• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.4
• /
• pp.355-365
• /
• 2015

This study examined the fluidity and strength properties, water resistance, durability, and freeze-thaw of cementless loess mortar using an eco-friendly hardening agent. The experimental result indicates that 28 days compressive and flexural strength of the loess mortar was increased regardless of the weathered granite soil and loess mixture ratio as the replacement ratio of the hardening agent increases. The strengths were significantly increased until 14 days regardless of the hardening agent, while the effect on the strengths increasement was relatively low after 14 days. Thus, the strength development of loess mortar concrete was found to be faster than that of the normal concrete. In addition, when the hardening agent of 10% was used, the average flexural strength was 1.7MPa which is insufficient compared to the 28-day flexural strength of 4.5MPa for the paving concrete. However, the flexural strengths of the loess mortar concrete using the hardening agents of 20% and 30% were 4.0MPa and 5.3MPa, respectively. Thus, the hardening agent need to be at least 20% so that the loess mortar can be used for paving concrete. The experiment for water resistance shows that the repeated absorption and dry reduced mass regardless of the mixing ratio of the loess. The maximum length change also decreased with increasing the substitution rate loess mixture ratio and the hardening agent. The result of the freeze-thaw resistance test indicates that the relative dynamic modulus of elasticity at 300 cycle freeze-thaw with the hardening agents of 20% and 30% were 75% and 79%, relatively. Thus, the hardening agent of at least 20% is required to obtain the relative dynamic modulus of elasticity of 60% for the loess mortar.

• Korean Journal of Ecology and Environment
• /
• v.40 no.4
• /
• pp.537-545
• /
• 2007

The heavy metal removal capacity of filamentous green alga Cladophora sp. cultured together with wet-mixed solidified soil (loess) was tested. A Cladophora sp. was cultured for 5d, with added Chu No. 10 medium, in stream water contaminated by high concentration of heavy metals from a closed mine effluent. Heavy metal ion concentrations of the medium and in algal tissue were measured every day during the experiment. Dissolved metals (Al, Cd, Cu, Fe, Mn, Zn) in medium were rapidly removed (over 90% elimination) within 1-2d when alga and loess were added. Dissolved heavy metals dropped by only 10% when algae were cultured without loess. The Cladophora sp. accumulated much more heavy metals when cultured with loess than when the alga was cultured alone. Cladophora sp. exhibited a maximum uptake capacity for Al ($17,000{\mu}g^{-1}$ algal dry weight). The metal bioremoval capacities of the algae were in the order Al, Fe, Cu, Mn, Zn and Cd. The heavy metal removal capacity of Cladophora sp. showed significant increases when wet-mixed solidified soil was added to culture media.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2471-2476
• /
• 2014

The aim of the present study is to explore the possibility of utilizing loess for the adsorption of total phosphorous (T-P) and total nitrogen (T-N) in water. Batch adsorption studies were performed to evaluate the influences of various factors like initial concentration, contact time and temperature on the adsorption of T-P and T-N. The adsorption data showed that loess is not effective for the adsorption of T-N. However, loess exhibited much higher adsorption capacity for T-P. At concentration of $1.0mgL^{-1}$, approximately 97% of T-P adsorption was achieved by loess. The equilibrium data were fitted well to the Langmuir isotherm model. The pseudo-second-order kinetic model appeared to be the better-fitting model because it has higher $R^2$ compared with the pseudo-first-order and intra-particle kinetic model. The theoretical adsorption equilibrium $q_{e,cal}$ from pseudo-second-order kinetic model was relatively similar to the experimental adsorption equilibrium $q_{e,exp}$. The thermodynamic parameters such as free energy ${\Delta}G$, the enthalpy ${\Delta}H$ and the entropy ${\Delta}S$ were also calculated.

• Journal of Korean Society on Water Environment
• /
• v.31 no.5
• /
• pp.476-481
• /
• 2015

Water permeable block was manufactured using waste sewage sludge, loess and clay for the purpose of recycling waste sludge due to the prohibition of waste sludge ocean dumping. Experiments for determining optimum mixing ratio was conducted by changing sludge content in water permeable block as 5~20%. In respect of compressive strength, $1,600N/cm^2$ ($163.3kg/cm^2$) was obtained when the mixing ratio of sludge : loess : clay were maintained by 5% : 65% : 30%, 10% : 65% : 25% and 15% : 65% : 20%, respectively. These mean that relatively high compressive strength can be obtained when the sludge content is maintained 5, 10, 15% at the 65% of loess content. In terms of water permeability and absorption rate, the higher values can be obtained as the sludge content increases. The optimum mixing ratio of sludge : loess : clay came out to be 15% : 65% : 20% when water permeability, absorption and strength were considered altogether, which matches the result observed by an electron microscope. The heavy metal leaching test result of the prepared permeable block appeared to satisfy the environmental standard in the content of Cd, Cu, Pb and As.

• Textile Coloration and Finishing
• /
• v.18 no.4
• /
• pp.1-10
• /
• 2006

Tannin treatment has been used for improving the color fastness of dyed materials. In natural dyeing, the tannin treatment is highly effective in improving the fastness. The chitosan treatment also improves the fastness and depth of shade in natural dyeing. In this study, the effects of tannin and chitosan pre-treatment on the color and fastness in loess dyeing were investigated. Cotton woven fabric specimens and cotton knit fabric specimens were pre-treated with chitosan solution in acetic acid, and the specimens were then treated with or without tannin. The specimens were finally dyed with loess. The tannin treatment decreased the K/S values, while the chitosan treatment increased the K/S. Both the tannin treatment and the chitosan treatment increased the wash fastness and light fastness. In tannin treatment, tannin component and Fe component of loess may react together to decrease the lightness and develop dark color. For maintaining inherent color of the loess, it is much preferable to employ chitosan treatment rather than tannin treatment.

• Journal of Environmental Science International
• /
• v.8 no.4
• /
• pp.497-502
• /
• 1999

Removal of Pb(Ⅱ), Cu(Ⅱ), Cr(Ⅲ), and Zn(Ⅱ) ions from aqueous solutions using the adsorption process on domestic loess minerals has been investigated. Variations of contact time, pH, adsorption isotherms and selectivity of coexisting ions and leachate were experimental parameters. YDI, YPT and KRT samples diluted in 1% aquous solution which was adjusted pH 10.8, 8.0 and 6.50, respectively. The result of XRD measurement, Quartz was mainly observed in all samples. In the case of KRT sample, Kaolinite, Feldspar, Chlorite consisting of clay minerals shows almost same pattern with YPT samples. Different properties showed from the YDI sample containing Iillite, remarkably. For all the metals, maximum adsorption was observed at 30min∼60min. Adsorption of metal ions on loess minerals were reached an equilibrium by shaking the solution for about 30min. Removal efficiency of Pb(Ⅱ) ion for KRT, YPT and YDI were 84.7%, 92% and 100%, respectively. The Cu(Ⅱ) and Zn(Ⅱ) adsorptivity on KRT showed the low in various pH solution However, those on YPT and YDI were high than 90% except for the pH 2 solution. The orders of adsorptivities for domestic loess minerals showed as following : YPT>KRT>YDI. The adsorption isotherms of Cu(Ⅱ) and Zn(Ⅱ) ions on clay minerals were fitted to a Freundlich's. Freundlich constants(1/n) of KRT and YPT domestic loess minerals were 0.63, 0.97 and 0.36, 0.25, respectively.

• ALGAE
• /
• v.22 no.2
• /
• pp.141-146
• /
• 2007

Seagrass bed is an important component in coastal and estuarine ecosystems, providing food and habitats to a wide variety of marine organisms. Recently, seagrass coverage has declined significantly due to anthropogenic impacts such as cultural eutrophication and reclamation, and thus efforts are under way to prevent further losses and restore disturbed seagrass habitats worldwide. Seagrass transplantation techniques for habitat restoration include vegetative and seed-based methods. Seagrass seeds can be collected easily, and sowing seeds is an economically effective method for large-scale restoration. However, large numbers of seed can be lost by seed predation and physical disturbance in the planting areas. In the present study, Zostera marina seeds were coated with loess to reduce seed loss by predation and sweeping away by the water currents, and germination rates of coated seeds and seedling growth were examined to assess the feasibility of the seed-coating method for large-scale restoration. Germination rate of the coated seeds with loess was significantly higher than that of the uncoated seeds. Additionally, seedling growths were not significantly different between the coated and the uncoated seeds. These results suggest that coating of eelgrass seeds with loess enhances success of seed germintion with no harmful effects on seedling growth. Therefore, the seed coating method using loess may be an effective and applicable seedbased transplanting technique for large-scale restoration.

• Journal of environmental and Sanitary engineering
• /
• v.13 no.1
• /
• pp.57-68
• /
• 1998

This study was surveyed to examine the removable ability of residual aluminum with the coagulants(LAS, PAC) and the auxiliary coagulants(Loess, R-calmont) on raw water. The leaching test of the auxiliary coagulant showed that the loess contained a lot of Al, Fe and Mn. On the reverse, the R-calmont was a little. Most of the loess were composed of $SiO_{2}$ 53.25%, $Al_{2}O_{3}$ 29.28%, $Fe_{2}O_{3}$ 10.73% and Si/Al ratio was 3.08. In using both LAS vs. loess and PAC vs. loess as the coagulated material, the removal of residual aluminum was the highest as 96.3%, 96.6% respectively, and that of the residual turbidity was 95.0% when PAC vs. R-calmont was dosed 0.2mg/L. Also, loess showed better than R-calmont in the removable efficiency of aluminum and turbidity. When the setting time of auxiliary coagulant was input ar the same time with coagulant, the removal aluminum was the highest as 93.3% to 96.6%.

• Journal of environmental and Sanitary engineering
• /
• v.12 no.3
• /
• pp.127-130
• /
• 1997

The removal of algae was conducted by loess, aluminum sulfate and PAC on a laboratory scale. The loess was consists of organic matter 1.4%, T-N $289{\mu}g/g$, T-P $17{\mu}g/g$, $Al841.2{\mu} g/g$, Fe $592.7{\mu}g/g$, Ca $10.6{\mu}g/g$, Mg $85.5{\mu}g/g$ and Mn $6.6{\mu}g/g$. Test water was dominated by Microcystis aeruginosa. When test water was mixed with 0.01, 0.05. and 0.1 g/$\ell$ of the loess in 5 minutes, after settled in 1 hour, the removal of chl-a was 2, 22, and 36% respectively. The removal of chl-a was 69%, 70% in pH 4.5 and 9.0 and above 92% between pH 5.0 and 8.0 after the $2mg/{\ell}$ of aluminum sulfate was added. When the $2mg/{\ell}$ of PAC and $0.05g/{\ell}$ of loess were added to test water together, the removal of chl-a was 95-99% in pH 4.0-8.0, 60% in pH 9.0, and 18% in pH 10.0. The removal of chl-a was higher when loess, aluminum sulfate and PAC was used together than used alone.

• Korean Journal of Organic Agriculture
• /
• v.25 no.2
• /
• pp.345-355
• /
• 2017

This study was conducted to evaluate rice seed disinfection efficacy of loess-sulfur for the suppression of Bakanae disease caused by Fusarium fujikuroi. Rice seeds were treated at different concentrations of loess-sulfur, soaking time and temperature, and combination of hot-water treatment. Rice cultivar, Shindongjin harvested from Bakanae disease-infested area in 2015, was used. Loess-sulfur was treated as follows; concentration of undiluted solution, 2%, 1% and 0.5%; soaking time of 24 and 48 hours; treatment temperature of $20^{\circ}C$ and $30^{\circ}C$; hot water treatment or not. Optimal conditions of rice seed disinfection were selected soaking time of 48 hours and the suspension of 0.5% and 1% loess-sulfur by investigating seed germination and isolation frequency of Fusarium spp. on Komada agar medium in vitro, and were established 3 disinfection conditions as hot water ($60^{\circ}C$, 10 min.) + 1% loess-sulfur ($20^{\circ}C$, 48 hours), 1% loess-sulfur only ($30^{\circ}C$, 48 hours) and 1% loess-sulfur only ($20^{\circ}C$, 48 hours) through additional test in greenhouse. Above 3 conditions were verified by rice seedling box and paddy field test in the way of investigating Bakanae diseased plants (%) and healthy plants (%). Consequently, most effective rice seed disinfection conditions on Bakanae disease were combination of hot water and 1% loess-sulfur and loess-sulfur only at $30^{\circ}C$. Furthermore, treatments with these conditions showed control value of 100% were maintained from seedling to the heading stage in the field. However, treatment of 1% loess-sulfur only at $20^{\circ}C$ showed low control value of 78.2% in paddy field. Hot water only treatment turned out to be an effective disinfection method when conducted thoroughly with $60^{\circ}C$, 10 min. However, it was thought additional soaking process with loess-sulfur after hot water treatment served more high control effect against Bakanae disease when rice seeds were disinfected on a large scale. This results expected rice seed disinfection with loess-sulfur were effectively and easily usable method if farmers had only one of either hot water-disinfector or seed-disinfector. In addition, loess-sulfur is well-known to farmers, simple to manufacture method and cheap.