• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.4
• /
• pp.247-252
• /
• 2016

In this paper, we propose a new defect detection technology for micro-defect on the surface of steel products. Due to depth and size of microscopic defect, slop of surface and vibration of strip, the conventional optical method cannot guarantee the detection performance. To solve the above-mentioned problems and increase signal to noise ratio, a novel retro-schlieren method that consists of retro reflector and knife edge is proposed. Moreover dual switching lighting method is also applied to distinguish uneven micro defects and surface noise. In proposed method, defective regions are represented by a black and white pattern. This pattern is detected by a defect detection algorithm with Gabor filter. Experimental results by simulator for sample defects of cold rolled steel show that the proposed method is effective.

• Nuclear Engineering and Technology
• /
• v.49 no.6
• /
• pp.1354-1357
• /
• 2017

Characterization of special nuclear material may be performed using energy spectroscopy of either the neutron or gamma-ray emissions from the sample. Gamma-ray spectroscopy can be performed relatively easily using high-resolution semiconductors such as high-purity germanium. Neutron spectroscopy, by contrast, is a complex inverse problem. Here, results are presented for $^{252}Cf$ and PuBe energy spectra unfolded using a single EJ309 organic scintillator; excellent agreement is observed with the reference spectra. Neutron energy spectroscopy is also possible using a two-plane detector array, whereby time-of-flight kinematics can be used. With this system, energy spectra can also be obtained as a function of position. Spatial-dependent energy spectra are presented for neutron and gamma-ray sources that are in excellent agreement with expectations.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.249-252
• /
• 2006

Wind turbine gearbox is a complex mechanical system that includes gear trains, shafts, bearings, and gearbox housings. All these component are interacting with each other therefore changing certain design parameter will affect other components. RomaxDesigner enables a reduction in development period by simulating the full gearbox system. The gear pairs, bearings and shafts are represented as analysis objects and the complex components are modelled by means of reduced stiffness matrices. The software allows durability analysis and advanced contact analysis including the effects of system misalignments in gear and bearing. In this paper the 2MW wind turbine gearbox was model led and a study on optimum design was conducted

• Analytical Science and Technology
• /
• v.30 no.5
• /
• pp.252-261
• /
• 2017

Naturally occurring radioactive materials (NORMs) increase radiation exposure to the public as these materials are concentrated through artificial manufacturing processes by human activities. This study focuses on the development of a method for the quantitative analysis of $^{232}Th$, $^{235}U$, and $^{238}U$ in building materials. The accuracy and precision of inductively coupled plasma mass spectrometry (ICP-MS) for determination of digestion processes was evaluated for certified reference materials (CRMs) digested using various mixed acid (e.g., aqua regia, hydrofluoric acid, and perchloric acid) digestions and a $LiBO_2$ fusion method. The method validation results reveal that a $LiBO_2$ fusion and $Fe(OH)_3$ co-precipitation should be applied as the optimal sample digestion process for the quantitative analysis of radionuclides in building materials. The radioactivity of $^{232}Th$, $^{235}U$, and $^{238}U$ in a total of 51 building material (e.g., board, brick, cement, paint, tile, and wall paper) samples was quantitatively analyzed using an established process. Finally, the values of $^{238}U$ and $^{232}Th$ radioactivity were comprehensively compared with those from the indirect method using ${\gamma}$-spectrometry.

• Progress in Medical Physics
• /
• v.26 no.2
• /
• pp.112-117
• /
• 2015

In order to establish the quality control on patient safety following the guideline presented by American Association of Physicists in Medicine (AAPM) TG-100 committee, we aim to analyze the modes based on errors occurred during treatment of patients at the radiation oncology department at Yeungnam University Hospital and establish a quality control guideline for patient safety when patient-centered radiation treatment is conducted. We aim to analyze the errors that can occur during radiation treatment at the radiation department, and assess the frequency of error, the severity of error affecting patients, and probability of proceeding without noticing error, with scores. The places where errors can take place were divided into CT simulation treatment room, treatment planning room, and treatment room for the analysis. In CT simulation treatment room, an error from using the immobilization device showed the highest Risk Priority Number (RPN) value of 60, and an error from simulation treatment information input showed the lowest of 6. In treatment planning room, an error from selecting the radiation dose calculation model showed the highest RPN value of 168, and an error of patient treatment start date showed the lowest of 36. In treatment room, a Table Bar error showed the highest RPN value of 252, a weight change error showed 190, and a Pillow error showed the lowest of 24.

• Food Science and Preservation
• /
• v.18 no.3
• /
• pp.341-348
• /
• 2011

The nutritional components and antioxidative activities of jujube fruit and leaf were investigated and analyzed to provide basic data for functional food materialization and processing. The nitrogen-free extract contents of the fruit and leaf were 71.92% and 41.51%, respectively. The mineral components of the fruit and leaf were rich in Ca (72.14 and 3,252.09 mg/100 g), K (899.82 and 1,708.12 mg/100 g), and P (172.11 and 286.28 mg/100 g), respectively. The major free sugars of the fruit were glucose (13.01 %) and fructose (7.35%); and of the leaf, sucrose (3.94%) and fructose (0.75%). The ascorbic acid contents were higher in fruit (135.73 mg/100 g) than in the leaf (100.43 mg/100 g). The analysis of the component amino acid showed a relatively high ratio of glutamic acid, aspartic acid, proline, and essential amino acids of leucine, but a low methionine and cystine content. The ABTS and FRAP assays indicated that the butanol fraction of the leaf was a more potent radical scavenger and reducing agent than the other five solvent fractions. The butanol fraction of the leaf also presented inhibitory effects against lipid peroxidation in a dose-dependent manner. Therefore, this study verified that the butanol fraction of the leaf has strong antioxidative activities that are correlated with its high level of phenolics, particularly rutin and quercitrin. These phenolics of jujube leaf can be utilized as effective and safe functional food substances, i.e., natural antioxidants.

• Tuberculosis and Respiratory Diseases
• /
• v.50 no.2
• /
• pp.252-257
• /
• 2001

Swyer-James syndrome is a rare disease with patients presenting with unilateral hyperlucent lungs due to hypoplasia of the pulmonary artery and bronchiolitis obliterans. A unilateral hyperlucent lung generally develops after a lower respiratory tract infection during early childhood. In extremely rare cases, an association of bronchogenic carcinoma with Swyer-James syndrome has been reported. Here we report a case of bronchogenic squamous cell carcinoma associated with Swyer-James syndrome with a relevant literature review.

• Korean Journal of Environmental Agriculture
• /
• v.32 no.4
• /
• pp.252-259
• /
• 2013

BACKGROUND: Salt accumulation in coastal reclaimed soil can decrease plant growth and productivity, which could lead to considerable variation of methane($CH_4$) emission in a rice paddy. The objective of this study was to evaluate the effect of salt concentration on $CH_4$ emission in a coastal reclaimed soil. METHODS AND RESULTS: The effect of salt concentration on $CH_4$ emission and rice growth characteristics was studied by pot test, which packed by reclaimed paddy soils collected from Galsa, Hadong, Gyeongnam province. Electrical conductivity(EC) of each treatment was controlled by 0.98, 2.25, 5.05 and 9.48 dS/m and $CH_4$ emission was characterized a week interval by closed chamber method during rice cultivation. The $CH_4$ emission rate was significantly decreased with increase of salt accumulation, but total $CH_4$ flux in EC 5.50 dS/m treatment was lower than those of EC 9.48 dS/m treatment. It seems because of higher content of water soluble $SO{_4}^{2-}$ in EC 5.50 dS/m treatment than those of EC 9.48 dS/m treatment. Rice growth and grain yield were significantly decreased with increase of salt accumulation. Soil properties, especially EC and pH were negatively correlated with $CH_4$ flux, while rice growth characteristics like plant height and tiller number show significantly positive correlation with $CH_4$ flux. CONCLUSION(S): Conclusively, salt accumulation significantly decreased $CH_4$ flux in a rice paddy, which could be useful information for evaluating $CH_4$ flux in reclaimed area in Korea.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.1
• /
• pp.250-252
• /
• 2014

Lipoprotein-associated phospholipase A2 (Lp-$PLA_2$) is a crucial enzyme in atherosclerosis as a potential drug target. The most remarkable Lp-$PLA_2$ inhibitory drug is Darapladib. We determined the binding pose of Darapladib to Lp-$PLA_2$ through docking study. Darapladib formed two hydrogen bonding interactions with the side chain of Tyr160 and Gln352 and several pi-pi interactions with aromatic and aliphatic hydrophobic residues of Lp-$PLA_2$. It is known that the dietylpropan-amine moiety of Darapladib has influence on the improvement of its oral bioavailability and we supposed this in our docking results.

• Journal of applied mathematics & informatics
• /
• v.3 no.2
• /
• pp.245-252
• /
• 1996

We described a relationship of the $L_2$ norm of the $L_2$norm of a Bzier curve and l2 norm of its confrol points. The use of Bezier curves finds much application in the general description of curves and surfaces and provided the mathematical basis for many computer graphics system. We define the $L_2$ norm for Bezier curves and find a upper and lower bound for many computer graphics system. We define the $L_2$ norm for Bezier curves and find a upper and lower bound for the $L_2$ norm with respect to the $L_2$ norm for its control points for easy computation.