• Geotechnical Engineering
• /
• v.3 no.1
• /
• pp.7-24
• /
• 1987

Preloading surcharge method along with vertical drains was adopted to improve the performance of a very soft marine clay deposit. The onshore deposit, located in the Ulsan Bay area, consists of a 2 to 10m thick, very soft, highly compressible marine clay layer developed just below. the sea water level. The initial undrained shear strength of the clay layer was about 0.6 ton/m2. But, the deposit was designed after treatment to support some auxiliary facilities for a new ilo refinery plant, requiring bearing capacities of 3.6 to 5.4 ton/m2 and maximum allowablee settlement of less than 7.5cm. A total of 35, 000 wick drains Ivas installed to expedite drainage during preloading, and surcharge loads of up to 5m above the original ground level were applied in a step-by-step loading sequence to prevent ground failure by excess surcharge loads. An extensive program of field instrumentation was implemented to monitor the behavior of the clay deposit. Measurers!ends included settlements, excess pore pressure and its dissipation, ground farmer level fluctuation, and lateral movement of the so(t clay layer under the preloads. This paper describes the design concepts, construction methods and control procedures used for improvement of the clay layer. It also presents the ground behavior measured during construction, rind comparisons with theoretical predictions.

• Radiation Oncology Journal
• /
• v.20 no.1
• /
• pp.81-90
• /
• 2002

Purpose : To establish and verify the proper and the practical IMRT (Intensity--modulated radiation therapy) patient QA (Quality Assurance). Materials and Methods : An IMRT QA which consists of 3 steps and 16 items were designed and examined the validity of the program by applying to 9 patients, 12 IMRT cases of various sites. The three step OA program consists of RTP related QA, treatment information flow QA, and a treatment delivery QA procedure. The evaluation of organ constraints, the validity of the point dose, and the dose distribution are major issues in the RTP related QA procedure. The leaf sequence file generation, the evaluation of the MLC control file, the comparison of the dry run film, and the IMRT field simulate image were included in the treatment information flow procedure QA. The patient setup QA, the verification of the IMRT treatment fields to the patients, and the examination of the data in the Record & Verify system make up the treatment delivery QA procedure. Results : The point dose measurement results of 10 cases showed good agreement with the RTP calculation within $3\%$. One case showed more than a $3\%$ difference and the other case showed more than $5\%$, which was out side the tolerance level. We could not find any differences of more than 2 mm between the RTP leaf sequence and the dry run film. Film dosimetry and the dose distribution from the phantom plan showed the same tendency, but quantitative analysis was not possible because of the film dosimetry nature. No error had been found from the MLC control file and one mis-registration case was found before treatment. Conclusion : This study shows the usefulness and the necessity of the IMRT patient QA program. The whole procedure of this program should be peformed, especially by institutions that have just started to accumulate experience. But, the program is too complex and time consuming. Therefore, we propose practical and essential QA items for institutions in which the IMRT is performed as a routine procedure.

• The Journal of Korean Association of Computer Education
• /
• v.7 no.1
• /
• pp.107-118
• /
• 2004

This study aims to design and implement individual complete learning system based on IPI(Individually Prescribed Instruction) model. Most of current web based learning systems do not consider individual students' ability and just follow the sequence of instructing contents $\rightarrow$ providing problems $\rightarrow$ presenting the result of evaluating. However, this system focuses on individual ability prior to studying subjects. In individual complete learning system, it is acknowledged that a period and a pace to complete each task will differ from students to students, therefore until they complete the whole unit, they are not allowed to move onto the next unit. After completing each unit, there will be a process of evaluating students' performance. It is necessary to show the correct completion of 80% of the evaluation to move onto next step; for those who are evaluated as inadequate to move on, an individual supplementary instruction will be provided. Therefore, this study intends to supplement the deficit of prior learning and provide feedback dependent on individual's learning ability so that the goal of Individual Whole Complete Learning could be accomplished.

• Restorative Dentistry and Endodontics
• /
• v.34 no.4
• /
• pp.333-339
• /
• 2009

This study was done to determine if there is any difference in microleakage between experimental composite resins, in which various proportions of three component photoinitiators (Camphoroquinone, OPPI, Amine) were included. Four kinds of experimental composite resin were made by mixing 3.2% silanated barium glass (78 wt.%, average size; 1 ${\mu}m$) with each monomer system including variously proportioned photoinitiator systems used for photoinitiating BisGMA/BisEMA/TEGDMA monomer blend (37.5:37.5:25 wt.%). The weight percentage of each component were as follows (in sequence Camphoroquinone, OPPI, Amine): Group A - 0.5%, 0%, 1% / Group B - 2%, 0.2%, 2% / Group C - 0.2%, 1%, 0.2% / Group D - 1%, 1%, 2%. Each composite resin was used as a filling material for round class V cavities (diameter: 2/3 of mesiodistal width; depth: 1.5 mm) made on extracted human premolars and they were polymerized using curing light unit (XL 2500, 3M ESPE) for 40 s with an intensity of 600 mW/$cm^2$. Teeth were thermocycled fivehundred times between $50^{\circ}C$and $550^{\circ}C$for 30s at each temperature. Electrical conductivity (${\mu}A$) was recorded two times (just after thermocycling and after three-month storage in saline solution) by electrochemical method. Microleakage scores of each group according to evaluation time were as follows [Group: at first record / at second record; unit (${\mu}A$)]: A: 3.80 (0.69) / 13.22 (4.48), B: 3.42 (1.33) / 18.84 (5.53), C: 4.18 (2.55) / 28.08 (7.75), D: 4.12 (1.86) / 7.41 (3.41). Just after thermocycling, there was no difference in microleakage between groups, however, group C showed the largest score after three-month storage. Although there seems to be no difference in microleakage between groups just after thermocycling, composite resin with highly concentrated initiation system or classical design (Camphoroquinone and Amine system) would be more desirable for minimizing microleakage after three-month storage.

• Journal of Internet Computing and Services
• /
• v.5 no.5
• /
• pp.1-15
• /
• 2004

In this paper, we explain the design and implementation of GWB(Gene WorkBench), which is a web-based, integrated system for efficiently managing and analyzing genomic sequences, Most existing software systems handling genomic sequences rarely provide both managing facilities and analyzing facilities. The analysis programs also tend to be unit programs that include just single or some part of the required functions. Moreover, these programs are widely distributed over Internet and require different execution environments. As lots of manual and conversion works are required for using these programs together, many life science researchers suffer great inconveniences. in order to overcome the problems of existing systems and provide a more convenient one for helping genomic researches in effective ways, this paper integrates both managing facilities and analyzing facilities into a single system called GWB. Most important issues regarding the design of GWB are how to integrate many different analysis programs into a single software system, and how to provide data or databases of different formats required to run these programs. In order to address these issues, GWB integrates different analysis programs byusing common input/output interfaces called wrappers, suggests a common format of genomic sequence data, organizes local databases consisting of a relational database and an indexed sequential file, and provides facilities for converting data among several well-known different formats and exporting local databases into XML files.

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 2002.10a
• /
• pp.18-25
• /
• 2002

The pikromycin biosynthetic system in Streptomyces venezuleae is unique for its ability to produce two groups of antibiotics that include the 12-membered ring macrolides methymycin and neomethymycin, and the 14-membered ring macrolides narbomycin and pikromycin. The metabolic pathway also contains two post polyketide-modification enzymes, a glycosyltransferase and P450 hydroxylase that have unusually broad substrate specificities. In order to explore further the substrate flexibility of these enzymes a series of hybrid polyketide synthases were constructed and their metabolic products characterized. The plasmid-based replacement of the multifunctional protein subunits of the pikromycin PKS in S. venezuelae by the corresponding subunits from heterologous modular PKSs resulted in recombinant strains that produce both 12- and 14-membered ring macrolactones with predicted structural alterations. In all cases, novel macrolactones were produced and further modified by the DesVII glycosyltransferase and PikC hydroxylase leading to biologically active macrolide structures. These results demonstrate that hybrid PKSs in S. venezuelae can produce a multiplicity of new macrolactones that are modified further by the highly flexible DesVII glycosyltransferase and PikC hydroxylase tailoring enzymes. This work demonstrates the unique capacity of the S. venezuelae pikromycin pathway to expand the toolbox of combinatorial biosynthesis and to accelerate the creation of novel biologically active natural products. The polyketide backbone of rifamycin B is assembled through successive condensation and ${\beta}$-carbonyl processing of the extender units by the modular rifamycin PKS. The eighth module, in the RifD protein, contains nonfunctional DH domain and functional KR domain, which specify the reduction of the ${\beta}$-carbonyl group resulting in the C-21 bydroxyl of rifamycin B. A four amino acid substitution and one amino acid deletion were introduced in the putative NADPH binding motif in the proposed KR domain encoded by rifD. This strategy of mutation was based on the amino acid sequences of the corresponding motif of the KR domain of module 3 in the RifA protein, which is believed dysfunctional, so as to introduce a minimum alteration and retain the reading frame intact, yet ensure loss of function. The resulting strain produces linear polyketides, from tetraketide to octaketide, which are also produced by a rifD disrupted mutant as a consequence of premature termination of polyketide assembly. Much of the structural diversity within the polyketide superfamily of natural products is due to the ability of PKSs to vary the reduction level of every other alternate carbon atom in the backbone. Thus, the ability to introduce heterologous reductive segments such as ketoreductase (KR), dehydratase (DH), and enoylreductase (ER) into modules that naturally lack these activities would increase the power of the combinatorial biosynthetic toolbox. The dehydratase domain of module 7 of the rifamycin PKS, which is predicted to be nonfunctional in view of the sequence of the apparent active site, was replaced with its functional homolog from module 7 of rapamycin-producing polyketide synthase. The resulting mutant strain behaved like a rifC disrupted mutant, i.e., it accumulated the heptaketide intermediate and its precursors. This result points out a major difficulty we have encountered with all the Amycolatopsis mediterranei strain containing hybrid polyketide synthases: all the engineered strains prepared so far accumulate a plethora of products derived from the polyketide chain assembly intermediates as major products instead of just analogs of rifamycin B or its ansamycin precursors.

• Bulletin of the Korean Mathematical Society
• /
• v.20 no.1
• /
• pp.45-49
• /
• 1983

If R is ring and M is a right (or left) R-module, then M is called a faithful R-module if, for some a in R, x.a=0 for all x.mem.M then a=0. In [4], R.E. Johnson defines that M is a prime module if every non-zero submodule of M is faithful. Let us define that M is of prime type provided that M is faithful if and only if every non-zero submodule is faithful. We call a right (left) ideal I of R is of prime type if R/I is of prime type as a R-module. This is equivalent to the condition that if xRy.subeq.I then either x.mem.I ro y.mem.I (see [5:3:1]). It is easy to see that in case R is a commutative ring then a right or left ideal of a prime type is just a prime ideal. We have defined in [5], that a chain of right ideals of prime type in a ring R is a finite strictly increasing sequence I$_{0}$.contnd.I$_{1}$.contnd....contnd.I$_{n}$; the length of the chain is n. By the right dimension of a ring R, which is denoted by dim, R, we mean the supremum of the length of all chains of right ideals of prime type in R. It is an integer .geq.0 or .inf.. The left dimension of R, which is denoted by dim$_{l}$ R is similarly defined. It was shown in [5], that dim$_{r}$R=0 if and only if dim$_{l}$ R=0 if and only if R modulo the prime radical is a strongly regular ring. By "a strongly regular ring", we mean that for every a in R there is x in R such that axa=a=a$^{2}$x. It was also shown that R is a simple ring if and only if every right ideal is of prime type if and only if every left ideal is of prime type. In case, R is a (right or left) primitive ring then dim$_{r}$R=n if and only if dim$_{l}$ R=n if and only if R.iden.D$_{n+1}$ , n+1 by n+1 matrix ring on a division ring D. in this paper, we establish the following results: (1) If R is prime ring and dim$_{r}$R=n then either R is a righe Ore domain such that every non-zero right ideal of a prime type contains a non-zero minimal prime ideal or the classical ring of ritght quotients is isomorphic to m*m matrix ring over a division ring where m.leq.n+1. (b) If R is prime ring and dim$_{r}$R=n then dim$_{l}$ R=n if dim$_{l}$ R=n if dim$_{l}$ R<.inf. (c) Let R be a principal right and left ideal domain. If dim$_{r}$R=1 then R is an unique factorization domain.TEX>R=1 then R is an unique factorization domain.

• Cartoon and Animation Studies
• /
• s.23
• /
• pp.1-17
• /
• 2011

The paper analyzed the metaphoric expressions appeared in whose cinematic quality has been subjectively recognized on the global stage by winning the Oscar for Best Animated Short Film. Many contents and visual effects of the film were expressed with metaphor. Story and sequence were analyzed through the language system-based 'Conceptual Metaphor Analysis Framework'. In addition, characters have been analyzed through the 'Visual Metaphor Analysis Framework'. The framework is to analyze visual dimensions which are derived when concepts are structuredin animation. This paper has attempted to investigate and reveal patterns how animation self-organizes or how animation self-realizes through linguistic objectives. That is, it is to reveal how animation communicates with the audience from the metaphoric perspective among many conventional ones. In an animated film, metaphor is a fundamental means to connect fragmented images, produce a holistic view and therefore induce creative communication with the audience. The essential motive of metaphor which is expressed in various styles in is modern people's feeling of loss and sense of missing something. Train, bottle top, food, lost-and-found center, in-between space and lost items have significance across the movie. According to an analysis, metaphor offers simplicity and freshness as an aesthetic function. In addition, the metaphor expresses lengthy contents and various meanings implicitly, delivering an economic function. With a creative function, metaphor is a tool to generate new meanings. In other words, an animated film is a medium to inspire and move the general public as a means of communication and thinking, not just an entertainment for young generations. After all, metaphoric expressions have been used to deliver diverse and deep meanings in animated films.

• Korean Journal of Microbiology
• /
• v.37 no.4
• /
• pp.265-272
• /
• 2001

The diversity of acid-tolerant epiphytic bacterial communities on deciduous oak tree (Quercus dentate Thunb.) leaves was examined both in the natural forest area with a clean air and in the industrial estate to assess effects of acidic depositions to the phyllosphere using 16S rDNA sequence data. A total of 444 acid-tolerant epiphytic bacterial clones were obtained, resulting in 17 phylotypes by performing a analysis of restriction fragment length polymorphism (RFLP) for PCR-amplified 16S rDNA products. A very low diversity of dominating acid tolerant bacterial communities in both areas was found, just 2 subphyla groups, $\gamma$-Proteobacteria and low-G+C gram-positive bacteria. As tree leaves grow older, diversities of acid-tolerant bacteria on them significantly increased. The community structure of acid-tolerant epiphytic bacteria consisted of Pseudomonas and Enterobacteriaceae groups in the $\gamma$-Proteobacteria subphylum, and Streptococcaceae and Staphylococcus groups in the low-G+C gram-positive bacteria subphylum. The direct influence of acidic depositions on bacterial phylogenetic composition could not be detected especially when higher taxonomic levels such as subphylum, but at narrower or finer levels it could be observed by a detection of Xanthomonadales group belonged to the $\gamma$-Proteobacteria only in the industrial area and of Acetobacteraceae group belonged to the $\alpha$-Proteobacteria. There remains that these specific acid-tolerant epiphytic bacterial groups could be used as indicators for assessing effects of acidic depositions on the phyllosphere.

• Journal of Drive and Control
• /
• v.20 no.4
• /
• pp.115-122
• /
• 2023

This study utilized a discrete element method (DEM) simulation, as one of the virtual field trials, to predict the impact of tillage depth on the rotary blade shaft during rotavator tilling. The virtual field for the simulation was generated according to soil properties observed in an actual field. Following the generation of particles for the virtual field, a sequence of calibration steps followed to align the mechanical properties more closely with those of real soil. Calibration was conducted with a focus on bulk density and shear torque, resulting in calibration errors of just 0.02% for bulk density and 0.52% for shear torque. The prediction of the load on a rotary tiller's blade shaft involved a three-pronged approach, considering shaft torque, draft force, and vertical force. In terms of shaft torque, the values exhibited significant increases of 42.34% and 36.91% for every 5-centimeter increment in tillage depth. Similarly, the vertical force saw substantial growth by 40.41% and 36.08% for every 5-centimeter increment. In contrast, the variation in draft force based on tillage depth was comparatively lower at 18.49% and 0.96%, indicating that the effect of tillage depth on draft force was less pronounced than its impact on shaft torque and vertical force. From a perspective of agricultural machinery research, this study provides valuable insights into the DEM soil modeling process, accounting for changes in soil properties with varying tillage depths. These findings are expected to be instrumental in future agricultural machinery design studies.