대한 관심이 고조되는 시점에서 토양침식이 매우 중요한 위치를 차지하고 있지만 아직은 체계적인 자료의 정리와 분석이 이루어지지 못하고 있는 실정이다. 본 연구는 최근 부각되고 있는 GSIS를 활용하여 토양침식을 예측하는 모형에 입력되는 인자를 추출하는 기법을 제시하는 것으로 침식모형에는 ANSWER, WEPP RUSLE 등 여러 가지가 있으나 본 연구에서는 GSIS 자료와의 연계가 용이하면서 유역에 대한 일반적인 토양침식을 예측할 수 있는 RUSLE 침식모형을 사용하였다. RUSLE 입력인자에는 강우침식인자 R, 토양침식인자 K, 침식사면의 길이인자 L, 침식사면의 경사인자 S, 식생피복인자 C 그리고 경작인자 P로 구성되어 있다. RUSLE 입력인자 중 L과 S인자 추출에 사용되었던 기존의 식은 대부분 농업지역에 적용된 식으로 유역에 적용시 한계가 있기 때문에 본 연구에서는 GSIS 자료를 통해 격자별로 유역에 적용 가능한 수정된 경험식을 활용하였다. 또한 격자형 RUSLE인자를 유역추출 알고리즘을 이용하여 유역별로 분석함으로서 유역별 RUSLE인자의 최소값, 최대값, 평균 그리고 표준편차를 계산할 수 있었다.

• Geomechanics and Engineering
• /
• 제21권5호
• /
• pp.401-411
• /
• 2020

The paper describes the influence of pile reinforcement on the stability of the slope behaviour, and the exploitation of the results of in situ measurements will be conducted. In the second part, a 2D numerical modelling will be conducted by using the finite element code PLAXIS2D; in order to validate the proposed modelling approach by comparing the numerical results with the measurements results carried out on the slides studied; to study the effect of positioning of piles as a function of the shear parameters of the supported soil on the behaviour of the soil. For various shear strength of the soil a row of pile position is found, at which the piles offer the maximum contribution to slope stability. The position of piles is found to influence the safety factor in granular soil whereas it shows a slight influence on the safety factor in coherent soil. The results also indicate that the ideal position for such stabilizing piles is in the middle height of the slope. Comparison of results of present study with literature from publication: indicated that to reach the maximum stability of slope, the pile must be installed with L_x/L ratio (0.37 to 0.62) and the inclination must be between 30° to 60°. Even, after a certain length of the pile, the increasing will be useless. The application of the present approach to such a problem is located at the section of PK 210+480 to 210+800 of the Algerian East-West Highway.

• Geomechanics and Engineering
• /
• 제32권5호
• /
• pp.523-540
• /
• 2023

The failure of slope can cause remarkable damage to either human life or infrastructures. Stabilizing piles are widely utilized to reinforce slope as a slip-resistance structure. The workability of pile-stabilized slopes is affected by various parameters. In this study, the performance of earth slope reinforced with piles and the behavior of piles under static load, by shear reduction strength method using the finite difference software (FLAC^3D) has been investigated. Parametric studies were conducted to investigate the role of pile length (L), different pile distances from each other (S/D), pile head conditions (free and fixed head condition), the effect of sand density (loose, medium, and high-density soil) on the pile behavior, and the performance of pile-stabilized slopes. The performance of the stabilized slopes was analyzed by evaluating the factor of safety, lateral displacement and bending moment of piles, and critical slip mechanism. The results depict that as L increased and S/D reduced, the performance of slopes stabilized with pile gets better by raising the soil density. The greater the amount of bending moment at the shallow depths of the pile in the fixed pile head indicates the effect of the inertial force due to the structure on the pile performance.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.303-308
• /
• 2003

In this paper, wave numerical modeling was experimented for the analysis of impact factors for the wave transmission as the incident wave and topographic conditions in the narrow channel sea. Recently, Although the results of many researcher for the wave modelling, numerical equations have limited to simulation of wave transformation effects. Despite of thispresent problems, the models was used to design the coastal structures in barrow channel sites. Finally, this paper estimated the wave model(mild slope eq. model) as the analysis of the wave energy transmission according to changing of impact factors(width of channel, bottom slope in channel, incident wave angle, wave period). As the results of numerical experiment, the major impact factors which influence to wave energy transmission were the width of channel and incident wave direction. But in the case that the width of channel is larger than 3L(L=Length of wave), the reduction of wave energy was small.

• 한국물환경학회지
• /
• 제36권5호
• /
• pp.385-391
• /
• 2020

Soil loss is a serious problem frequently caused by local torrential rainfalls due to climate change. In particular, soil loss is occurring in agricultural areas rather than urban areas, and many pollutants are introduced into rivers, causing environmental problems. To reduce soil loss, the Ministry of Environment has designated and managed non-point source management areas. The Jaun-district in Hongcheon-gun, which was designed as a non-point pollution source management area in Gangwon-do, is located in the upper stream of Soyang Lake. Most of the agricultural fields are composed of highland agriculture fields. The highland agricultural fields in the Jaun-district are also composed of large-scale farming areas, and the ditches located near the agricultural fields have been illegally used for farmland. Therefore, the local government in Hongcheon-gun is conducting a project to restore the ditches occupied by agricultural fields. However, an analysis of the amount of soil loss that can be reduced by the restoration of the ditches has not been conducted yet. Thus, the purpose of this study was to analyze the effect of reducing the soil loss from the restoration of the ditches used as agricultural fields in the Jaun-district. The SATEEC L Module was used to analyze the reduction in soil loss by ditch restoration. The SATEEC L Module was constructed to estimate the LS factor using Moore and Burch's method after calculating the slope length using the digital elevation model and the maximum allowable slope length. The LS factor and the USLE formula were used to estimate the amount of soil loss that could be reduced by ditch restoration. The analysis showed that the ditch restoration could reduce about 16.6% of the soil loss in the Jaun-district. The results of this study will contribute to the study of methods to reduce soil loss in non-point pollution management areas.

• 한국지반환경공학회 논문집
• /
• 제19권12호
• /
• pp.5-14
• /
• 2018

최근 국내에 사용되고 있는 보강토옹벽 공법은 전면체의 재질, 보강재, 축조방법, 축조경사에 따라 수많은 종류가 제안되었으나 각 공법에 따른 설계방법이나 상세검토항목 등의 규정이 명확하지 않으며 집중호우에 따른 붕괴도 빈번하게 발생하고 있는 실정이다. 본 연구에서는 이러한 보강토옹벽의 설계에 있어서 좀 더 안정된 기술적 접근을 위해 설치높이별 단면을 가정하고 단일 강도의 보강재를 사용한 보강토옹벽의 인발파괴와 높이별 최적의 보강재 조합을 산정하고 산정된 각 단면에 대해서 보강길이비(L/H)에 따른 안전율 변화를 통하여 보강재의 최적 설계와 다단식 보강토옹벽의 최적 설계 그리고 보강재인 토목섬유의 재질에 따른 최적 길이비를 산정하여 제시하였다.

• 한국환경생태학회지
• /
• 제34권5호
• /
• pp.402-412
• /
• 2020

본 연구는 울산권 4개 용수댐에서 서식하고 있는 어류상과 생태계교란 생물로 지정된 블루길에 대한 개체군 특성을 파악하고 기초자료를 제공하는데 목적을 가지고 시행되었다. 울산권 4개 용수댐 및 주변지류에 서식하는 어류를 대상으로 2016년부터 2017년까지 연구를 실시한 결과, 총 9과 28종 1937개체가 확인되었으며, 한국고유종은 6종(고유화율 21.4%), 외래종 4종, 생태계교란 생물 2종이 조사되었다. 본 연구에서 확인된 어류의 개체수를 기준으로 우점종 및 아우점종을 확인한 결과, 우점종은 블루길, 아우점종은 치리로 확인되었다. 블루길 개체군의 연령구조를 조사한 결과, 울산권 4개 용수댐은 만 1~2년생의 개체군이 많이 확인되었으며, 개체군이 빠르게 성장하고 있는 단계로 판단된다. 또한, 블루길 개체군의 전장-체중 관계식 및 비만도를 분석한 결과, 울산권 4개 용수댐의 전장-체장 관계식은 회귀계수 b값이 3.0보다 크게 나타났으며, 블루길 개체군이 서식상태가 양호한 것으로 판단된다. 비만도는 기울기 값이 양의 값을 보이며, 성장상태가 비교적 양호한 것으로 나타났다. 본 연구결과는 울산권 4개 용수댐에 서식하는 블루길 개체군의 동향 예측을 파악하는데 유용한 자료로 활용될 것으로 본다.