• Journal of the Korean earth science society
• /
• v.25 no.1
• /
• pp.22-31
• /
• 2004

Laboratory experiments were conducted in order to find effects of the intermediate principal stress of ${\sigma}_{2}$ on rock fractures and faults. Polyaxial tests were carried out under the most generalized compressive stress conditions, in which different magnitudes of the least and intermediate principal stresses ${\sigma}_{3}$ and ${\sigma}_{2}$ were maintained constant, and the maximum stress ${\sigma}_{1}$, was increased to failure. Two crystalline rocks (Westerly granite and KTB amphibolite) exhibited similar mechanical behavior, much of which is neglected in conventional triaxial compression tests in which ${\sigma}_{2}$ = ${\sigma}_{3}$. Compressive rock failure took the form of a main shear fracture, or fault, steeply dipping in ${\sigma}_{3}$ direction with its strike aligned with ${\sigma}_{2}$ direction. Rock strength rose significantly with the magnitude of ${\sigma}_{2}$, suggesting that the commonly used Mohr-type failure criteria, which ignore the ${\sigma}_{2}$ effect, predict only the lower limit of rock strength for a given ${\sigma}_{3}$ level. The true triaxial failure criterion for each of the crystalline rocks can be expressed as the octahedral shear stress at failure as a function of the mean normal stress acting on the fault plane. It is found that the onset of dilatancy increases considerably for higher ${\sigma}_{2}$. Thus, ${\sigma}_{2}$ extends the elastic range for a given ${\sigma}_{3}$ and, hence, retards the onset of the failure process. SEM inspection of the micromechanics leading to specimen failure showed a multitude of stress-induced microcracks localized on both sides of the through-going fault. Microcracks gradually align themselves with the ${\sigma}_{1}$-${\sigma}_{2}$ plane as the magnitude of ${\sigma}_{2}$ is raised.

• Journal of the Korean earth science society
• /
• v.29 no.7
• /
• pp.551-558
• /
• 2008

The Soowang deposits occur in the quartz veins that were filled fissures in the middle Cretaceous porphyritic granite and/or the Precambrian Sobaegsan gneiss complex. Paragenetic studies suggest that the vein filling can be divided into four identifiable stages. Sphalerites were deposited by the cooling fluids at stages I, II, and III. The results of microscopic observation and EPMA analysis suggest that the chalcopyrite dots and disease in sphalerite are replacement products by later hydrothermal solution at the early stage III. The inferred processes of chalcopyrite disease are as follows: (1) Fe enrichment to the margins and along the cracks of the Fe-poor sphalerite by Fe-rich solution, (2) Formation of chalcopyrite dots in the Fe-enriched sphalerite formed at the stage II, and Fe reduction of sphalerite near the chalcopyrite dots by Cu-bearing solution, (3) Formation of "chalcopyrite disease" penetrating the compositional zoning of sphalerite at the early stage III.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.8
• /
• pp.65-73
• /
• 2012

Soil-rock interface, mainly founded in Granite region of Korea, is known as one of the important factor of the slope failure at the rainfall due to smaller shear strength than soil itself. However, research of the effect on slope stability by soil-rock interfaces is insufficient. Therefore, a series of direct shear tests were performed in order to investigate the effect of soil-rock interface on slope stability. The method of tests is to get sand itself and sand-artificial rock interface shear strength from different grain size of sands and artificial rock samples. The results of tests show that the friction angle of interface depends primarily on particle size and surface roughness. Interface friction angle ratio ${\mu}(={\delta}/{\Phi})$ is in the range of 0.75 ~ 0.96, this results indicate that interface friction angle is smaller than sand itself.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.1
• /
• pp.49-55
• /
• 2007

In order to utilize treads of waste tire as reinforcement material it is necessary to know the interface friction angle between tread surfaces and soil and tensile strength of connection joint of tire treads. In this research large direct shear tests were performed to get the interface friction angle between the inner and outer surfaces of treads and soil for different degree of compaction. From the large direct shear tests, the ratio of interface friction angle to the shear friction angle of sand, ${\delta}/{\phi}$, were 1.06 in outside surface of tire tread and 0.93 in inside surface of tire tread. For weathered granite soil the ratio of interface friction angle was 0.98 and 0.92 for outside and inside of tread, respectively. Also tensile tests were performed using universal testing machine for the connection joint of treads and Tirecell units using bolts. The tensile strength of connection joint increased with the number of bolts and with the sizes of washers. Connection by polypropylene ropes showed lower strength than those of bolts.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.1
• /
• pp.43-52
• /
• 2004

Laboratory model tests were conducted to assess the behavior characteristics of geogrid reinforced earth walls using fiber-mixed soil backfill with different surcharge loads and reinforcement spacing. The models were built in the box having dimensions, 100cm tall, 140cm long, and 100cm wide. The reinforcements used were geonet(tensile strength, 0.79t/m) and geogrid(tensile strength, 2.26t/m). Decomposed granite soil(ML) with or without polypropylene fiber was used backfill material. Strain gauges and LVDTs were installed on the retaining walls to measure the strain of the reinforcements and the displacements of the wall facings.

• Economic and Environmental Geology
• /
• v.25 no.2
• /
• pp.167-177
• /
• 1992

The gravity measurement has been conducted at 53 and 34 stations with an interval of 1~1.5 km along the national roads of about 47 km and 34 km running from Duksungri to Yangpori and from Angangri to Byungpori, Kyungsangbookdo, respectively. The subsurface geology and geologic structure of Tertiary Pohang and Janggi basins along two survey lines are interpreted quantitatively by applying Fourier series and Talwani methods for Bouguer gravity anomaly. The depths of Conrad discontinuity vary from 11.8 to 12.5 km and 11.5 to 13.2 km along the survey lines between Duksungri and Yangpori, and Angangri and Byungpori, respectively. The depths of pre-Cambrian Gneiss complex underneath Kyungsang Supergroup vary from 3.8 to 4.2 km and 3.8 to 4.6 km along the survey lines between Duksungri and Yangpori, and Angangri and Byungpori, respectively. Massive granite bodies which are not exposed along the survey line between Duksungri and Yangpori are distributed on a large scale at the subsurface between Duksungri and Ochun, and Daegokri and Yangpori. Along the survey line between Angangri and Byungpori, it is exposed at Angangri, and extends underneath Chungrimdong, Pohang city. Andesite is distributed on a small scale underneath Pohang city and Ochun. The thicknesses of Tertiary Yonil and Janggi Groups are 0.2~0.9 km and 0.1~0.5 km, respectively. The Tuffaceous rocks which are the lowest formation of Tertiary sedimentary rocks are distributed with the thickness of 0.2 km at the surface and between Kyungsang Supergroup and Yonil or Janggi Groups. The Yonil and Janggi Groups are in fault contact by a fault running through Ochun and Chungrimdong, Pohang city. Two other faults are newly found near Heunghae-eup and Hyungsan river.

• Economic and Environmental Geology
• /
• v.29 no.6
• /
• pp.753-765
• /
• 1996

It is a well known fact that the remanent magnetization direction of the Tertiary rocks is deflected significantly clockwise (about $50^{\circ}$) in the Tertiary basins of the southeastern part of Korean peninsula. This fact has been interpreted as an evidence of north-south spreading of the East Sea (Sea of Japan) and dextral strike-slip motion of the Yangsan fault. As deflection (rotation) of remanent magnetizations is frequently reported from various regions of the world in the vicinities of strike-slip fault, such phenomena are to be expected in the Yangsan fault region also. It was the purpose of this study to clarify whether such premise is right or not. A total of 445 independently oriented core samples were collected from Cretaceous rocks of various lithology (sedimentary rocks, andesites and I-type granites) in the Yangsan fault area. In spite of through AF and thermal demagnetization experiments, no sign of remanent magnetization deflection was found. Instead, palaeomagnetic poles calculated from formation-mean ChRM directions are very similar to those of contemporary (Barremian, and late Cretaceous-Tertiary) sedimentary and plutonic rocks in the other parts of $Ky{\check{o}}ngsang$ basin as well as those of China. Therefore, possibility of tilting of granite plutons and horizontal block rotation of study area is excluded. It is also concluded that the Yangsan fault did not take any significant role in the Cenozoic tectonic evolution of southeast Korea and the East Sea region. The boundary between rotated and unrotated region of remanent magnetization is not the Yangsan fault line, but must lie further east of it.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.9
• /
• pp.45-55
• /
• 2020

X-ray computed tomography (CT) is very useful for the quantitative evaluation of internal structures, particularly defects in rock samples, such as pores and fractures. In situ CT allows 3D imaging of a sample subjected to various external treatments such as loading and therefore enables observation of changes that occur during the loading process. We reviewed state-of-the-art of in situ CT applications for geomaterials. Two triaxial cells made using relatively low density but high strength materials were developed aimed at in situ CT scanning during hydro-mechanical laboratory testing of rocks. Preliminary results for in situ CT imaging of granite and sandstone samples with diameters ranging from 25 mm to 50 mm show a resolution range of 34~105 ㎛ per pixel pitch, indicating the feasibility of in situ CT observations for internal structural changes in rocks at the micrometer scale. Potassium iodide solution was found to improve the image contrast, and can be used as an injection fluid for hydro-mechanical testing combined with in situ CT scanning.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.1
• /
• pp.15-21
• /
• 2005

In this study, the utilization of coal-ash and phosphogypsum was considered as the evapotranspiration final landfill cover(ET cover) material. Cover material considered was the mixture of the weathered granite soil, coal-ash and phosphogypsum and so we sequentially performed the leaching test, column test and field model test to investigate the environmental effects of mixtures of coal-ash and phosphogypsum. In the leaching test, all materials had lower heavy metal concentration than the regulated threshold values. The column test and the review of related regulations were carried out to determine the optimum mixing ratio(OMR) and OMR was soil(4):coal-ash(1): phosphogypsum(1) on the volume base, which was applied to field model test. Field model tests were continued from February to June, 2004 in the soil box that was constructed with cement block. It was verified that coal-ash and phospogypsum mixed with soil was safe environmentally and the mixture of both wastes could improve the water retention capacity of cover materials.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.5
• /
• pp.17-25
• /
• 2016

The rocks exposed on the surface undergo expedite weathering process due to the effects of climatic process, etc. and the weathering process changes the properties of minerals, thereby lowering the stability of rocks. Therefore, it is important to examine the composition of minerals in order to investigate the resistance of rocks against weathering, which is performed by weathering sensitivity analysis. And microscopic flaking test was performed for the bored samples in this study and the composition of minerals that are vulnerable to weathering was measured through mode analysis. The lithological and mineralogical weathering factors were evaluated through this process. Furthermore, the degree of progress of weathering was identified by quantitatively measuring the actual mineral composition of rocks through X-Ray diffraction analysis and identifying the secondary minerals through observation with a scanning electron microscope. This analyzing the weathering sensitivity was analyzed to be capable of determining appropriate indicators that can determine weather resistance and predicting the weathering grade using chemical weathering speed.