• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1327-1337
• /
• 2018

Aviation fuel oil is more strictly controlled than other transport fuels because it can lead to major accidents in the event of a problem. The quality standards of the aircraft are specified by the domestic Korean Standard, the American Society for Testing and Materials and the International Air Transport Association, respectively. From 2016 to 2017, the quality analysis of 6 items such as aromatic content, sulfur content and distillation characteristics was carried out on the jet fuel produced at five domestic refineries. Domestic production of jet fuel has been shown to be in conformity with the quality standards and has been maintained at a constant level throughout the year. Compared with the specification of ASTM and IATA the aromatic content of domestic KS specification is set to be strictly 1.5 wt% higher than the ASTM and IATA setting specification, but it satisfies this specification sufficiently. In addition, other items such as sulfur content, distillation property and flash point satisfied both domestic and international specification.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.9
• /
• pp.35-44
• /
• 2022

The cyclic triaxial strength test is commonly applied as a laboratory test for evaluating the liquefaction resistance ratio. However, the test procedure was not standardized in South Korea until recently; thus, the test results could significantly differ depending on the performer and apparatus, even when identical soil is used. In this study, the American and Japanese standards for the cyclic triaxial strength test were analyzed and the Korean standard was developed considering domestic circumstances. To verify the effectiveness of the standardization of liquefaction laboratory tests, several cases of cyclic triaxial strength tests were conducted and analyzed (1) following the Korean standard and (2) without following any specific instructions for the test procedure. Under (1), the deviation of the liquefaction resistance ratio dramatically decreased.

• Journal of the Korean Society of Safety
• /
• v.32 no.1
• /
• pp.108-114
• /
• 2017

According to an increase in demand for polyurethane soft foam for thermally insulated containers, the purpose of this study is based on redefining existing rigid polyurethane foam insulation KS standard which has been limited to building material-based authentication techniques. Since there are arising concerns of consumer rights and safety due to humidifier fungicides and urethane track incidents, there are elements to be further researched on rigid polyurethane foam insulation for refregerated containers. Thus, we reviewed the prior standards for rigid polyurethane foam insulation and verified the validity of certification testing method for the new standard with self-foamed polyurethane.

• Journal of the Korean housing association
• /
• v.21 no.6
• /
• pp.53-60
• /
• 2010

Built-in wardrobe is constructing after ordering and making, because built-in wardrobe's size is fixed as housing measurement. It is hard to speak built-in wardrobe components of construction in these ways, and application of an MC (Modular Coordination) design system is meaningless too. And above all, measurement before construction isn't to expect standardization, and to increase custom-made furniture. So I suggest the standardization of built-in wardrobe utilizing standard last finish and reference plane in order to prevent an evil influence of built-in wardrobe's construction. And we utilized a reference plane, and we present construction document and design plan in order to solve these problems. The first stage, we investigate manufacture of a preferential domestic system kitchen and construction state, and we derive from a problem in viewpoints of standardization for this. And we analyze an effect got by application of the assembly basis aspect that we presented, and we can raise efficiency of standardization of housing and construction industry, and we light ultimately up. I will apply a standardization plan as above, and define that this assures a standardization of components and an economic effect.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.12
• /
• pp.47-54
• /
• 2015

Normally, multiple socket-outlet is manufactured with soldered, welded permanent connection (termination). Because this procedure is very non-environmental and requires many labor forces, many companies skip this process. To solve this these problems, this research had to design permanent joint type multiple socket-outlet, develop safer multiple socket-outlet than is sold in markets. Progressing this research, we took 3 steps. First, we had to design device for fixing a frame suitable for multiple socket-outlet. Second, this multiple socket-outlet must pass fundamental standards through international standard (IEC 60884-1) and Korean standard (K 60884-1) tests. Third, it had to pass both several mechanical and electrical tests which is more strict than fundamental standards and vibration and impact tests following KS standards for enhancing its safety. After finishing 3 steps, we could obtain objective and fair data, develop environmental permanent joint type multiple socket-outlet without soldering crimped connection.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.255-262
• /
• 2018

Purpose: To obtain the dynamic characteristics (spring stiffness and damping coefficient) of a rubber mount supporting a tractor cabin in order to develop a simulation model of an agricultural tractor. Methods: The KS M 6604 rubber mount test method was used to test the dynamic characteristics of the rubber mount. Of the methods proposed in the standard, the resonance method was used. To perform the test according to the standard, a base excitation test device was constructed and the accelerations were measured. Results: Displacement transmissibility was measured by varying the frequency from 3-30 Hz. The vibration transmissibility at resonance was confirmed, and the dynamic stiffness and damping coefficient of the rubber mount were obtained. The front rubber mount has a spring constant of 1247 N/mm and damping ratio of 3.27 Ns/mm, and the rear rubber mount has a spring constant of 702 N/mm and damping ratio of 1.92 Ns/mm. Conclusions: The parameters in the z-direction were obtained in this study. In future studies, we will develop a more complete tractor simulation model if the parameters for the x- and y-directions can be obtained.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.551-556
• /
• 2018

The material normally used in hot dip galvanizing facilities is SM45C (carbon steel for mechanical structure, KS standard), mainly because of its price. During this process, the oxidation of the plating facility occurs due to the heat of the Zn fumes coming from the molten zinc. Since the cycle time of the current facilities is 6 months, much time and money are wasted. In this study, the corrosive properties of various materials (Inconel625, STS304, SM45C) were investigated by oxidation in a high temperature and Zn fumes environment. The possibility of applying the hot-dip galvanizing equipment was investigated for each material. The Zn fumes were generated by directly bubbling Ar gas into Zn molten metal in a 650 degree furnace. High-temperature, Zn fumes corrosion was conducted for 30 days. The sample was removed after 30 days and the oxidation of the surface was confirmed with EDS and SEM, and the corrosion properties were examined using potentiodynamic polarization tests.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.2 s.25
• /
• pp.7-12
• /
• 2007

This study has been conducted to present reform recommendations for Standardization of Construction Materials, based on a study on the Investigation of Demander's Consciousness for Construction Materials Quality and Information Standardization in Korea. Upon investigation, it was found that the quality of Korea Industrial Standards (KS) was given 67 points (out of 100) by respondents. In addition, 38% of the respondents showed that they had problems with a lack of Standardized Information. Good examples were found to be non-standardized materials, e.g. admixtures, waterproof agents, reinforcing fibers, concrete, aggregates, adhesives, wood, temporary materials, thermal-insulating materials, etc. Upon results from the investigation of demander's consciousness for infrastructure of standardization of information, 71.2% of respondents thought that it is necessary to informatize construction materials. They made following demands on the informatization to be, in order: Quality, Standard, Price (Cost), Operation, Drawing, Law, and Information.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7773-7780
• /
• 2015

Analysis of existing kettle and its heating system has been the topic for localization technology development. Test pieces are made, polished and etched for existing kettle analysis. Surface of test pieces is observed using SEM, the kettle is verified to be made by deep drawing process from Ferrite-Perlite material. The kettle is also identified to be plated $16{\sim}49{\mu}m$ of thickness with Nickel(16%). Also heat transfer characteristics based on hot wire arrangement is investigated and optimal hot wire system is developed. Developed control system detects overheating and stops the whole system on the long operating time. Developed kettle takes the performance evaluation test for volume expansion and satisfied for standard 'KS G3602'.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.63-71
• /
• 2018

Strands with ultimate strength of 2,400 MPa was developed and applied in the KCI Code and the KS standard. A high-strength prestressed strand to be applied to a structure, a suitable anchorage system should be used together. Recently, a post tension anchorage for 2,400 MPa strands was developed. but there is not much research on performance evaluation. Therefore, in this study, structural analysis of local zone with 9 strands, 15 strands, and 19 strands anchorage were investigated respectively, which are most widely used for post tensioning anchorages with 2,400 MPa strands, according to PTI anchorage zone design method, and Load transfer performance from ETAG013 and/or KCI-PS101 was evaluated. Furthermore, the adequacy of the test was also analyzed by nonlinear numerical analysis. As results, the anchorages with 2,400 MPa strands satisfied the structural performance of the local area and satisfied the load transfer performance condition.