• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1051-1060
• /
• 2008

The use of the coal ash for surcharge material, in a view of the environmental aspect, can decrease amount of the reclamation through recycling waste materials as well as prevent a destruction of the ecosystem attributed to sand picking. In addition, it can reduce both unit cost of material and construction expenses. In this study, new construction material as alternative surcharge material using coal ash, which is by-product from thermoelectric power plant, were developed. Mixing ratios of fly ash and bottom ash derived from the coal ash in Samchunpo thermoelectric power plants were determined. Furthermore, mixing conditions depending on the ratios of the cement and gypsum used for chemical additive were determined too. Uniaxial compression strength tests were conducted at different mixing conditions and Design graph of optimum mixing ratio at each required strength for economic efficiency is indicated in this paper.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.67-70
• /
• 2007

In this study, the characteristic of strength development of high volume fly ash concrete(HVFAC) was experimentally investigated. The production of one ton of portland cement releases about 0.87ton of CO2 into the atmosphere. HVFAC is an emerging material technology and is environmentally friendly because of its reduced use of portland cement, reduced CO2 emissions. For this purpose, two levels of W/B were selected. Seven levels of fly ash replacement ratios and two levels of silica fume replacement ratios were adopted. In the concrete mix, the water content of 125kg/m3 was used, which is less than that of usual water content. As a result, it was observed that the slump of concrete was increased with the increasing fly ash replacement ratio and when the silica fume was incorporated into the concrete, the slump was significantly decreased at the same condition. It appeared that the compressive strength gradually decreased with increasing fly ash replacement ratio at the early age, but the difference of strength up to replacement ratio of 50% was little at the age of 91 days because of the pozzolanic reaction of fly ash.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.3
• /
• pp.81-90
• /
• 1999

The purpose of this study is to examine the uses of fly ash asa type of construction material. This paper presents the results of research performed to identify optimum mix proportions for production of lowable fill with high volume fly ash content . The fly ash used in this study met the requirements of KS L 5405 and ASTM C 618 for Class F material. The flowable fill with high volume fly ash content was investigated for strength and flowability characteristics. Tests were carried out on flowable fill designed to have 10 ~15kgf/$\textrm{cm}^2$ compressive strength at 28 days with fly ash contents of approximately 260kgf/㎥. Slump was held at 25$\pm$1cm for all mixtures produced to range from 5kgf/$\textrm{cm}^2$ to 14kgf/$\textrm{cm}^2$ compressive strengths at 28 days. To produce flowable fill with high volume fly ash , first the influential variables were identified in an experimental study based on factorial design. Among the proportioning variables investigated, cement ,fly ash, and sand contents were found to have statistically significant effect on strength and slump of flowable fill . Subsequently, response surface analysis techniques were used to devise an experimental program that helped determine the optimum combinations of the selected influential variables based on material properties and cost. The optimized flowable fill were then technically evaluated. It is shown that flowable fill has acceptable compressive strength , slump flow, hardening time, and permeability.

• Journal of Environmental Science International
• /
• v.12 no.7
• /
• pp.783-789
• /
• 2003

This study was conducted to reuse the rice straw ash as washing agent for oil contaminated soils. The results are summarized as follows. The physical characteristics of rice straw before and after burning were as follows ; In case of burning rice straw 1g, the rice straw ash was generated 0.14g and pH was changed neutrality into alkali(pH 10.9) and specific surface area was increased to five times and particle distribution was corresponded to fine silt.(under 0.05mm) The physical characteristics of rice straw ash were Carbon 10.9%, Hydrogen 1.5%, Oxygen 23.4%, Nitrogen 5.2%, Sulfate 1.2% and chemical characteristics were Si 189.2ppm, Ca 10.2ppm, Mg 4.7ppm. Oil cleanup ratio by pH variation were about 40∼50% of initial concentration of oil by pH 10∼11. As the result of cleanup comparative experiment, the rice straw ash was about 20∼30%, the tritonX-100 about 40∼50% of washing efficiency, and then in the future it will be possibility of substitute washing agent.

• Journal of Environmental Science International
• /
• v.5 no.6
• /
• pp.785-799
• /
• 1996

The incineration tests of mixed industrial wastes using the stoker type incinerator are carried out to investigate the partitioning characteristics of heavy metals during incineration. The results obtained from this study are as follow. The partitioning characteristics of heavy metals throughout this incinerator are found that, at given condition of $700^{\circ}C$, the elements with the relatively high boiling point such as Cr, Cu and Pb are partitioned into a bottom ash, a fry ash captured tv cyclone, and a flue gas stream, 67~88%, 2~19% and 6~16% of initial amount entering the incinerator, respectively, but the Cd and Hg of 75~81% is vaporized into the flue gas. It appears that the partitioning characteristics according to the particle size of ash is different between the bottom ash and the fly ash. For bottom ash, the fraction of partitioning into 75${\mu}{\textrm}{m}$ oversized particles is reatively high. For fly ash, the characteristics of distributions with the particle size can not be clearly shown.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.650-654
• /
• 2001

To utilize municipal solid waste incineration ash as useful resources in Korea, studies on the present state of production and management of incineration ash and its effects on environment were made. And, it was intended to analyze the management conditions of incineration ash in many foreign countries and reflect them in domestic incineration ash policy. Korean incineration ash policy is based on the control of waste production, considering the difficulties in securing landfills and the small size of national land, and will be changed into recycling- and incineration-centered one. Furthermore, studies on the stabilization and recycling of incineration ash should be continuously conducted to overcome the concerns about environmental pollution.

• 한국연소학회:학술대회논문집
• /
• 1995.06a
• /
• pp.91-103
• /
• 1995

In recent years, significant advances have been made in the development of methods to predict ash behavior in utility boilers. This paper provides an overview of methods used to assess and predict ash formation and deposition. It has discussed some of the key problems associated with the formation and deposition of ash during the combustion of pulverized coal. Although considerable progress has been made in understanding of the fundamental mechanisms of ash formation, transport, growth, and strength development, there is still much work to be done. There is a need to develop quantitative relationships between the characteristics of the entrained ash and the physical properties of ash deposits that influence deposit growth, strength development, and cleanability. Also data from bench-scale, pilot-scale, and full-scale units are needed in order to determine operating conditions which will minimize deposition problems, maximize efficiency, and reduce emissions.

• Journal of Environmental Science International
• /
• v.19 no.1
• /
• pp.105-114
• /
• 2010

The objective of the paper is to experimentally investigate the compressive strength of the concrete incorporating fly ash. Ordinary Portland cement(OPC). Water to binder ratio(W/B) ranging from 30% to 60% and curing temperature ranging from $-10^{\circ}{\sim}65^{\circ}C$ were also adopted for experimental parameters. Fly ash was replaced by 30% of cement contents. According to the results, strength development of concrete contained with fly ash is lower than that of plain concrete in low temperature at early age and maturity. In high curing temperature, the concrete with fly ash has higher strength development than that of low temperature regardless of the elapse of age and maturity. Fly ash can have much effect on the strength development of concrete at the condition of mass concrete, hot weather concreting and the concrete products for the steam curing.

• Carbon letters
• /
• v.7 no.1
• /
• pp.27-33
• /
• 2006

Carbon-ceramic composites were fabricated by using fly ash and PANOX fibers as reinforcement. Fly ash, because of its small size particles e.g. submicron to micron level can be effectively dispersed along with fibrous reinforcements. Phenolic resin was used as carbon precursor. Both dry as well as wet methods were used for forming composites. The resulting composites were characterized for their microstructure, thermal and mechanical properties. The microstructure and mechanical properties of composites are found to be dependent on type of the fly ash, fibrous reinforcements as well as processing parameters. The addition of fly ash improves hardness and the fibers, which get co-carbonized on heat treatment, increase the flexural strength of the carbon-ceramic composites. Composites with dual reinforcement exhibit about 30-40% higher strength as compared to the composites made with single reinforcement, either with fly ash as filler or with chopped fibers.

• Resources Recycling
• /
• v.10 no.4
• /
• pp.10-17
• /
• 2001

The present work investigates the possible use of fly ash for the removal of heavy metal ions from aqueous solutions. Batch experiments were conducted and the influences of metal concentration, pH, and fly ash concentration were investigated. Heavy metals used in these studies were lead and zinc. Adsorption studies were done over a range of pH values (3~10) at $25^{\circ}C$ and heavy metal concentrations of 10~400 mg/L using fly ash concentrations of 10 and 20 g/L. Experiments were also conducted without fly ash to determine the extent of heavy metal removal by precipitation. Kinetic and equilibrium experiments were performed and adsorption data were correlated with both Langmuir and Freundlich adsorption models. The results of these studies indicate that 리y ash can be used as an adsorbent for heavy metals in the aqueous solutions, yet the degree of removal depends on the pH.