• 대한토목학회논문집
• /
• 제26권1A호
• /
• pp.99-106
• /
• 2006

일축대칭의 단면특성을 갖는 T형 부재는 단면의 특성상 축방향 압축력으로 인하여 전체좌굴이 발생할 경우 휨-비틀림 좌굴이 지배모드가 된다. 인발성형 T형 부재의 휨-비틀림 좌굴거동을 실험적 연구를 통하여 알아보았다. E-glass/vinylester와 E-glass/polyester로 만들어진 2종류의 인발성형 부재가 사용되었으며, 보강층의 배치, 보강층의 두께, 구성물질의 부피비, 역학적 성질 등을 실험적으로 규명하였다. 좌굴실험에서 휨 및 비틀림에 대한 단순지지 조건을 만족시키기 위해서 knife edge를 사용하였으며, 3개의 potentiometer를 사용하여 실험체의 횡변위와 비틀림각을 측정하였다. 모든 실험체에 휨-비틀림 좌굴이 발행하였으며, 대부분의 실험체가 후좌굴 강도를 가지고 있음을 알 수 있었다.

• 대한수사과학회지
• /
• 제1권2호
• /
• pp.31-43
• /
• 2006

최근 살인사건의 실태를 보면 칼을 이용한 살인사건이 가장 많다. 살인을 음모하고 예견된 살인도 있지만, 순간적인 분노로 인한 우발적으로 저질러지기도 한다. 우발적인 범행에서 주변 가까이에 있는 가정용 칼을 범행에 사용하는 경우가 많지만 일상생활에서 칼의 위험성을 인식하는 경우가 드물다. 이에 전국에서 발생하는 살인사건의 범행방법 중 칼에 의한 범행에서 동기 분석과 함께 살해에 사용한 칼의 종류를 분석하였다. 그리고 칼에 대한 인식을 알아보고자 성인 남녀 500명을 대상으로 가정용 칼에 대한 21항목의 설문조사를 실시하였다. 그 결과를 일반 가정에서 사용하는 칼의 대부분이 칼끝이 날카로워 사실상 범행에 사용하기가 용이하였다. 그렇기 때문에 범인들이 칼을 휴대하기보다는 범행 장소에서 칼을 쉽게 구하여 범행에 사용하는 경우가 많다. 그리고 우발적인 살인의 경우에도 주방이나 식탁 또는 거실에서 칼을 쉽게 구할 수 있기 때문에 살인 사건이 더욱 빈발할 수 있다. 일반인의 칼에 대한 인식에서 칼의 위험도를 낮추기 위하여 칼끝을 둥글게 하자는 여론은 매우 높은 결과로 나타나지만 실제로 칼의 위험성에 대한 인식이 낮았다. 따라서 가정이나 가까운 사이에서 우발적 충동적인 살인을 예방하기 위하여 생활도구로 사용하는 칼도 위험한 물건으로 분류하여 인식전환과 함께 칼의 제작과 판매에 있어서 적절한 규제가 필요하다고 생각한다. 칼에 대한 인식을 새롭게 하여 가정에서 칼의 보관과 잠금장치의 필요성에 대한 홍보가 절실하다고 생각한다.

• 대한치과보철학회지
• /
• 제29권3호
• /
• pp.101-110
• /
• 1991

The purpose of this study was to compare the repaired joint strength among several edge profiles after denture repair. For this study, eight edge profiles were used for repair methods and five self-curing resin brands were used for repair materials. Break away loads were tested after 1 hr., 24 hrs. and 1 week. Instron was used for testing the transverse strength of repaired specimen. The results were as follows. 1. Repaired joint strength was about 35-65% of that of original specimen. 2. Joint strengths of round, inverse knife, inverse rabbit, lap ogee joint were higher tnan that of traditional simple butt joint 3. Joint strength of the simple butt joint was low significant. 4. Joint strengths after 1 hr. specimen were lower than those of 24 hrs. and 1 week specimens in joint strengths. 5. There were no significant differences between 24 hrs. and 1 week specimens in joint strengths. 6. It look more than 24 hours to gain satisfactory physical property after repairing the fractured denture base when self-curing resin was used for repair.

• Journal of the Optical Society of Korea
• /
• 제19권1호
• /
• pp.7-12
• /
• 2015

Up to ${\sim}520{\mu}J$ broadband mid-infrared (IR) supercontinuum (SC) generation in telecommunication multimode fiber (MMF) directly pumped by a $2.054{\mu}m$ nanosecond Q-switched Tm, $Ho:YVO_4$ laser is demonstrated. An average output power of 3.64 W is obtained in the band of ~1900 to ~2600 nm, and the corresponding optic-to-optic conversion efficiency is 67% by considering the coupling efficiency. The spectrum has extremely high flatness with negligible intensity variation (<2%) in the wavelength interval of ~2070 to ~2475 nm. The SC long-wavelength edge is limited by the silicon glass material loss, and by optimizing the MMF length, the SC spectrum could extend out to ${\sim}2.6{\mu}m$. The output SC pulse shapes are measured at different output powers, and no splits are found. The SC laser beam is nearly diffraction limited with an $M^2=1.15$ in $2.1{\mu}m$ measured by the traveling knife-edge method, and the laser beam spot is monitored by an infrared vidicon camera.

• 대한치과기공학회지
• /
• 제22권1호
• /
• pp.79-88
• /
• 2000

The objective of this finite element method study was to analyze the stress distribution induced in a maxillary central incisor Ni-Cr base metal coping ceramic crowns with various margin design. Margin designs of crown in this experiment were knife-edge metal margin on chamfer finishing line of tooth preparation(M1), butt metal margin on shoulder finishing line(M2), reinforced butt metal margin on shoulder finishing line(M3), beveled metal margin on bevelde shoulder finishing line(M4). Two- dimensional finite element models of crown designs were subjected to a simulated biting force of 100N which was forced over porcelain near the lingual incisal edge. Base on plane stress analysis, the maxium von Miss stresses(Mpa) in porcelain venner was 0.432, in metal coping was 0.579, in dentin abutment was 0.324 for M1 model, and M2 model revealed in porcelain was 0.556, in metal coping was 0.511, in dentin was 0.339, and M3 model revealed in porcelain was 0.556, in metal coping was 0.794, in dentin was 0.383 for M4 model. All values of each material in metal-ceramic crown were much below the critical failure values.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.14-19
• /
• 2011

Wind tunnel tests are performed so as to investigate the aerodynamic drag characteristics of HEMU-400x, next generation Korean high speed train. The experiments of 1/20 scaled 5-car train model are done at 30, 40, 50, 60m/s with a normal bogie, a bogie cover, and a streamlined shape. The flat plate with knife edge are installed to minimize the effect of boundary layer of wind tunnel for the train model. The aerodynamic drag reduction was more by a streamlined shape than by a bogie cover from a normal bogie. Based on the experimental results, the aerodynamic drag of HEMU-400x test train(6-car) was predicted. It is prediceted that More bogie cover could reduce more aerodynamic drag of the test train in replacement of normal bogies.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2002년도 하계학술발표회
• /
• pp.24-25
• /
• 2002

밀레니움을 전후하여 세계적으로 8m급 초대형 망원경들이 만들어지고 있다. ESO (European Southern Observatory)의 VLT (Very Large Telescopes) 4기, 미국 영국 카나다 등의 연합 Gemini telescope 2기, 일본의 Subaru 1기 등, 10여기의 망원경들이 완성되었고, 차세대 망원경들이 50m급으로 디자인되고 있다. 우주망원경도 지름 2.4m인 허블 우주망원경(Nubble Space Telescope)의 뒤를 이어 6m급의 차세대 우주망원경 (Next Generation Space Telescope)이 개발되고 있어서 2010년경에 발사될 예정이다. (중략)

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2003년도 한국우주과학회보 제12권2호
• /
• pp.27-27
• /
• 2003

The Automated Quantitative Knife-Edge Test (AQuaKET) method was developed for testing the surface profiles of large optics with high accuracy. Testing with the required accuracy of very large telescope is not an easy job to achieve, as it is a nano-technology. There are lots of possible error sources which can occur during the measurements and in the data processing of the AQuaKET. The error sources can be categorized into 5 areas: optics, mechanics, electronics, numerical processes, and system. In this paper, possible error sources in Optics are discussed, which are intensity variation of the light source, diffraction effects, and parallax effect. In this talk, those possible error sources in optics are presented and discussed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.291-292
• /
• 2006

Currently A demand of high precision workpiece is increasing in industry. At present, roundness measuring machine using Air bearing, coordinate measuring machine that are used from measurement station. but these machines will not be able to apply to In-line process. because of like these machine's price are very expensive and measurement time is long. also, the complexity of conventional roundness measurement method based on fourier transform, it makes difficult to development analysis program. This work present new architecture of a Out-diameter measuring system fur analysis of roundness of product. In this system, the influence of table motion errors is minimize by using two LVDT sensor and knife edge contact tip. We are produce a test machine and make an experimenter on Out-diameter of test bearing. The measurement result compared with roundness measuring machine.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.594-596
• /
• 2000

The best simulation condition for the fiber collimator that uses ball lenses was investigated. This kind of fiber collimator can be used in a Micro-Optical-Cross-Connects(MOXC). MOXC is composed of collimating ball lenses, micro mirrors and single-mode fibers. In order to design a MOXC, it is very important to calculate beam path, beam radius, divergence angle that determines the insertion loss of the MOXC. Since the beam profile from the fiber facet is not exact Gaussian profile, it was found that the simulation condition in which beam waist exists on the fiber facet, ignoring Numerical Aperture(NA), gives best agreement with the experimental results. Beam radii were measured with conventional knife edge method.