• Magazine of the Korean Society of Agricultural Engineers
• /
• v.13 no.4
• /
• pp.2456-2470
• /
• 1971

Compaction of soil is very important for construction of soil structures such as highway fills, embankment of reservoir and seadike. With increasing compaction effort, the strength of soil, interor friction and Cohesion increas greatly while the reduction of permerbilityis evident. Factors which may influence compaction effort are moisture content, grain size, grain distribution and other physical properties as well as the variable method of compaction. The moisture content among these parameter is the most important thing. For making the maximum density to a given soil, the comparable optimum water content is required. If there is a slight change in water content when compared with optimum water content, the compaction ratio will decrease and the corresponding mechanical properties will change evidently. The results in this study of soil compaction with different water content are summarized as follows. 1) The maximum dry density increased and corresponding optimum moisture content decreased with increasing of coarse grain size and the compaction curve is steeper than increasing of fine grain size. 2) The maximum dry density is decreased with increasing of the optimum water content and a relationship both parameter becomes rdam-max=2.232-0.02785 $W_0$ But this relstionship will be change to $r_d=ae^{-bw}$ when comparable water content changes. 3) In case of most soils, a dry condition is better than wet condition to give a compactive effort, but the latter condition is only preferable when the liquid limit of soil exceeds 50 percent. 4) The compaction ratio of cohesive soil is greeter than cohesionless soil even the amount of coarse grain sizes are same. 5) The relationship between the maximum dry density and porosity is as rdmax=2,186-0.872e, but it changes to $r_d=ae^{be}$ when water content vary from optimum water content. 6) The void ratio is increased with increasing of optimum water content as n=15.85+1.075 w, but therelation becames $n=ae^{bw}$ if there is a variation in water content. 7) The increament of permeabilty is high when the soil is a high plasticity or coarse. 8) The coefficient of permeability of soil compacted in wet condition is lower than the soil compacted in dry condition. 9) Cohesive soil has higher permeability than cohesionless soil even the amount of coarse particles are same. 10) In generall, the soil which has high optimum water content has lower coefficient of permeability than low optimum water content. 11) The coefficient of permeability has a certain relations with density, gradation and void ratio and it increase with increasing of saturation degree.

• The Korean Nurse
• /
• v.20 no.4 s.112
• /
• pp.39-49
• /
• 1981

기존 간호 영역 내 간호는 질적으로, 양적으로 급격히 팽창 확대되어 가고 있다. 많은 나라에서 건강관리체계가 부적절하게 분배되어 있으며 따라서 많은 사람들이 적절한 건강관리를 제공받지 못하고 있어 수준 높은 양질의 건강관리를 전체적으로 확대시키는 것이 시급하다. 혹 건강관리의 혜택을 받는다고 해도 이들 역시 보다 더 양질의 인간적인 간호를 요하고 있는 실정이다. 간호는 또한 간호영역 자체 내에서도 급격히 확대되어가고 있다. 예를들면, 미국같은 선진국가의 건강간호사(Nurse practitioner)는 간호전문직의 새로운 직종으로 건강관리체계에서 독자적인 실무자로 그 두각을 나타내고 있다. 의사의 심한 부족난으로 고심하는 발전도상에 있는 나라들에서는 간호원들에게 전통적인 간호기능 뿐 아니라 건강관리체계에서 보다 많은 역할을 수행하도록 기대하며 일선지방의 건강센터(Health center) 직종에 많은 간호원을 투입하고 있다. 가령 우리 한국정부에서 최근에 시도한 무의촌지역에서 졸업간호원들이 건강관리를 제공할 수 있도록 한 법적 조치는 이러한 구체적인 예라고 할 수 있다. 기존 간호영역내외의 이런 급격한 변화는 Melvin Toffler가 말한 대로 ''미래의 충격''을 초래하게 되었다. 따라서 이러한 역동적인 변화는 간호전문직에 대하여 몇가지 질문을 던져준다. 첫째, 미래사회에서 간호영역의 특성은 무엇인가? 둘째, 이러한 새로운 영역에서 요구되는 간호원을 길러내기 위해 간호교육자는 어떤 역할을 수행해야 하는가? 셋째 내일의 간호원을 양성하는 간호교육자를 준비시키기 위한 실질적이면서도 현실적인 전략은 무엇인가 등이다. 1. 미래사회에서 간호영역의 특성은 무엇인가? 미래의 간호원은 다음에 열거하는 여러가지 요인으로 인하여 지금까지의 것과는 판이한 환경에서 일하게 될 것이다. 1) 건강관리를 제공하는 과정에서 컴퓨터화되고 자동화된 기계 및 기구 등 새로운 기술을 많이 사용할 것이다. 2) 1차건강관리가 대부분 간호원에 의해 제공될 것이다. 3) 내일의 건강관리는 소비자 주축의 것이 될 것이다. 4) 간호영역내에 많은 새로운 전문분야들이 생길 것이다. 5) 미래의 건강관리체계는 사회적인 변화와 이의 요구에 더 민감한 반응을 하게 될 것이다. 6) 건강관리체계의 강조점이 의료진료에서 건강관리로 바뀔 것이다. 7) 건강관리체계에서의 간호원의 역할은 의료적인 진단과 치료계획의 기능에서 크게 탈피하여 병원내외에서 보다 더 독특한 실무형태로 발전될 것이다. 이러한 변화와 더불어 미래 간호영역에서 보다 효과적인 간호를 수행하기 위해 미래 간호원들은 지금까지의 간호원보다 더 광범위하고 깊은 교육과 훈련을 받아야 한다. 보다 발전된 기술환경에서 전인적인 접근을 하기위해 신체과학이나 의학뿐 아니라 행동과학 $\cdot$ 경영과학 등에 이르기까지 다양한 훈련을 받아야 할 필요가 있다. 또한 행동양상면에서 전문직인 답게 보다 진취적이고 표현적이며 자동적이고 응용과학적인 역할을 수행하도록 훈련을 받아야 한다. 그리하여 간호원은 효과적인 의사결정자$\cdot$문제해결자$\cdot$능숙한 실무자일 뿐 아니라 소비자의 건강요구를 예리하게 관찰하고 이 요구에 효과적인 존재를 발전시켜 나가는 연구자가 되어야 한다. 2. 미래의 간호교육자는 어떤 역할을 수행해야 하는가? 간호교육은 전문직으로서의 실무를 제공하기 위한 기초석이다. 이는 간호교육자야말로 미래사회에서 국민의 건강요구를 충족시키기는 능력있는 간호원을 공급하는 일에 전무해야 함을 시사해준다. 그러면 이러한 일을 달성하기 위해 간호교육자는 무엇을 해야 하는가? 우선 간호교육자는 두가지 측면에서 이 일을 수정해야 된다고 본다. 그 하나는 간호교육기관에서의 측면이고 다른 하나는 간호교육자 개인적인 측면엣서이다. 우선 간호교육기관에서 간호교육자는 1) 미래사회에서 요구되는 간호원을 교육시키기 위한 프로그램을 제공해야 한다. 2) 효과적인 교과과정의 발전과 수정보완을 계속적으로 진행시켜야 한다. 3) 잘된 교과과정에 따라 적절한 훈련을 철저히 시켜야 한다. 4) 간호교육자 자신이 미래의 예측된 현상을 오늘의 교육과정에 포함시킬 수 있는 자신감과 창의력을 가지고 모델이 되어야 한다. 5) 연구 및 학생들의 학습에 영향을 미치는 중요한 의사결정에 학생들을 참여시키도록 해야한다. 간호교육자 개인적인 측면에서는 교육자 자신들이 능력있고 신빙성있으며 간호의 이론$\cdot$실무$\cdot$연구면에 걸친 권위와 자동성$\cdot$독창성, 그리고 인간을 진정으로 이해하려는 자질을 갖추도록 계속 노력해야 한다. 3. 미래의 간호원을 양성하는 능력있는 간호교육자를 준비시키기 위한 실질적이면서도 현실적인 전략은 무엇인가? 내일의 도전을 충족시킬 수 있는 능력있는 간호교육자를 준비시키기 위한 실질적이고 현실적인 전략을 논함에 있어 우리나라의 실정을 참조하겠다. 전문직 간호교육자를 준비하는데 세가지 방법을 통해 할 수 있다고 생각한다. 첫째는 간호원 훈련수준을 전문직 실무를 수행할 수 있는 단계로 면허를 높이는 것이고, 둘째는 훈련수준을 더 향상시키기 위하여 학사 및 석사간호교육과정을 발전시키고 확대하는 것이며, 셋째는 현존하는 간호교육 프로그램의 질을 높이는 것이다. 첫째와 둘째방법은 정부의 관할이 직접 개입되는 방법이기 때문에 여기서는 생략하고 현존하는 교과과정을 발전시키고 그 질을 향상시키는 것에 대해서만 언급하고자 한다. 미래의 여러가지 도전에 부응할 수 있는 교육자를 준비시키는 교육과정의 발전을 두가지 면에서 추진시킬 수 있다고 본다. 첫째는 국제간의 교류를 통하여 idea 및 경험을 나눔으로서 교육과정의 질을 높일 수 있다. 서로 다른 나라의 간호교육자들이 정기적으로 모여 생각과 경험을 교환하고 연구하므로서 보다 체계적이고 효과적인 발전체인(chain)이 형성되는 것이다. ICN같은 국제적인 조직에 의해 이러한 모임을 시도하는 것인 가치있는 기회라고 생각한다. 국가간 또는 국제적인 간호교육자 훈련을 위한 교육과정의 교환은 한 나라안에서 그 idea를 확산시키는데 효과적인 영향을 미칠 수 있다. 충분한 간호교육전문가를 갖춘 간호교육기관이 새로운 교육과정을 개발하여 그렇지 못한 기관과의 연차적인 conference를 가지므로 확산시킬 수도 있으며 이런 방법은 경제적인 면에서도 효과적일 뿐만 아니라 그 나라 그 문화상황에 적합한 교과과정 개발에도 효과적일 수 있다. 간호교육자를 준비시키는 둘째전략은 현존간호교육자들이 간호이론과 실무$\cdot$연구를 통합하고 발전시키는데 있어서 당면하는 여러가지 요인-전인적인 간호에 적절한 과목을 이수하지 못하고 임상실무경험의 부족등-을 보충하는 방법이다. 이런 실제적인 문제를 잠정적으로 해결하기 위하여 1) 몇몇 대학에서 방학중에 계속교육 프로그램을 개발하여 현직 간호교육자들에게 필요하고 적절한 과목을 이수하도록 한다. 따라서 임상실무교육도 이때 실시할 수 있다. 2) 대학원과정 간호교육프로그램의 입학자의 자격에 2$\~$3년의 실무경험을 포함시키도록 한다. 결론적으로 교수와 학생간의 진정한 동반자관계는 자격을 구비한 능력있는 교수의 실천적인 모델을 통하여서 가능하게 이루어 질수 있다고 믿는 바이다.

• The Korean Nurse
• /
• v.20 no.4 s.112
• /
• pp.50-59
• /
• 1981

간호학생들이 당연하고 있는 문제점 미래의 간호학생들이 교육문제를 논하기 위하여는 간호학생들이 가지고 있는 문제점을 파악하고 또 이해하는 것이 우선순위가 될 것이다. 간호학생들이 문제점에 대한 연구는 한국에서 뿐아니라 미국에서도 꽤 많이 시행되어져 왔으며 특히 간호학과정에서 중간 탈락되는 중퇴자들에 대한 연구들 중에 이러한 문제점에 대해서 언급한 것이 많다. 고등학교를 졸업하고 곧 대학과정에 진학한 학생들을 대상으로 조사 보고될 Munro의 자료에 의하면 전문대학과정에서 27$\%$, 대학과정에서는 41$\%$의 간호학생들이 간호학과정에서 중간 탈락하고 있음이 보고되고 있다. 이들이 중간탈락하는 데에는 여러 가지 이유가 있으나 그 중 ''간호학에 흥미를 잃어서''가 가장 큰 이유로 보고되고 있다. 이곳 한국사회에서도 역시 비슷한 현상을 보이고 있다. 그러나 대학입시경쟁과 대학내에서의 전과가 거의 허용되지 않는 특수여건이기 때문에 학교를 중간 탈락하는 율은 미국이 보고만큼 높지는 않으나 역시 ''간호학에 흥미를 잃는다''는 것이 간호학생들의 가장 큰 문제점으로 대두되고 있다. 최근 한국에서 시행된 간호학생들에 관한 연구(표 1 참조)에 의하면 간호학생들의 학문에 대한 만족도는 조사자의 35$\~$50$\%$정도에 불과하였고 더우기 이 비율은 고학년에 올라갈수록 더욱 감소되고 있는 경향을 보이고 있다. 한국에서 시행된 어느 연구보고에 의하면 간호학에 실망했다고 생각하는 학생이 전체의 67$\%$였으며, 다른 학교로 전과를 희망한 경험이 있다는 학생이 71$\%$나 되는 것으로 보고되고 있다. 그러나 왜 흥미를 잃게 되는지 그 이유에 대하여 설명해 주는 연구는 많지 않았다. 미국의 한 저자는 간호학생들이 간호학에 흥미를 잃게 되는 원인을 간호원의 역할에 대한 이해가 정확하지 못한 것과 졸업 후 진로기회에 대한 인식부족 때문이라고 추측하고 있다. 간호학에 흥미를 잃게 되는 이유는 크게 다음의 세 가지로 분류 요약될 수 있다. 첫째, 간호학을 전공으로 택한 동기이다. 간호학의 특수성으로 인하여 학생들이 간호학을 전공으로 택한 동기도 다른 전공분야보다는 훨씬 다른 여러 종류를 보이고 있다. 즉, 종교적 이유, 다른 사람들에게 봉사할 수 있는 직업이기 때문에, 쉽게 취업을 할 수 있어서, 결혼 후에도 직업을 가질 수 있기 때문에, 외국으로 쉽게 취업할 수 있어서 등이 간호학을 선택한 이유로 보고되고 있다. 흥미나 적성에 맞다고 생각하기 때문에 간호학을 택한 학생의 수는 다른 과에 비하여 훨씬 적다. 이러한 흥미나 적성 때문이 아닌 여러 가지 다른 이유들로 인하여 간호학을 택한 경우에 특히 간호학에 쉽게 흥미를 잃어버리는 것을 볼 수 있다. 간호학에 현실적인 개념을 가지고 있는 학생들일수록 추상적이고 현실적인 개념을 가지고 있는 학생들보다 더 간호학에 지속적인 흥미를 가지며 중간에 탈락하는 율이 훨씬 적다는 것이 많은 연구에서 보고되었다. 또한 흥미나 적성 때문에 간호학을 택하였다는 학생들이 다른 과로 전과를 희망하는 율이 낮다는 것도 보고되었다. 둘째, 교과내용자체나 실습에 대한 불만족이다. 간호학에 대한 체계적인 교과내용의 결여, 과중한 과제물, 임상실습에서의 욕구불만, 실습으로 인한 부담, 지식과 실습의 차이점에 대한 갈등 등이 주요 이유로 보고되고 있다. 대부분의 연구들이 이 교과목이나 실습에 대한 불만족, 특히 실습경험에서의 갈등을 학생들이 흥미를 잃는 가장 중요한 요인이 되는 것으로 보고하고 있다. 어느 한 연구에서는 응답자의 90$\%$가 임상실습에 만족하지 못한다고 응답하였으며 그들 중의 88$\%$가 실습감독에 문제가 있다고 생각한다고 보고하였다. 셋째, 교수들에 대한 불만족이다. 대부분의 연구들이 학년이 올라가면 갈수록 교수에 대한 신뢰도가 낮아지며 또한 그에 비례하여 간호학에 대한 만족도가 낮아진다고 보고하고 있다. 교육내용에 대한 전문지식의 결여, 학생들과의 인간적인 관계의 결여, 교수법에 대한 불만족 등이 교수에 대한 불만의 주요내용으로 보고되었다. 미래의 간호에 부응할 학생교육 계속적인 사회적 변동과 더불어 급격하게 변화하고 있는 일반인들의 건강에 대한 요구도와 앞에서 기술한 문제점 등을 감안할 때 학생들에게 동기를 부여하고 간호학에 확신감을 가질 수 있도록 준비시키므로써 간호환경에서 실망하기보다는 오히려 그것을 받아들여 변화하는 사회요구에 책임감을 느낄 수 있도록 교육시키는 것이 미래의 간호학생을 준비시키는데 가장 중요한 요인이라고 할 수 있겠다. 이러한 교육을 위하여 다음의 두가지 안을 제시한다. 1. 교수와 학생간의 관계-서로의 좋은 동반자 : 교수들이 학생에게 미치는 영향, 특히 학생들의 성취도에 대한 영향에 대하여는 이미 많은 연구가 시행되었다. Tetreault(1976)가 간호학생들의 전문의식에 영향을 미치는 요인에 대하여 연구한 바에 의하면 다른 어느 것보다도 교수의 전문의식여부가 학생들의 전문의식 조성에 가장 큰 영향을 미친다고 하였다. 또한 학생들이 교수에게 신뢰감을 가지고 있을때, 교수들이 전문가로서의 행동을 하는 것을 보았을때 비로서 배움이 증가된다고 하였다. Banduras는 엄격하고 무서운 교수보다는 따뜻하고 인간적인 교수에게 학생들이 더 Role Model로서 모방하려는 경향을 나타낸다고 보고 하였다. 그러면 어떻게 학생에게 신뢰받는 교수가 될 수 있겠는가? apos;학생들의 요구에 부응할 때apos;라고 한마디로 표현할 수 있을 것이다. Lussier(1972)가 언급한 것처럼 학생들의 요구에 부응하지 못하는 교육은 Piaget이 언급한 교육의 기본 목표, 즉 개인에게 선배들이 한 것을 그대로 반복하여 시행하도록 하는 것이 아니라 새로운 것을 시도할 수 있는 능력을 가지게 하는 목표에는 도달할 수 없으며 이러한 목표는 간호학에도 가장 기본이 되어야 할 기본목표이기 때문이다. 학생들이 현재 어떤 요구를 가지고 있으며 또 어떤 생각을 하고 있는지 계속 파악하고 있는 것이 학생요구에 부응하는 교육을 할 수 있는 기본조건이 될 것이다. 의외로 많은 교수들이 학생들을 이해하고 있다고 생각하고 있으나 잘못 이해하고 있는 경우가 많다. 표 2는 현 간호학생들이 생각하고 있는 가치관과 문제점을 파악하고 또 교수가 그 가치관과 문제점을 어느 정도 파악하고 있는지 알아보기 위하여 일개 4년제 대학 200여명의 학생과 그 대학에 근무하는 18명의 교수진을 대상으로 질문한 결과를 간략하게 보고한 것이다. 또한 여기에서 학생이 보고하는 가치관, 문제점, 교수에게 바라는 점이 교수가 이해하고 있는 것과 차이가 있다는 것도 보여주고 있다. 우리가 학생들의 요구를 파악할 수 있도록 귀를 기울이고 이해하며, 그 요구에 부응하려고 노력할때 진정한 교수와 학생간의 관계가 이루어질 수 있을 것이며 이때 비로서 우리는 apos;partnershipapos;을 이룰 수 있을 것이다. 이때 간호학에 대한 실망은 줄어들 수 있을 것이며 우리도 학생들에게 전문가적인 태도를 함양시켜줄 수 있는 기회를 부여할 수 있을 것이다. 이렇게 될때 앞으로 기다리고 있는 미지의 의무에 효과적으로 또 적극적으로 대처할 수 있는 자질을 형성한 학생들을 준비해 낼 수 있을 것이다. 2. 간호모델에 의한 교과과정의 확립과 임상실습에의 적용 : 교과과정이 학생들의 모양을 만들어주는 하나의 기본틀이라고 말할 수 있다면 미래의 요구에 부응하는 학생들을 준비시키기 위하여 지금까지와는 다른 새로운 방향의 교과과정이 필요하다는 것은 재론할 필요가 없을 것이다. 이미 진취적인 간호대학에서는 guided design systems approach 또는 integrated curriculum 등의 새로운 교과과정을 시도하고 있음은 알려진 사실이다. 물론 간호모델에 준한 교과과정을 발전시키는데 대한 장점과 이에 수반되는 여러가지 새로운 문제점에 대하여 많은 논란이 있으나 모든 교과과정이 처음 시도될 때부터 완전한 것이 있을 수 없으며 시간이 지남에 따라 성숙되는 것임을 감안해 볼 때 이러한 새로운 교과과정에의 시도는 미래의 새로운 간호방향에 필수적인 사업이라고 하겠다. 이러한 교과과정을 개발하는데 몇가지 게안점을 첨부하려 한다. (1) 새로운 교과과정의 개발은 처음부터 끝까지 모든 교수진의 협력과 참여로 이루어져야 한다. (2) 비록 처음에는 어렵고 혼란이 있더라도 교과과정은 의학모델이 아닌 간호모델을 중심으로 이루어져야 한다. (3) 간호모델에서 다루어지는 개념들은 모두 직접 간호업무에 적용될 수 있는 것으로 선택되어야 한다. (4) 교과과정의 결과로 배출되는 학생들의 준비정도는 그 지역사회에 적합하여야 한다. (5) 그 지역사회의 고유한 문화적 요소가 포함되어야 한다. 아직 우리는 간호분야 내부의 갈등을 해결하지 못하고 있는 시기에 있다. 우리 내부의 문제점을 잘 해결할 수 있을때 외부와의 갈등에 잘 대처할 수 있을 것이다. 내부의 갈등을 잘 해결하기 위한 힘을 모으기 위하여는 동반자, 즉 교수와 학생, 간호교육자와 임상간호원 등이 서로 진정한 의미의 동반자 될때 가장 중요한 해결의 실마리가 될 것이다.

• Korean small business review
• /
• v.32 no.1
• /
• pp.65-87
• /
• 2010

With the advent of knowledge-based society, the revitalization of technological innovation type SMEs, termed "inno-biz" hereafter, has been globally recognized as a government policymakers' primary concern in strengthening national competitiveness, and much effort is being put into establishing polices of boosting the start-ups and innovation capability of SMEs. Especially, in that the inno-biz enables national economy to get vitalized by widening world markets with its superior technology, and thus, taking the initiative of extremely competitive world markets, its growth and development has greater significance. In the case of Korea, the government has been maintaining the policies since the late 1990s of stimulating the growth of SMEs as well as building various infrastructures to foster the start-ups of the SMEs such as venture businesses with high technology. In addition, since the enactment of "Innovation Promotion Law for SMEs" in 2001, the government has been accelerating the policies of prioritizing the growth and development of inno-biz. So, for the sound growth and development of Korean inno-biz, this paper intends to offer effective management strategies for SMEs and suggest proper policies for the government, by researching into the effect of technological innovation capability and technology commercialization capability as the primary business resources on business performance in Korean SMEs in the light of market information orientation. The research is carried out on Korean companies characterized as inno-biz. On the basis of OSLO manual and prior studies, the research categorizes their status. R&D capability, technology accumulation capability and technological innovation system are categorized into technological innovation capability; product development capability, manufacturing capability and marketing capability into technology commercialization capability; and increase in product competitiveness and merits for new technology and/or product development into business performance. Then the effect of each component on business performance is substantially analyzed. In addition, the mediation effect of technological innovation and technology commercialization capability on business performance is observed by the use of the market information orientation as a parameter. The following hypotheses are proposed. H1 : Technology innovation capability will positively influence business performance. H1-1 : R&D capability will positively influence product competitiveness. H1-2 : R&D capability will positively influence merits for new technology and/or product development into business performance. H1-3 : Technology accumulation capability will positively influence product competitiveness. H1-4 : Technology accumulation capability will positively influence merits for new technology and/or product development into business performance. H1-5 : Technological innovation system will positively influence product competitiveness. H1-6 : Technological innovation system will positively influence merits for new technology and/or product development into business performance. H2 : Technology commercializing capability will positively influence business performance. H2-1 : Product development capability will positively influence product competitiveness. H2-2 : Product development capability will positively influence merits for new technology and/or product development into business performance. H2-3 : Manufacturing capability will positively influence product competitiveness. H2-4 : Manufacturing capability will positively influence merits for new technology and/or product development into business performance. H2-5 : Marketing capability will positively influence product competitiveness. H2-6 : Marketing capability will positively influence merits for new technology and/or product development into business performance. H3 : Technology innovation capability will positively influence market information orientation. H3-1 : R&D capability will positively influence information generation. H3-2 : R&D capability will positively influence information diffusion. H3-3 : R&D capability will positively influence information response. H3-4 : Technology accumulation capability will positively influence information generation. H3-5 : Technology accumulation capability will positively influence information diffusion. H3-6 : Technology accumulation capability will positively influence information response. H3-7 : Technological innovation system will positively influence information generation. H3-8 : Technological innovation system will positively influence information diffusion. H3-9 : Technological innovation system will positively influence information response. H4 : Technology commercialization capability will positively influence market information orientation. H4-1 : Product development capability will positively influence information generation. H4-2 : Product development capability will positively influence information diffusion. H4-3 : Product development capability will positively influence information response. H4-4 : Manufacturing capability will positively influence information generation. H4-5 : Manufacturing capability will positively influence information diffusion. H4-6 : Manufacturing capability will positively influence information response. H4-7 : Marketing capability will positively influence information generation. H4-8 : Marketing capability will positively influence information diffusion. H4-9 : Marketing capability will positively influence information response. H5 : Market information orientation will positively influence business performance. H5-1 : Information generation will positively influence product competitiveness. H5-2 : Information generation will positively influence merits for new technology and/or product development into business performance. H5-3 : Information diffusion will positively influence product competitiveness. H5-4 : Information diffusion will positively influence merits for new technology and/or product development into business performance. H5-5 : Information response will positively influence product competitiveness. H5-6 : Information response will positively influence merits for new technology and/or product development into business performance. H6 : Market information orientation will mediate the relationship between technology innovation capability and business performance. H7 : Market information orientation will mediate the relationship between technology commercializing capability and business performance. The followings are the research results : First, as for the effect of technological innovation on business performance, the technology accumulation capability and technological innovating system have a positive effect on increase in product competitiveness and merits for new technology and/or product development, while R&D capability has little effect on business performance. Second, as for the effect of technology commercialization capability on business performance, the effect of manufacturing capability is relatively greater than that of merits for new technology and/or product development. Third, the mediation effect of market information orientation is identified to exist partially in information generation, information diffusion and information response. Judging from these results, the following analysis can be made : On Increase in product competitiveness, directly related to successful technology commercialization of technology, management capability including technological innovation system, manufacturing capability and marketing capability has a relatively strong effect. On merits for new technology and/or product development, on the other hand, capability in technological aspect including R&D capability, technology accumulation capability and product development capability has relatively strong effect. Besides, in the cast of market information orientation, the level of information diffusion within an organization plays and important role in new technology and/or product development. Also, for commercial success like increase in product competitiveness, the level of information response is primarily required. Accordingly, the following policies are suggested : First, as the effect of technological innovation capability and technology commercialization capability on business performance differs among SMEs; in order for SMEs to secure competitiveness, the government has to establish microscopic policies for SMEs which meet their needs and characteristics. Especially, the SMEs lacking in capital and labor are required to map out management strategies of focusing their resources primarily on their strengths. And the government needs to set up policies for SMEs, not from its macro-scaled standpoint, but from the selective and concentrative one that meets the needs and characteristics of respective SMEs. Second, systematic infrastructures are urgently required which lead technological success to commercial success. Namely, as technological merits at respective SME levels do not always guarantee commercial success, the government should make and effort to build systematic infrastructures including encouragement of M&A or technology trade, systematic support for protecting intellectual property, furtherance of business incubating and industrial clusters for strengthening academic-industrial network, and revitalization of technology financing, in order to make successful commercialization from technological success. Finally, the effort to innovate technology, R&D, for example, is essential to future national competitiveness, but its result is often prolonged. So the government needs continuous concern and funding for basic science, in order to maximize technological innovation capability. Indeed the government needs to examine continuously whether technological innovation capability or technological success leads satisfactorily to commercial success in market economic system. It is because, when the transition fails, it should be left to the government.

• Asia pacific journal of information systems
• /
• v.21 no.1
• /
• pp.103-122
• /
• 2011

Recently, numerous documents have been made available electronically. Internet search engines and digital libraries commonly return query results containing hundreds or even thousands of documents. In this situation, it is virtually impossible for users to examine complete documents to determine whether they might be useful for them. For this reason, some on-line documents are accompanied by a list of keywords specified by the authors in an effort to guide the users by facilitating the filtering process. In this way, a set of keywords is often considered a condensed version of the whole document and therefore plays an important role for document retrieval, Web page retrieval, document clustering, summarization, text mining, and so on. Since many academic journals ask the authors to provide a list of five or six keywords on the first page of an article, keywords are most familiar in the context of journal articles. However, many other types of documents could not benefit from the use of keywords, including Web pages, email messages, news reports, magazine articles, and business papers. Although the potential benefit is large, the implementation itself is the obstacle; manually assigning keywords to all documents is a daunting task, or even impractical in that it is extremely tedious and time-consuming requiring a certain level of domain knowledge. Therefore, it is highly desirable to automate the keyword generation process. There are mainly two approaches to achieving this aim: keyword assignment approach and keyword extraction approach. Both approaches use machine learning methods and require, for training purposes, a set of documents with keywords already attached. In the former approach, there is a given set of vocabulary, and the aim is to match them to the texts. In other words, the keywords assignment approach seeks to select the words from a controlled vocabulary that best describes a document. Although this approach is domain dependent and is not easy to transfer and expand, it can generate implicit keywords that do not appear in a document. On the other hand, in the latter approach, the aim is to extract keywords with respect to their relevance in the text without prior vocabulary. In this approach, automatic keyword generation is treated as a classification task, and keywords are commonly extracted based on supervised learning techniques. Thus, keyword extraction algorithms classify candidate keywords in a document into positive or negative examples. Several systems such as Extractor and Kea were developed using keyword extraction approach. Most indicative words in a document are selected as keywords for that document and as a result, keywords extraction is limited to terms that appear in the document. Therefore, keywords extraction cannot generate implicit keywords that are not included in a document. According to the experiment results of Turney, about 64% to 90% of keywords assigned by the authors can be found in the full text of an article. Inversely, it also means that 10% to 36% of the keywords assigned by the authors do not appear in the article, which cannot be generated through keyword extraction algorithms. Our preliminary experiment result also shows that 37% of keywords assigned by the authors are not included in the full text. This is the reason why we have decided to adopt the keyword assignment approach. In this paper, we propose a new approach for automatic keyword assignment namely IVSM(Inverse Vector Space Model). The model is based on a vector space model. which is a conventional information retrieval model that represents documents and queries by vectors in a multidimensional space. IVSM generates an appropriate keyword set for a specific document by measuring the distance between the document and the keyword sets. The keyword assignment process of IVSM is as follows: (1) calculating the vector length of each keyword set based on each keyword weight; (2) preprocessing and parsing a target document that does not have keywords; (3) calculating the vector length of the target document based on the term frequency; (4) measuring the cosine similarity between each keyword set and the target document; and (5) generating keywords that have high similarity scores. Two keyword generation systems were implemented applying IVSM: IVSM system for Web-based community service and stand-alone IVSM system. Firstly, the IVSM system is implemented in a community service for sharing knowledge and opinions on current trends such as fashion, movies, social problems, and health information. The stand-alone IVSM system is dedicated to generating keywords for academic papers, and, indeed, it has been tested through a number of academic papers including those published by the Korean Association of Shipping and Logistics, the Korea Research Academy of Distribution Information, the Korea Logistics Society, the Korea Logistics Research Association, and the Korea Port Economic Association. We measured the performance of IVSM by the number of matches between the IVSM-generated keywords and the author-assigned keywords. According to our experiment, the precisions of IVSM applied to Web-based community service and academic journals were 0.75 and 0.71, respectively. The performance of both systems is much better than that of baseline systems that generate keywords based on simple probability. Also, IVSM shows comparable performance to Extractor that is a representative system of keyword extraction approach developed by Turney. As electronic documents increase, we expect that IVSM proposed in this paper can be applied to many electronic documents in Web-based community and digital library.

• Korean Journal of Hospice Care
• /
• v.7 no.1
• /
• pp.5-14
• /
• 2007

Objective : This study was done to identify the status of Spiritual Well-Being in Nursing Students and to investigate the correlation between related various characteristics and Spiritual Well-Being and to provide baseline data for ride school-life and development of Spiritual-education program for nursing students. Method : The data was collected from 188 christian Nursing students by using questionary method. they are all all agreed to participate in this study. Their Spiritual Well-Being were measured using Spiritual Well-Being scale developed by Paloutzian & Ellison(1983) and translated by Choi(1990) and reversed by Kang(1996). Results : The data was analyzed by using SPSS/PC+12.0. The summary of results were as follows; 1. The mean score of Spiritual Well-Being were $63.95\pm10.256$(range from 20-80) 2. There were significant differences between the grade(F=6.101, p= .001), type of religion(F= 17.703, p= .000), In Christian, the level of devotee(F=8.194, p= .000), duration of church attendance(F=7.947, p= .000), regular attendance of chapel(F=4.242, p= .000), regular reading(study) of Bible and prayer (F=5.863, p= .001=0). perceived personal encounter with Jesus(F=4.160, p= .000), religion of parent(F=9.320, p= .000), perceived attitude of parenting(F=4.146, p= .000), hope to admit/transfer to other course or not(F=-2.050, p= .050). Conclusion : Our results were valuable to provide basic guidelines for ride school-life and for the development of Spiritual-education program for Nursing students.

• Korean Journal of Health Education and Promotion
• /
• v.2 no.1
• /
• pp.3-50
• /
• 1984

The levels of health knowledge, attitude and practice of housewives considerably effect to the health of households, communities and the nation. This study was designed to grasp the levels of health knowledge, attitude and practice of houswives and analyse the various factors effecting to health in order to provide health education services as well as materials for effective formulation and implementation of health policy to improve the health of the nation. This study has been conducted through interviews by trained surveyers for 4,281 housewives selected from 4,500 households throughout the country for 40 days during July 11-August 20, 1983. The results of survey were analysed by stepwise multiple regression and path analysis are summarized as follows; 1. Based on the measurement instrument applied to this study, the levels of health knowledge, attitude and practice of housewives were extremely low with 54.5 points out of 100 points in full. Higher level with 72 points and above was approximately 21 percent and lower level with 39 points and below was approx. 24 percent. The middle level was approx. 55 percent. In order to implement health programs successively, health education should be more strengthened and to improve the level of health knowledge, attitude and practice (KAP) of the nation, political consideration as a part of spiritual reformation must be concentrated on health. 2. The level of health knowledge indicated the highest points with 57.3 the level of attitude was the second with 55.0 points and the practice level was the lowest with 50.0 point. Therefore, planning and implementation of health education program must be based on the persuasion and motivation that health knowledge turn into practice. 3. Housewives who had higher level of health knowledge, showed their practice level was relatively lower and those who had middle or low level of it practice level was the reverse. 4. Correlations among health knowledge, attitude and practice (KAP) were generally higher and statistically significant at 0.1 percent level. Correlation between total health KAP level and health knowledge was the highest with r=.8092. 5. Health KAP levels showed significant differences according to the age, number of children, marital status, self-assessed health status and concern on health of the housewives interviewed (p<0.001) 6. Health KAP levels also showed significant differences according to the education level, economic status, employment before marriage and grown-up area of the housewives interviewed. (p<0.001) 7. Heath KAP levels showed significant differences according to health insurance benificiary and the existence of patients in the family. (p<0.001). 8. Health KAP levels showed significant differences according to distance to government organizations, schools, distance to health facilities, telephone possession rate, television possession rate, newspaper reading rate and activities of Ban meeting and Women's club. (p<0.001) 9. Health KAP levels showed significant differences according to electric mass communication media such as television, radio and village broadcasting etc. and printed media such as newspaper, magazine and booklets etc., IEC variables such as individual consultation and husband-wife communication, however, there was no significance with group training. 10. Health KAP of the housewives showed close correlation with personal characteristics variables, i.e., education level (r=.5302), age (r=-.3694) grown-up area (r=.3357) and employment before marriage. In general, correlation of health knowledge level was higher than the levels of attitude or practice. In case of health concern and health insurance, correlation of practice level was higher than health knowledge level. 11. Health KAP levels showed higher correlation with community environmental characteristics, Ban meeting and activity of Women's club, however, no correlation with New-village movement. 12. Among IEC variables, husband-wife communication showed the highest correlation with health KAP levels and printed media, electric mas communication media and health consultation in order. Therefore, encouragement of husband-wife communication and development of training program for men should be included in health education program. 13. Mass media such as electric mass com. and printed media were effective for knowledge transmission and husband-wife communication and individual consultation were effective for health practice. Group training was significant for knowledge transmission, however, but not significant for attitude formation or turning to health practice. To improve health KAP levels, health knowledge should be transmitted via mass media and health consultation with health professionals and field health workers should be strengthened. 14. Correlation of health KAP levels showed that knowledge level was generally higher than that of practice and recognized that knowledge was not linked with attitude or practice. 15. The twenty-five variables effecting health KAP levels of housewives had 41 per cent explanation variances among which education level had great contribution (β=.2309) and electric mass com. media (β=.1778), husband-wife communication (β=.1482), printed media, grown-up area, and distance to government organizations in order. Variances explained (R²) of health KAP were 31%, 15%, and 30% respectively. 16. Principal variables contributed to health KAP were education level (β=.12320, β=.1465), electric mass comm. media (β=.1762, β=.1839), printed media, (β=.1383, β=.1420) husband-wife communication (β=.1004, β=.1067), grown-up area and distance to government organizations, in order. Since education level contributes greatly to health KAP of the housewives, health education including curriculum development in primary, middle and high schools must be emphasized and health science must be selected as one of the basic liberal arts subject in universities. 17. Variences explained of IEC variables to health KAP were 19% in total, 14% in knowledge, 9% in attitude, and 10% in health practice. Contributions of IEC variables to health KAP levels were printed media (β=.3882), electric mass comm media (β=.3165), husb-band wife com. (β=.2095,) and consultation on health (β=.0841) in order, however, group training showed negative effect (β=-.0402). National fund must be invested for the development of Health Program through mass media such as TV and radio etc. and for printed materials such as newspaper, magazines, phamplet etc. needed for transmission of health knowledge. 18. Variables contributed to health KAP levels through IEC variables with indirect effects were education level (Ind E=0.0410), health concern (Ind E=.0161), newspaper reading rate (Ind E=.0137), TV possession rate and activity of Ban meeting in order, however, health facility showed negative effect (Ind E=-.0232) and other variables showed direct effect but not indirect effect. 19. Among the variables effecting health KAP level, education level showed the highest in total effect (TE=.2693) then IEC (TE=.1972), grown-up city (TE=.1237), newspaper reading rate (TE=.1020), distance to government organization (TE=.095) in order. 20. Variables indicating indirect effects to health KAP levels were; at knowledge level with R²=30%, education level (Ind E=.0344), newspaper reading rate (Ind E=.0112), TV possession rate (Ind E=.0689), activity of Ban meeting (Ind E=.0079) in order and at attitude level with R²=13%, education level (Ind E=. 0338), activity of Ban meeting (Ind E=.0079), and at practice level with R²=29%. education level (Ind E=.0268), health facility (Ind E=.0830) and concern on health (Ind E=.0105). 21. Total effect to health KAP levels and IEC by variable characteristics, personal characteristics variables indicated larger than community characteristics variables. 22. Multiple Correlation Coefficient (MCC) expressed by the Personal Characteristic Variable was .5049 and explained approximately 25% of variances. MCC expressed by total Community environment variable was .4283 and explained approx. 18% of variances. MCC expressed by IEC Variables was .4380 and explained approx. 19% of variances. The most important variable effected to health KAP levels was personal characteristic and then IEC variable, Community Environment variable in order. When the IEC effected with personal characteristic or community characteristic, the MCC or the variances were relatively higher than effecting alone. Therefore it was identified that the IEC was one of the important intermediate variable.

• The Korean Nurse
• /
• v.36 no.1
• /
• pp.77-96
• /
• 1997

The duty shifts of hospital nurses not only affect nurses' physical and mental health but also present various personnel management problems which often result in high turnover rates. In this context a study was carried out from October to November 1995 for a period of two months to find out the status of hospital nurses' duty shift patterns, and preferred duty hours and fixed duty shifts. The study population was 867 RNs working in five general hospitals located in Seoul and its vicinity. The questionnaire developed by the writer was used for data collection. The response rate was 85.9 percent or 745 returns. The SAS program was used for data analysis with the computation of frequencies, percentages and Chi square test. The findings of the study are as follows: 1. General characteristics of the study population: 56 percent of respondents was (25 years group and 76.5 percent were "single": the predominant proportion of respondents was junior nursing college graduates(92.2%) and have less than 5 years nursing experience in hospitals(65.5%). For their future working plan in nursing profession, nearly 50% responded as uncertain The reasons given for their career plan was predominantly 'personal growth and development' rather than financial reasons. 2. The interval for rotations of duty stations was found to be mostly irregular(56.4%) while others reported as weekly(16.1%), monthly(12.9%), and fixed terms(4.6%). 3. The main problems related to duty shifts particularly the evening and night duty nurses reported were "not enough time for the family, " "afraid of security problems after the work when returning home late at night." and "lack of leisure time". "problems in physical and physiological adjustment." "problems in family life." "lack of time for interactions with fellow nurses" etc. 4. The forty percent of respondents reported to have '1-2 times' of duty shift rotations while all others reported that '0 time'. '2-3 times'. 'more than 3 times' etc. which suggest the irregularity in duty shift rotations. 5. The majority(62.8%) of study population found to favor the rotating system of duty stations. The reasons for favoring the rotation system were: the opportunity for "learning new things and personal development." "better human relations are possible. "better understanding in various duty stations." "changes in monotonous routine job" etc. The proportion of those disfavor the rotating 'system was 34.7 percent. giving the reasons of"it impedes development of specialization." "poor job performances." "stress factors" etc. Furthermore. respondents made the following comments in relation to the rotation of duty stations: the nurses should be given the opportunity to participate in the. decision making process: personal interest and aptitudes should be considered: regular intervals for the rotations or it should be planned in advance. etc. 6. For the future career plan. the older. married group with longer nursing experiences appeared to think the nursing as their lifetime career more likely than the younger. single group with shorter nursing experiences ($x^2=61.19.{\;}p=.000;{\;}x^2=41.55.{\;}p=.000$). The reason given for their future career plan regardless of length of future service, was predominantly "personal growth and development" rather than financial reasons. For further analysis, the group those with the shorter career plan appeared to claim "financial reasons" for their future career more readily than the group who consider the nursing job as their lifetime career$(x^2$= 11.73, p=.003) did. This finding suggests the need for careful .considerations in personnel management of nursing administration particularly when dealing with the nurses' career development. The majority of respondents preferred the fixed day shift. However, further analysis of those preferred evening shift by age and civil status, "< 25 years group"(15.1%) and "single group"(13.2) were more likely to favor the fixed evening shift than > 25 years(6.4%) and married(4.8%)groups. This differences were statistically significant ($x^2=14.54, {\;}p=.000;{\;}x^2=8.75, {\;}p=.003$). 7. A great majority of respondents(86.9% or n=647) found to prefer the day shifts. When the four different types of duty shifts(Types A. B. C, D) were presented, 55.0 percent of total respondents preferred the A type or the existing one followed by D type(22.7%). B type(12.4%) and C type(8.2%). 8. When the condition of monetary incentives for the evening(20% of salary) and night shifts(40% of. salary) of the existing duty type was presented. again the day shift appeared to be the most preferred one although the rate was slightly lower(66.4% against 86.9%). In the case of evening shift, with the same incentive, the preference rates for evening and night shifts increased from 11.0 to 22.4 percent and from 0.5 to 3.0 percent respectively. When the age variable was controlled. < 25 yrs group showed higher rates(31.6%. 4.8%) than those of > 25 yrs group(15.5%. 1.3%) respectively preferring the evening and night shifts(p=.000). The civil status also seemed to operate on the preferences of the duty shifts as the single group showed lower rate(69.0%) for day duty against 83. 6% of the married group. and higher rates for evening and night duties(27.2%. 15.1%) respectively against those of the married group(3.8%. 1.8%) while a higher proportion of the married group(83. 6%) preferred the day duties than the single group(69.0%). These differences were found to be statistically all significant(p=.001). 9. The findings on preferences of three different types of fixed duty hours namely, B, C. and D(with additional monetary incentives) are as follows in order of preference: B type(12hrs a day, 3days a wk): day shift(64.1%), evening shift(26.1%). night shift(6.5%) C type(12hrs a day. 4days a wk) : evening shift(49.2%). day shift(32.8%), night shift(11.5%) D type(10hrs a day. 4days a wk): showed the similar trend as B type. The findings of higher preferences on the evening and night duties when the incentives are given. as shown above, suggest the need for the introductions of different patterns of duty hours and incentive measures in order to overcome the difficulties in rostering the nursing duties. However, the interpretation of the above data, particularly the C type, needs cautions as the total number of respondents is very small(n=61). It requires further in-depth study. In conclusion. it seemed to suggest that the patterns of nurses duty hours and shifts in the most hospitals in the country have neither been tried for different duty types nor been flexible. The stereotype rostering system of three shifts and insensitiveness for personal life aspect of nurses seemed to be prevailing. This study seems to support that irregular and frequent rotations of duty shifts may be contributing factors for most nurses' maladjustment problems in physical and mental health. personal and family life which eventually may result in high turnover rates. In order to overcome the increasing problems in personnel management of hospital nurses particularly in rostering of evening and night duty shifts, which may related to eventual high turnover rates, the findings of this study strongly suggest the need for an introduction of new rostering systems including fixed duties and appropriate incentive measures for evenings and nights which the most nurses want to avoid, In considering the nursing care of inpatients is the round-the clock business. the practice of the nursing duty shift system is inevitable. In this context, based on the findings of this study. the following are recommended: 1. The further in-depth studies on duty shifts and hours need to be undertaken for the development of appropriate and effective rostering systems for hospital nurses. 2. An introduction of appropriate incentive measures for evening and night duty shifts along with organizational considerations such as the trials for preferred duty time bands, duty hours, and fixed duty shifts should be considered if good quality of care for the patients be maintained for the round the clock. This may require an initiation of systematic research and development activities in the field of hospital nursing administration as a part of permanent system in the hospital. 3. Planned and regular intervals, orientation and training, and professional and personal growth should be considered for the rotation of different duty stations or units. 4. In considering the higher degree of preferences in the duty type of "10hours a day, 4days a week" shown in this study, it would be worthwhile to undertake the R&D type studies in large hospital settings.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.11 no.1
• /
• pp.1534-1548
• /
• 1969

This experiment was conducted, making use of the 'NONG-RIM6' arecommended variety of rice for the year of 1968. Main purposes of the experiment are to explore possibilities of; a) ways and means of saving irringation water and, b) overcoming drought at the same time so that an increased yield in rice could be resulted in. Specifically, it was tried to determine the effects of the Rotation irrigation method combined with differentiated thickness of lining upon the growth and yield of rice. Some of the major findings are summarized in the following. 1) The different thicknesses show a significant relationship with the weight of 1,000 grains. In the case of 9cm lined plot, the grain weight is 23.5grams, the heaviest. Next in order is 3cm lined plot, 6cm lined plot, control plot, and wheat straw lined-plot. 2) In rice yield, it is found that there is a considerably moderate significant relationship with both the different thickness of lining and the number of irrigation, as shown in the table. 3) There is little or no difference among different plots in terms of a) physical and chemical properties of soil, b) quality of irrigation water, c) climatic conditions, and rainfalls. 4) It is found that there is a significant relationship between differences in the method of rotation irrigation and the number of ears per hill. The plot irrigated at an interval of 7 days shows 17.4 ears and plot irrigated at an interval of 6 days, 16.3 5) In vinyl-treated plots, it is shown that both yield and component elements are greatest in the case of the plot ith whole of $3cm/m^2$ Next in order are the plot with a hole of $2cm/m^2$ the plot with a hole of $1cm/m^2$ In the case of the plot with no hole it is found that both yield and component elements are decreased as compared to the control plot. 6) The irrigation water reqirement is measured for the actual irrigation days of 72 which are the number subtracted the days of rainfall of 30 from the total irrigation days of 102. It is found that the irrigation water requirement for the uncontrol plot is 1,590mm as compared to 876mm(44.9% saved) for the 9cm-lined plot, 959mm(39.7% saved) for the 6cm-lined plot 1,010mm(36% saved) for the 3cm-lined plot and 1,082mm(32% saved) for the wheat straw lined plot. In the case of the Rotation irrigation method it is found that the water requirement for the plot irrigated at an interval of 8 days is 538mm(65% saved), as compared to 617mm(61.6% saved) for plot irrigated at an interval of 7 day 672mm(57.7% saved) for plot irrigated at an interval of 6day, 746mm(53.0% saved) for the plot irrigated at an interval of 5 days, 890mm 44.0% saved) for the plot irrigated at an interval of 4 days, and 975mm(38.6% saved) for the plot irrigated at an interval of 3 days. 7) The rate of evapotranspiration is found 2.8 around the end of month of July, as compared to 2.6 at the begining of August 3.4 around the end of August and 2.6 at the begining of August 3.4 around the end of August and 2.6 at the begining of September. 8) It is found that the saturation quantity of 30mm per day is decreased to 20mm per day though the use of vinyl covering. 9) The husking rate shows 75 per cent which is considered better.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3225-3262
• /
• 1974

The purposes of this thesis are to clarify experimentally the variation of ground water temperature in tube wells during the irrigation period of paddy rice, and the effect of ground water irrigation on the growth, grain yield and yield components of the rice plant, and, furthermore, when and why the plant is most liable to be damaged by ground water, and also to find out the effective ground water irrigation methods. The results obtained in this experiment are as follows; 1. The temperature of ground water in tube wells varies according to the location, year, and the depth of the well. The average temperatures of ground water in a tubewells, 6.3m, 8.0m deep are $14.5^{\circ}C$ and $13.1^{\circ}C$, respercively, during the irrigation period of paddy rice (From the middle of June to the end of September). In the former the temperature rises continuously from $12.3^{\circ}C$ to 16.4$^{\circ}C$ and in the latter from $12.4^{\circ}C$ to $13.8^{\circ}C$ during the same period. These temperatures are approximately the same value as the estimated temperatures. The temperature difference between the ground water and the surface water is approximately $11^{\circ}C$. 2. The results obtained from the analysis of the water quality of the "Seoho" reservoir and that of water from the tube well show that the pH values of the ground water and the surface water are 6.35 and 6.00, respectively, and inorganic components such as N, PO4, Na, Cl, SiO2 and Ca are contained more in the ground water than in the surface water while K, SO4, Fe and Mg are contained less in the ground water. 3. The response of growth, yield and yield components of paddy rice to ground water irrigation are as follows; (l) Using ground water irrigation during the watered rice nursery period(seeding date: 30 April, 1970), the chracteristics of a young rice plant, such as plant height, number of leaves, and number of tillers are inferior to those of young rice plants irrigated with surface water during the same period. (2) In cases where ground water and surface water are supplied separately by the gravity flow method, it is found that ground water irrigation to the rice plant delays the stage at which there is a maximum increase in the number of tillers by 6 days. (3) At the tillering stage of rice plant just after transplanting, the effect of ground water irrigation on the increase in the number of tillers is better, compared with the method of supplying surface water throughout the whole irrigation period. Conversely, the number of tillers is decreased by ground water irrigation at the reproductive stage. Plant height is extremely restrained by ground water irrigation. (4) Heading date is clearly delayed by the ground water irrigation when it is practised during the growth stages or at the reproductive stage only. (5) The heading date of rice plants is slightly delayed by irrigation with the gravity flow method as compared with the standing water method. (6) The response of yield and of yield components of rice to ground water irrigation are as follows: \circled1 When ground water irrigation is practised during the growth stages and the reproductive stage, the culm length of the rice plant is reduced by 11 percent and 8 percent, respectively, when compared with the surface water irrigation used throughout all the growth stages. \circled2 Panicle length is found to be the longest on the test plot in which ground water irrigation is practised at the tillering stage. A similar tendency as that seen in the culm length is observed on other test plots. \circled3 The number of panicles is found to be the least on the plot in which ground water irrigation is practised by the gravity flow method throughout all the growth stages of the rice plant. No significant difference is found between the other plots. \circled4 The number of spikelets per panicle at the various stages of rice growth at which_ surface or ground water is supplied by gravity flow method are as follows; surface water at all growth stages‥‥‥‥‥ 98.5. Ground water at all growth stages‥‥‥‥‥‥62.2 Ground water at the tillering stage‥‥‥‥‥ 82.6. Ground water at the reproductive stage ‥‥‥‥‥ 74.1. \circled5 Ripening percentage is about 70 percent on the test plot in which ground water irrigation is practised during all the growth stages and at the tillering stage only. However, when ground water irrigation is practised, at the reproductive stage, the ripening percentage is reduced to 50 percent. This means that 20 percent reduction in the ripening percentage by using ground water irrigation at the reproductive stage. \circled6 The weight of 1,000 kernels is found to show a similar tendency as in the case of ripening percentage i. e. the ground water irrigation during all the growth stages and at the reproductive stage results in a decreased weight of the 1,000 kernels. \circled7 The yield of brown rice from the various treatments are as follows; Gravity flow; Surface water at all growth stages‥‥‥‥‥‥514kg/10a. Ground water at all growth stages‥‥‥‥‥‥428kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥430kg/10a. Standing water; Surface water at all growh stages‥‥‥‥‥‥556kg/10a. Ground water at all growth stages‥‥‥‥‥‥441kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥450kg/10a. The above figures show that ground water irrigation by the gravity flow and by the standing water method during all the growth stages resulted in an 18 percent and a 21 percent decrease in the yield of brown rice, respectively, when compared with surface water irrigation. Also ground water irrigation by gravity flow and by standing water resulted in respective decreases in yield of 16 percent and 19 percent, compared with the surface irrigation method. 4. Results obtained from the experiments on the improvement of ground water irrigation efficiency to paddy rice are as follows; (1) When the standing water irrigation with surface water is practised, the daily average water temperature in a paddy field is 25.2$^{\circ}C$, but, when the gravity flow method is practised with the same irrigation water, the daily average water temperature is 24.5$^{\circ}C$. This means that the former is 0.7$^{\circ}C$ higher than the latter. On the other hand, when ground water is used, the daily water temperatures in a paddy field are respectively 21.$0^{\circ}C$ and 19.3$^{\circ}C$ by practising standing water and the gravity flow method. It can be seen that the former is approximately 1.$0^{\circ}C$ higher than the latter. (2) When the non-water-logged cultivation is practised, the yield of brown rice is 516.3kg/10a, while the yield of brown rice from ground water irrigation plot throughout the whole irrigation period and surface water irrigation plot are 446.3kg/10a and 556.4kg/10a, respectivelely. This means that there is no significant difference in yields between surface water irrigation practice and non-water-logged cultivation, and also means that non-water-logged cultivation results in a 12.6 percent increase in yield compared with the yield from the ground water irrigation plot. (3) The black and white coloring on the inside surface of the water warming ponds has no substantial effect on the temperature of the water. The average daily water temperatures of the various water warming ponds, having different depths, are expressed as Y=aX+b, while the daily average water temperatures at various depths in a water warming pond are expressed as Y=a(b)x (where Y: the daily average water temperature, a,b: constants depending on the type of water warming pond, X; water depth). As the depth of water warning pond is increased, the diurnal difference of the highest and the lowest water temperature is decreased, and also, the time at which the highest water temperature occurs, is delayed. (4) The degree of warming by using a polyethylene tube, 100m in length and 10cm in diameter, is 4~9$^{\circ}C$. Heat exchange rate of a polyethylene tube is 1.5 times higher than that or a water warming channel. The following equation expresses the water warming mechanism of a polyethylene tube where distance from the tube inlet, time in day and several climatic factors are given: {{{{ theta omega (dwt)= { a}_{0 } (1-e- { x} over { PHI v })+ { 2} atop { SUM from { { n}=1} { { a}_{n } } over { SQRT { 1+ {( n omega PHI) }^{2 } } } } LEFT { sin(n omega t+ { b}_{n }+ { tan}^{-1 }n omega PHI )-e- { x} over { PHI v }sin(n omega LEFT ( t- { x} over {v } RIGHT ) + { b}_{n }+ { tan}^{-1 }n omega PHI ) RIGHT } +e- { x} over { PHI v } theta i}}}}{{{{ { theta }_{$\infty$ }(t)= { { alpha theta }_{a }+ { theta }_{ w'} +(S- { B}_{s } ) { U}_{w } } over { beta } , PHI = { { cpDU}_{ omega } } over {4 beta } }}}} where $\theta$$\omega$; discharged water temperature($^{\circ}C$) $\theta$a; air temperature ($^{\circ}C$) $\theta$$\omega$';ponded water temperature($^{\circ}C$) s ; net solar radiation(ly/min) t ; time(tadian) x; tube length(cm) D; diameter(cm) ao,an,bn;constants determined from $\theta$$\omega$(t) varitation. cp; heat capacity of water(cal/$^{\circ}C$ ㎥) U,Ua; overall heat transfer coefficient(cal/$^{\circ}C$ $\textrm{cm}^2$ min-1) $\omega$;1 velocity of water in a polyethylene tube(cm/min) Bs ; heat exchange rate between water and soil(ly/min)