• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.415-423
• /
• 2006

As the shortage of natural & good quality aggregate for concrete, it is needed development of alternative aggregate. At the present time, the crushed sand is widely used among the alternation aggregate, and the usage of crushed sand will be increased more and more. Generally, crushed sud is produced with wet process in domestic, but some manufacturing companies which are handicapped with local restrict are produced by dry process. In this study, analyzing the facilities of dry crushed sand, the quality properties of dry crushed sand was done by Korean Industrial Standards. Based on the quality results of dry crushed sand, the experiment of concrete with the dry crushed sand which is substitute for sea sand was done. As the results of basic qualities, the amount of 0.08 mm sieve passing ratio was over KS criteria, and the fineness modulus was higher than sea sand, and the other physical properties of dry crushed sand was similar to sea sand. The results of concrete experiment, according to the substitutive ratio of dry crushed sand is increased, the slump and air content of concrete was decreased by increase of fine particles of dry crushed sand, and the unit weight content, compressive & tensile strength of concrete were increased on the contrary. The physical properties of concrete used dry crushed sand were showed same tendency without relation to W/B. Consequently, if the fine particle contents of dry crushed sand was lower, it is judged that dry crushed sand is no problem to use for concrete aggregate and the amount of usage will be increased.

• Toxicological Research
• /
• v.28 no.1
• /
• pp.25-31
• /
• 2012

The purpose of this study was to determine the acute pulmonary toxicity of metallic silver nanoparticles (MSNPs, 20.30 nm in diameter). Acute pulmonary toxicity and body distribution of inhaled MSNPs in mice were evaluated using a nose-only exposure chamber (NOEC) system. Bronchoalveolar lavage (BAL) fluid analysis, Western blotting, histopathological changes, and silver burdens in various organs were determined in mice. Mice were exposed to MSNPs for 6 hrs. The mean concentration, total surface area, volume and mass concentrations in the NOEC were maintained at $1.93{\times}10^7$ particles/$cm^3$, $1.09{\times}10^{10}\;nm^2/cm^3$, $2.72{\times}10^{11}\;nm^3/cm^3$, and 2854.62 ${\mu}g/m^3$, respectively. Inhalation of MSPNs caused mild pulmonary toxicity with distribution of silver in various organs but the silver burdens decreased rapidly at 24-hrs post-exposure in the lung. Furthermore, inhaled MSNPs induced activation of mitogen-activated protein kinase (MAPK) signaling in the lung. In summary, single inhaled MSNPs caused mild pulmonary toxicity, which was associated with activated MAPK signaling. Taken together, our results suggest that the inhalation toxicity of MSNPs should be carefully considered at the molecular level.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.1
• /
• pp.109-120
• /
• 2000

In the analysis of the common categories, moisture contents and organic concentrations were not much different according to the types of industry or treatment facilities. When heavy metals contribution of the sludge from domestic and industrial wastewater treatment facilities was analyzed, As, Hg and Cr concentrations were relatively high among 42 standards of the fertilizer law. As concentration war higher in 28 of 42 facilities (67%) than limits of the fertilizer law. Hg concentration was not acceptable in the 21 of 42 facilities (50%). Cr concentration was not acceptable in 9 of 42 facilities (21%). From these results, It is found that As is the most frequently detectable component and contaminant than any other heavy metals in sludges. The data from this experiment was also compared with the guidelines of harmful organics and the rest of heavy metals that are regulated by some of the foreign countries. Be, Se and Mo concentrations were lower than the limits. Among the organics, the average concentration of PCB (10 samples) was 26.2 ppb. The highest concentration was 162.6 ppb in the sludge of the municipal wastewater treatment facilities and the lowest concentration was 2.14 ppb from the skin manufacturing industry. From the leaching analysis of re-manufacturing goods from the sludge, most of them was acceptable on the regulation law but Cr concentration was over the limit.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.5
• /
• pp.55-63
• /
• 2018

Recently, the use of duplex stainless steel which with a two-phase microstructure (equal mixture of ferrite and austenite) has been increased in a variety of industrial fields due to higher strength leading to weight saving, greater corrosion resistance(particularly, stress corrosion cracking) and lower price. However, currently, stainless steels are not included in the structural materials of Korean Building Code and corresponding design standards are not specified. In this paper, experimental studies have been performed to investigate the structural behaviors of duplex stainless steel (STS329FLD) bolted connection with two bolts for providing the design data. Main variables are shear connection type (single shear and double shear) and end distance parallel to the direction of applied force. Fracture modes at the final step of test were classified into typical block shear fracture, tensile fracture and curling. Curling occurrence in single shear connection led to ultimate strength drop by up to 20%. Test strengths were compared with those by current design specifications such as AISC/AISI/KBC, EC3 and AIJ and proposed equations by existing studies. For specimens with no curling, Clement & Teh's equation considering the active shear plane provided a higher strength estimation accurancy and for specimens with curling, Kim & Lim's equation considering strength reduction by curling was also overly unconservative to predict the ultimate strength of curled connections.

• Industry Promotion Research
• /
• v.6 no.2
• /
• pp.55-62
• /
• 2021

The number of single-parent families in South Korea increased since 2000, related to a sharp rise in the divorce rate of 50s and an increase in male mortality rates among those aged 40s-50s. Middle-aged single mothers experience a critical period realizing self-actualization needs, while being in the middle adulthood from the lifespan developmental perspective. In this respect, it is significant to study self-actualization of middle-aged single mothers through guided imagery and music (GIM) in order to provide them with psychological support. This study was conducted from September 2018 to June 2020, and the GIM sessions were conducted at least 10 times. Four participants were selected among the middle-aged single mothers. The imagery experiences of participants in the GIM sessions were classified into four sub-elements: physicalness, emotion, memory, and sense. Within those sub-elements, eight semantic units were categorized into 46 elements. Finally, 152 semantic units were derived. Moreover, the self-actualization which participants experienced through GIM presented three archetypal images: shadow, persona, and the self. In the GIM sessions, experiences of putting their negative emotions associated with family into words and changing passive self-imagery into active one enabled participants to bring the shadow into their consciousness, there by recognizing their positive and bright internal self. Furthermore, participants could map that their current status as people marginalized by siblings and parents, enraged and holding double standards for others, was suppressed by their 'good daughter' and 'religious' personas. This realization lead them to realize and restore their persona. The use of GIM in the study allowed participants to elicit re-experiences of the negative events, while experiencing various imagery and music. This process helped participants achieve self-actualization.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.51 no.5
• /
• pp.1-12
• /
• 2023

This study evaluated the overturning stability of portable tripod ladders used for high-altitude work such as tree management and pruning work in landscaping construction and management. Portable tripod ladders, which are included in general mobile or portable ladders frequently used in industrial sites, are supported in a triangular support structure, not a 4-point support like common A-type Ladders. In addition, since the working height is more than twice that of a mobile or portable ladder, the possibility of an overturning accident that threatens the safety of workers with a fall accident is high. Therefore, based on the overturning stability test specified in ANSI-ASC A14.7 and EN 131-Part 7, which are related standards for about 130 types of portable tripod ladders sold and used in Korea. An equation to calculate each moment according to working height was derived. Then, each calculated moment was compared to evaluate the safety factor for overturning and stability. As a result of the overturning stability evaluation according to each standard, when the provisions of EN 131-Part 7 were applied, portable tripod ladders with 8 steps in the rear direction and 6 steps or more in the side direction were evaluated as unstable against overturning, but according to ANSI-ASC A14.7 regulations. It was evaluated that the stability against overturning was secured in all directions and number of steps.

• Korean Journal of Agricultural Science
• /
• v.50 no.3
• /
• pp.425-436
• /
• 2023

In Korea, the U.S. Tier-4 Final emission standards have been applied to agricultural machinery since 2015. This study was conducted to analyze the emission characteristics of agricultural tractors during plow tillage operations using PEMS (portable emissions measurement systems). The tractor working speed was set as M2 (5.95 km/h) and M3 (7.60 km/h), which was the most used gear stage during plow tillage operation. An engine idling test was conducted before the plow tillage operation was conducted because the level of emissions differed depending on the temperature of the engine (cold and hot states). The estimated level of emissions for the regular area (660 m²), which was the typical area of cultivation, was based on an implement width of 2.15 m and distance from the work area of 2.2 m. As a result, average emission of CO (carbon monoxide), THC (total hydrocarbons), NOx (nitric oxides), and PM (particulate matter) were approximately 6.17×10-2, 3.36×10^-4, 2.01×10^-4, and 6.85×10^-6 g/s, respectively. Based on the regular area, the total emission of CO, THC, NOx, and PM was 2.62, 3.76×10^-2, 1.63, and 2.59×10^-4 g, respectively. The results of total emission during plow tillage were compared to Tier 4 emission regulation limits. Tier 4 emission regulation limits means maximum value of the emission per consumption power (g/kWh), calculated as ratio of the emission and consumption power. Therefore, the total emission was converted to the emission per power using the rated power of the tractor. The emission per power was found to be satisfied below Tier 4 emission regulation limits for each emission gas. It is necessary to measure data by applying various test modes in the future and utilize them to calculate emission because the emission depends on various variables such as measurement environment and test mode.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.9-15
• /
• 2016

We investigated >$50-{\mu}m$ marine planktonic organisms (mainly zooplankton) using a bongo net in Masan Bay and Jangmok Bay in order to harvest 75% of natural communities based on Phase-II approval regulations by the United States Coast Guard (USCG). The concentrated volume (in 1 ton) and abundance of zooplankton were $1.8{\times}10^7ind.ton^{-1}$ and $2.3{\times}10^7ind.ton^{-1}$, and their survival rates were 82.6% and 80.1%, respectively. The community structure in Jangmok Bay was similar to that in Masan Bay, and dominant species were adult and immature groups (stage IV) of genus Acartia. Harvested populations were inoculated in a 500-ton test tank. Although the population abundances were $6.0{\times}10^4ind.ton^{-1}$ for both bay samples, the mortality rates were higher in the Masan Bay population (32%) than the Jangmok Bay population (20%). We considered the reason to be that there were 30% more immature individuals of Acartia from Masan Bay than from Jangmok Bay. The younger population may have been greatly stressed by the moving process and netting gear. After applying a Ballast Water Treatment System (BWTS) using a sample form Jangmok Bay, the mortality rates in the treatment groups were found to be 100% after 0 days and 5 days, implying that the BWTS worked well. During the winter season, the zooplankton concentration method alone did not easily satisfy the approval standards of USCG Phase II (> $10{\times}10^4ind.ton^{-1}$ in the 500 ton tank). Increasing the netting frequency and additional fishing boats may be helpful in meeting the USCG Phase II biological criteria.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3514-3523
• /
• 2009

Before 1990's, Korea had only few colleges that had film and film related majors. As Korean film industry started its marvelous improvement in both commercial and artistic phase, many colleges were interested in this new academic field. They hurried up to launch this new and profitable major; as a result, Korea now has more than hundred colleges and universities that has film related majors. Each college enumerates numbers of academic courses that may look reasonable; they have almost every course a fine film school should provide such as film theory, production, and performance in film. Lots of film schools offer lots of film courses; and they look alike. One unique thing in film major is its vast sub fields and categories. After you decide to study film, you have to select what specific field in film you want to study. Studying film theory and film production can be as different as majoring physics and physical education. The problem Korean colleges are dealing with is that there are too much film schools, and moreover those colleges have similar curriculums that just look like a department store that sells everything. One suggestion is specializing its curriculum in which the school can take advantages using their special conditions. San Francisco Art Institute is one of United States well known private film schools, but many people remember this school as a specialized film school in experimental film. San Francisco where this school is located has had many liberal and experimental artists as the city has been supporting and offering them an environment they can concentrate their work. Naturally, the school has world famous faculty members in experimental film, and students who want to study and make experimental film come to this school from all over the world because they know this school would be the best to study experimental film. There are many film schools in metro Los Angeles area; since its location near Hollywood, no wonder these schools concentrate on film producing and film production. They take advantage of their geographical location to hire film industry professional and to focus on commercial feature film productions. What we can do now to adjust the curriculum in film and film related major in Korean colleges is to adapt new standards in this changed film industry. One school can emphasize digital production while another school focuses on digital intermediate process. But if one school tries to both fields or all fields of film major just like we have done so far, the school could not take care of all the equipment and the faculty that the fields would need. Korean film schools should devide the field in film major and concentrate what they selected. Selection and concentration can be and should be applied in Korean film schools.

• Journal of Intelligence and Information Systems
• /
• v.19 no.2
• /
• pp.177-189
• /
• 2013

In Smart Education, the roles of digital textbook is very important as face-to-face media to learners. The standardization of digital textbook will promote the industrialization of digital textbook for contents providers and distributers as well as learner and instructors. In this study, the following three objectives-oriented digital textbooks are looking for ways to standardize. (1) digital textbooks should undertake the role of the media for blended learning which supports on-off classes, should be operating on common EPUB viewer without special dedicated viewer, should utilize the existing framework of the e-learning learning contents and learning management. The reason to consider the EPUB as the standard for digital textbooks is that digital textbooks don't need to specify antoher standard for the form of books, and can take advantage od industrial base with EPUB standards-rich content and distribution structure (2) digital textbooks should provide a low-cost open market service that are currently available as the standard open software (3) To provide appropriate learning feedback information to students, digital textbooks should provide a foundation which accumulates and manages all the learning activity information according to standard infrastructure for educational Big Data processing. In this study, the digital textbook in a smart education environment was referred to open digital textbook. The components of open digital textbooks service framework are (1) digital textbook terminals such as smart pad, smart TVs, smart phones, PC, etc., (2) digital textbooks platform to show and perform digital contents on digital textbook terminals, (3) learning contents repository, which exist on the cloud, maintains accredited learning, (4) App Store providing and distributing secondary learning contents and learning tools by learning contents developing companies, and (5) LMS as a learning support/management tool which on-site class teacher use for creating classroom instruction materials. In addition, locating all of the hardware and software implement a smart education service within the cloud must have take advantage of the cloud computing for efficient management and reducing expense. The open digital textbooks of smart education is consdered as providing e-book style interface of LMS to learners. In open digital textbooks, the representation of text, image, audio, video, equations, etc. is basic function. But painting, writing, problem solving, etc are beyond the capabilities of a simple e-book. The Communication of teacher-to-student, learner-to-learnert, tems-to-team is required by using the open digital textbook. To represent student demographics, portfolio information, and class information, the standard used in e-learning is desirable. To process learner tracking information about the activities of the learner for LMS(Learning Management System), open digital textbook must have the recording function and the commnincating function with LMS. DRM is a function for protecting various copyright. Currently DRMs of e-boook are controlled by the corresponding book viewer. If open digital textbook admitt DRM that is used in a variety of different DRM standards of various e-book viewer, the implementation of redundant features can be avoided. Security/privacy functions are required to protect information about the study or instruction from a third party UDL (Universal Design for Learning) is learning support function for those with disabilities have difficulty in learning courses. The open digital textbook, which is based on E-book standard EPUB 3.0, must (1) record the learning activity log information, and (2) communicate with the server to support the learning activity. While the recording function and the communication function, which is not determined on current standards, is implemented as a JavaScript and is utilized in the current EPUB 3.0 viewer, ths strategy of proposing such recording and communication functions as the next generation of e-book standard, or special standard (EPUB 3.0 for education) is needed. Future research in this study will implement open source program with the proposed open digital textbook standard and present a new educational services including Big Data analysis.