• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.463-469
• /
• 2004

In order to improve the instability of journal bearings, the leaf spring dampers (LSD) are introduced. The effects of LSD on the stability of journal bearings are investigated theoretically The stability of the journal bearing with LSD are compared with the results of the journal bearing without LSD. And the effects of the asymmetry of the stiffness of the leaf spring damper on the stability of rotors are also investigated.

• Tribology and Lubricants
• /
• 제5권1호
• /
• pp.69-75
• /
• 1989

The mobility method of dynamically loaded journal bearings was applied to optimize the lubrication of the main journal bearing of the crank press. The effects of oil viscosity, temperature bearing clearance, length, the existence of the circumferential groove, peak press force, and crank rpm were examined. From the results of the minimum film thickness and the maximum film pressure, some of the factors could be optimized, and the degrees of the beneficial and detrimental effects of the others could be estimated.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.342-349
• /
• 2006

In this study, a dynamic behavior of rotor-bearing system used in CNG compressor has been investigated using the combined methodologies of finite elements and transfer matrices. The finite element is formulated including the field element for a shaft section and the point element for roller bearings. The Houbolt method is used to consider the time march for the integration of the system equations. The transient whirl response of rotating shaft supported on roller bearings is obtained, considering compression forces and unbalance forces at eccentric crank-pin part. And, the steady state displacements of the rotor are compared with a variation in stiffness coefficient of roller bearings. Results show that the loci of crankshaft considering unbalance forces and external compression forces are more severe in whirl motion than with only unbalance forces.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.283-287
• /
• 2007

Permanent-magnet (PM) passive bearings use the repulsive forces between the rotor and the stator magnets for the bearing function. It is desirable that the stiffness of the bearing is maximized with the given volume of the magnet. The stiffness is affected by the magnet strength, the number of layers, and the magnetization patterns. Previously, finite-element method (FEM) has been used to maximize the stiffness of the bearing. In this paper, we used the equivalent current sheet method to calculate the stiffness. The validity of this approach is checked against FEM results. The optimized bearing is applied to a micro flywheel energy storage system.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권6호
• /
• pp.286-290
• /
• 2003

The high temperature superconducting bulk can be used as the bearing of induction motors. This paper presents the fabrication and test results of an induction motor with superconducting bearings using HTS bulks. The bearing had eight hexahedron type YBCO bulks. Height, width and thickness of the HTS bulk were 30mm, 30mm and 10mm, respectively. Single phase induction motor was used to drive the shaft made of aluminum and the rotor of a conventional induction motor. To estimate the performance of the HTS bulk magnetic bearing, no load test, load test and Impact test were carried out. Load tests were performed by using air resistance caused by the shaft-mounted thin cylinder with buckets. Impact tests by axial direction and vertical direction impact showed that the vibration of the shaft gradually decayed. The induction motor with HTS bulk magnetic bearing rotated silently and smoothly throughout the tests. According to the test results, conventional bearings can be replaced with superconducting magnetic bearings made of HTS bulks.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.116-121
• /
• 2010

For over a decade, research and development on submerged hardware in continuous galvanizing pots has been carried out at Teck's Product Technology Centre. The outcome of numerous laboratory tests and field trials has demonstrated that dissimilar materials with comparable surface hardness are most suitable for the manufacture of roll bearings. Wear debris can be easily retained in bearings made of the same material, thereby negatively affecting bearing performance and service life. Bearings made of the same materials are also vulnerable to catastrophic failures. The dissolution of iron from the coated strip creates an iron-rich zone associated with a high concentration gradient in the vicinity of the sink roll. Consequently, the sink roll becomes a preferential site for dross pick-up. In operations involving extremely high temperatures, such as in Galvalume production, the material selection for pot hardware is immaterial to the final corrosion product of the hardware and the pick-up on the hardware.

• 전기학회논문지
• /
• 제59권12호
• /
• pp.2319-2323
• /
• 2010

The existing contact-type bearings using rolling or sliding require continuous maintenance due to abrasion caused by friction and are not suitable for high-speed rotation and slimming. A magnetic bearing without contact can overcome such problems but the performance depends on the allocation of magnets and the structure of bearings. This paper proposes a method designing parameters of a passive magnetic bearing to improve levitation force. The proposed method employs Halbach array as the allocation of magnets, uses particle swam optimization to determine the structure of bearings. The numerical experiment shows that the levitation force is improved by the proposed method compared with the existing one using finite element analysis.

• Structural Engineering and Mechanics
• /
• 제49권4호
• /
• pp.463-477
• /
• 2014

In this paper, seismic performance of Kozyatagi Bridge is evaluated by employing nonlinear elasto-plastic dynamic analysis and the deformation-based performance. The time-history records of the 1999 Izmit, 1971 San Fernando and 1989 Loma Prieta earthquakes are modified by adopting a probability of exceedance of 2% in 50 years corresponding to the return period of 2475 years. The analysis is carried out for three different bearing cases which are movable bearings, restrained bearings, and movable bearings with viscous fluid dampers in the radial direction. The analysis results show that the bridge can be retrofitted with viscous fluid dampers. In this case the reinforced concrete piers need not be strengthened by any jacketing techniques in order to preserve the original architectural appearance of the bridge. The retrofitting design of the bridge with viscous fluid dampers is also presented in detail.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1787-1798
• /
• 1995

Monitoring and diagnosis of the operating machine mean evaluating the condition of a machine such as the detection of the defects and the prediction of the time to failure in the machine elements, while it is running. In this study, a technique of automatic diagnosis using probability concept is studied and the analyses of the pattern comparison are introduced. An expert system, which is able to analyze the automatic identification of the multiple defects in the ball bearings, is also developed. Finally, to confirm the effectiveness of the programmed algorithms, some tests were made with specimens of the ball bearings involving the multiple defects. The proposed system reasonably predicts the defects.

• 한국소음진동공학회논문집
• /
• 제17권11호
• /
• pp.1102-1111
• /
• 2007

The theory for a fault-tolerant control of homopolar magnetic bearings is developed. New coil winding law is utilized such that control fluxes are isolated for an 8-pole homopolar magnetic bearing. Decoupling chokes are not required for the fault tolerant magnetic bearing since C-core fluxes are isolated. If some of the coils or power amplifiers suddenly fail, the remaining coil currents change via a distribution matrix such that the same magnetic forces are maintained before and after failure. Lagrange multiplier optimization with equality constraints is utilized to calculate the optimal distribution matrix that maximizes the load capacity of the failed bearing. Some numerical examples of distribution matrices are provided to illustrate the theory. Simulations show that very much the same dynamic responses (orbits or displacements) are maintained throughout failure events while currents and fluxes change significantly.