• 한국토양비료학회지
• /
• 제50권5호
• /
• pp.489-496
• /
• 2017

This study was conducted to test the applicability of hydroxy radical reactor system, which applied advanced oxidation processes, to sterilize pathogenic bacteria for nutrient solution recycling in closed hydroponics. Removal efficiency was tested on 25 L of nutrient solution maxed with 10 mL culture solution of bacteria, E. coli, and R. solanacearum in a pilot tank. The testing conditions included various levels of hydroxy radicals resulting from air flow rates of 40, 80, and $120L\;min^{-1}$, and 12 hours processing time. The removal of bacteria, E. coli, and R. solanacearum by hydroxy radical in nutrient solution was significantly increased with an increase in the flow rate of the air from $40L\;min^{-1}$ to $120L\;min^{-1}$. The optimum removal efficiency was achieved at an air flow rate of $120L\;min^{-1}$ for 2 hours treatment. There were no significant differences in removal efficiency among bacteria, E. coli, and R. solanacearum for tested level and time of hydroxy radical. These results verified the efficiency of hydroxy radical in removing the pathogenic bacteria and the applicability of hydroxy radical reactor system in the field.

• Journal of Chest Surgery
• /
• 제44권6호
• /
• pp.418-422
• /
• 2011

Background: It has recently become most general to use the small bore catheter to perform closed thoracostomy in treating iatrogenic pneumothorax. This study was performed for analysis of the efficacy of treatment methods by using small bore catheter such as 7 F (French) central venous catheter, 10 F trocar catheter, 12 F pigtail catheter and for analysis of the appropriateness of each procedure. Materials and Methods: From March 2007 to February 2010, Retrospective review of 105 patients with iatrogenic pneumothorax, who underwent closed thoracostomy by using small bore catheter, was performed. We analyzed the total success rate for all procedures as well as the individual success rate for each procedure, and analyzed the cause of failure, additional treatment method for failure, influential factors of treatment outcome, and complications. Results: The most common causes of iatrogenic pneumothorax were presented as percutaneous needle aspiration(PCNA) in 48 cases (45.7%), and central venous catheterization in 26 cases (24.8%). The mean interval to thoracostomy after the procedure was measured as 5.2 hours (1~34 hours). Total success rate of thoracostomy was 78.1%. The success rate was not significantly difference by tube type, with 7 F central venous catheter as 80%, 10 F trocar catheter as 81.6%, and 12 F pigtail catheter as 71%. Twenty one out of 23 patients that had failed with small bore catheter treatment added large bore conventional thoracostomy, and another 2 patients received surgery. The causes for treatment failure were presented as continuous air leakage in 12 cases (52.2%) and tube malfunction in 7 cases (30%). The causes for failure did not present significant differences by tube type. Statistically significant factors affecting treatment performance were not discovered. Conclusion: Closed thoracostomy with small bore catheter proved to be effective for iatrogenic pneumothorax. The success rate was not difference for each type. However, it is important to select the appropriate catheter by considering the patient status, pneumothorax aspect, and medical personnel in the cardiothoracic surgery department of the relevant hospital.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.18-23
• /
• 2016

Injection molded thermoplastic parts may need to be coated to facilitate paint adhesion, or to satisfy other surface property requirements, such as appearance, durability, and weather resistance. In this paper, a two-component polyurethane metering system was developed for the simultaneous injection and surface coating of a plastic substrate. The system was composed of storage tanks, feed pumps, axial piston pumps, mixing head. The tank was designed to be double-jacket structured and fabricated for polyol and isocyanate, respectively. A temperature chamber was used to maintain the material temperature to be $80^{\circ}C$ during flowing from storage tank to mixing head. Inside the chamber, feed pump, low pressure filter, high pressure pump, high pressure filter, pressure sensor, flow meter were installed. A mixing head of L-type was used for homogeneous mixing of polyol and isocyanate. Inside the mixing head, a cartridge heater and a temperature sensor were installed to control the temperature of the materials. The flow rate of axial-piston pump was controlled by using closed-loop feedback control algorithm. The input flow-rates were compared with the measured values. The output error was 6.7% for open-loop control, whereas the error was below 2.2% for closed-loop control. In addition, the pressure generated through mixing-head nozzle increased with increasing flow rate. It was found that the pressure drop between metering pump and mixing-head nozzle was almost 10 bar.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.239-244
• /
• 2003

This study concerns the performance of condensing heat transfer in two-phase closed thermosyphons with various helical grooves. Distilled water, methanol, ethanol have been used as the working fluid. In the present work, a copper tube of the length of 1200mm and 14.28mm of inside diameter is used as the container of the thermosyphon. Each of the evaporator and the condenser section has a length of 550mm, while the remaining part of the thermosyphon tube is adiabatic section. A experimental study was carried out for analyzing the performances of having 50, 60, 70, 80, 90 helical grooves. A plain thermosyphon having the same inner and outer diameter as the grooved thermosyphons is also tested for the comparison. The type of working fluid and the numbers of grooves of the thermosyphons with various helical grooves have been used as the experimental parameters. The experimental results have been assessed and compared with existing theories. The results show that the type of working fluids are very important factors for the operation of thermosyphons. And the maximum enhancement (i.e. the ratio of the heat transfer coefficients the helical thermosyphons to plain thermosyphons) is $1.5{\sim}2$ for condensation.

• 전기전자학회논문지
• /
• 제2권2호
• /
• pp.299-308
• /
• 1998

본 논문에서는 신뢰할 수 있는 SRM 구동시스템과 기존의 PI제어기에 4개의 규칙으로 이루어진 FLM(Fuzzy Logic Modifier)를 제안하였다. 저가격 원칩 마이크로컨트롤러인 인텔사의 i80C196KC는 속도 제어기와 초기 기동을 포함한 SRM 구동 컨트롤러를 설계하기 위해 사용되었다. 폐루프 시스템에 안정된 효과를 보이는 FLM을 Pl 제어기에 추가함으로써 부적절하게 설정된 PI 제어기의 이득값에 대해 강인한 제어성능을 보인다. 시뮬레이션 및 실험결과는 6/4극 SRM에 대해 제안된 제어 방식이 우수함을 보여준다.

• 대한두개안면성형외과학회지
• /
• 제16권2호
• /
• pp.80-83
• /
• 2015

We present reconstruction of a complicated scalp-dura defect using acellular human dermis and latissimus dorsi myocutaneous free flap. A 62-year-old female had previously undergone decompressive craniectomy for intracranial hemorrhage. The cranial bone flap was cryopreserved and restored to the original location subsequently, but necessitated removal for a methicillin-resistant Staphylococcal infection. However, the infectious nidus remained in a dermal substitute that was left over the cerebrum. Upon re-exploration, this material was removed, and frank pus was observed in the deep space just over the arachnoid layer. This was carefully irrigated, and the dural defect was closed with acellular dermal matrix in a watertight manner. The remaining scalp defect was covered using a free latissimus dorsi flap with anastomosis between the thoracodorsal and deep temporal arteries. The wound healed well without complications, and the scalp remained intact without any evidence of cerebrospinal fluid leak or continued infection.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.155-158
• /
• 2001

A 640Gb/s high-speed ATM switching system that is based on the technologies of advanced MCM, 0.25um CMOS and optical WDM interconnection is fabricated for future N-ISDN services. A 40 layer, 160mm$\times$114mm ceramic MCM realizes the basic ATM switch module with 80Gbps throughput. The basic unit ATM switch module with 80Gb/s throughput. The basic unit ATM switch MCM consists of in 8 chip advanced 0.25um CMOS VLSI and 32 chip I/O Bipolar VLSIs. The MCM employs an 40 layer, very thin layer ceramic MCM and a uniquely structured closed loop type liquid colling system is adopted to cope with the MCM's high-power dissipation of 230w. The MCM is Mounted on a 32cm$\times$50cm mother board. A three stage ATM switch is realized by optical WDM interconnection between the high-performance MCM.

• 한국해양학회지:바다
• /
• 제16권2호
• /
• pp.70-80
• /
• 2011

연안 하구는 인위적인 개발압력이 상존하며 자연적인 변화에도 민감하게 반응하는 지역이다. 따라서 보존과 지속 가능한 이용을 위해서는 하구 생태계의 구조와 기능에 대한 이해가 필요하며, 인위적 혹은 자연적 변화에 어떻게 반응할 것인지를 아는 것이 필요하다. 하구 생태계 변화의 방향과 현 상태를 용이하게 판단하기 위한 노력의 하나로서 비오톱(biotope)과 하구 타입 분류(typology)를 이용하여 "생태 구역"을 정의하였다. 하구댐의 유무, 염분특성, 식생유무에 따라 16개의 생태 구역을 정의하였고, 고성만에 위치한 고성천 인근 4개 하구(배둔, 구만, 마암, 고성) 생태계에서 지형, 하상경사, 퇴적물 특성, 염분 구조, 식생 면적 등을 통해 생태구역 구분을 시도하였다. 고성천 인근 하구에는 총 16개 생태구역 중 7개가 구분되었다. 자연형 하천인 구만천, 마암천, 배둔천의 상류에는 NFB(natural, fresh, bare)가 나타나고 있으며, 기수 지역에는 NLV(natural, low salinity, vegetated)가 그리고 갯벌에는 NHB(natural, high salinity, bare)가 나타났다. 폐쇄형인 고성천의 경우 담수지역에는 CFB(closed, fresh, bare), 이후 하구쪽으로 CFV(closed, fresh vegetated)가 나타났다. 갈대가 넓게 서식하는 하구댐 안쪽지역은 CLV(closed, low salinity, vegetated)가 나타나며, 거산방조제 바깥쪽은 CHB(closed, high salinity, bare)가 나타났다. 고성천의 CHB와 CLV 지역은 방조제가 하구 생태계에 미치는 영향을 잘 보여주고 있다. 염분이 비교적 높고, 수심이 갚은 수로나 갯벌이 존재하던 CHB 지역이 하구둑에 의해 고염분 지역과 단절되면서 염분이 감소하고, 조석의 영향이 줄어들면서 침수가 줄고, 결국 갈대가 서식하기에 적합한 환경으로 바뀌게 되며, CLV로 바뀐 것으로 여겨진다. 국내의 여러 하구에 나타나는 생태구역을 데이터베이스화하여 각 생태구역의 출현 분포를 파악하는 것이 필요하며, 이러한 자료는 인위적, 자연적 변화에 의한 하구 생태계 변동을 예측하고 관리/대응 방안을 마련하는데 이용될 것이다. 생태구역 변화는 생태구조와 가능의 변화를 가져오기 때문에 생태계 역할 및 가치의 변화를 수반하며, 생태 구역 변화를 야기하는 사업의 타당성을 판단하는 근거자료로 이용될 수 있다.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송∙미디어공학회 2017년도 추계학술대회
• /
• pp.139-141
• /
• 2017

화재는 다른 재난보다 확산 속도가 빠르기 때문에 신속하고 정확한 감지와 지속적인 감시가 요구된다. 최근, 신속하고 정확한 화재 감지를 위해, CCTV(Closed-Circuit TeleVision)으로 획득한 이미지를 기계학습(Machine Learning)을 이용해 화재 발생 여부를 감지하는 화재 감지 시스템이 주목받고 있다. 본 논문에서는 기계학습의 기술 중 정확도가 가장 높은 딥러닝(Deep Learning)기반의 CCTV 화재 감지 시스템을 제안한다. 본 논문의 시스템은 딥러닝 기술 적용뿐만이 아니라, CCTV 이미지 전처리 과정을 보완함으로써 딥러닝에서의 미지 데이터(unseen data)의 낮은 분류 정확도 문제인 과적합(overfitting)문제를 해결하였다. 본 논문의 시스템은 약 80,000 개의 CCTV 이미지 데이터를 학습하여, 90% 이상의 화재 이미지 분류 정확도의 성능을 보여주었다.

• 한국세라믹학회지
• /
• 제48권5호
• /
• pp.463-466
• /
• 2011

Wet foams formed through direct foaming were stabilized using various concentrations of amiphiphilic particles that could control pore size and porosity. These porous materials showed moderate strength upon compression with high porosity. Bubble size and wet foam stability were tailored by amphiphile concentration, particle concentration, contact angle, and pH of the suspension to obtain crack-free porous solid after sintering. Closed and open pores were obtained with sizes of 30~300 ${\mu}m$ and porosities of over 80%.