• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.55-62
• /
• 2014

The use of light-weight Al alloys in the automotive industry is increasing to meet requirements for fuel efficiency and emission reduction. Joining Al alloy to the conventional steel sheet is also very important issue with the increased use of Al alloy, and several joining processes have been introduced to enhance joining strength between dissimilar metals. This paper deals with a galvanic corrosion in the dissimilar metal joining. Salt spray tests up to 2000 hours were conducted on a self-piercing rivet, spot welded, adhesive bonded and weld-bonded joints, and cross-sections and tensile shear strength according the salt spray duration were analyzed at every 500-hour. Self-piercing rivet joint had relative low initial strength but the joint strength did not change regardless of the salt spray duration. The strength of other joints (spot welded, adhesive bonded and weld-bonded joints) decreased with the increase of salt spray duration and the corrosion behaviour of each joint was discussed.

• Biomedical Science Letters
• /
• v.29 no.4
• /
• pp.220-230
• /
• 2023

Identification of the pathogens causing infection is important in terms of patient's health management and infection control. Synovial fluids could be used as clinical samples to detect causative pathogens of prosthetic joint infections (PJIs) using molecular diagnostic assays, therefore, normalization and validation of clinical samples are necessary. Microbial culture is considered the gold standard for all infections, including PJIs. Recently, molecular diagnostic methods have been developed to overcome the limitation of microbial culture. Therefore, guideline for validating clinical samples to provide reliable results of molecular diagnostic assays for infectious diseases is required in clinical field. The present study aimed to develop an accurate validating method of synovial fluid clinical samples using GAPDH gene as an internal control to perform the quantitative PCR TaqMan probe assay to detect pathogens causing PJIs.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.3
• /
• pp.690-696
• /
• 2013

This study, which is conducted on two groups of skilled people and unskilled people, is purposed to analyze joint angle of lower extremity during short track speed skating in order to find out efficient body position and propose ideal training method. Short Track Speed Skating has a wide range of research areas, but their findings indicate a promising area for further research. Targeting 8 people who are skilled in short track speed skating and 8 people who are not skilled in it, this study analyzes three dimensional images using super-high speed camera to compare differences between these two groups of people. In this study, 6 sections of body positions including right foot push-off, right foot recovery, right foot basic position, left foot push-off, left foot recovery, and left foot basic position were analyzed using 8 super-high speed cameras of VICON. These body positions were analyzed in order to find out joint angles of the hip joint, the knee joint, and the ankle joint. In the section 4 of the inner and outer parts of the left hip angles showed significant difference, and most of the sections of knee joint angles also showed significant difference. In the section 1 and 2 of the plantar flexion, dorsiflexion of ankle joints showed significant difference(p<.001) It was found out that there were differences between groups of skilled people and unskilled people in terms of lower extremity's joint angles such as angles of the hip joint, the knee joint, and the ankle joint.

• Journal of Technologic Dentistry
• /
• v.35 no.3
• /
• pp.231-242
• /
• 2013

Purpose: The study is to discover the relationship between malocclusion, which is known to cause temporomandibular disorder, and temporomandibular disorder and is aimed at college students who have retained their natural teeth. Methods: The study was aimed at 500 college students at two colleges located in Gyeongsangbuk-do and Daegu metropolitan city and survey research was conducted in order to discover any relationship between malocclusion and temporomandibular disorder. After excluding copies with insincere answers or errors out of the 500 copies of the questionnaire, the study used a total of 435 copies (87%) for research and analysis. Results: Females showed a prevalence of temporomandibular joint clicking and temporomandibular joint pain, and students who had crowding showed a high prevalence of temporomandibular joint pain, temporomandibular joint clicking, and trismus. Students whose occlusal condition was not good demonstrated a high prevalence of temporomandibular joint pain, temporomandibular joint clicking, and trismus. Students who had maxillary protrusion showed a prevalence of temporomandibular joint clicking and trimus, whereas students who had mandibular protrusion showed a high prevalence of temporomandibular joint clicking. Conclusion: Students whose dental condition was crowding and students whose occlusal condition was not good exhibited a high prevalence of three types of symptoms of temporomandibular disorder. Meanwhile student who had maxillary protrusion showed a high prevalence of temporomandibular joint clicking and trismus, while students who had mandibular protrusion showed a prevalence of temporomandibular joint clicking.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.2
• /
• pp.126-132
• /
• 2014

PURPOSE. This study was conducted to evaluate the influence of the implant-abutment connection design and diameter on the screw joint stability. MATERIALS AND METHODS. Regular and wide-diameter implant systems with three different joint connection designs: an external butt joint, a one-stage internal cone, and a two-stage internal cone were divided into seven groups (n=5, in each group). The initial removal torque values of the abutment screw were measured with a digital torque gauge. The postload removal torque values were measured after 100,000 cycles of a 150 N and a 10 Hz cyclic load had been applied. Subsequently, the rates of the initial and postload removal torque losses were calculated to evaluate the effect of the joint connection design and diameter on the screw joint stability. Each group was compared using Kruskal-Wallis test and Mann-Whitney U test as post-hoc test (${\alpha}$=0.05). RESULTS. The postload removal torque value was high in the following order with regard to magnitude: two-stage internal cone, one-stage internal cone, and external butt joint systems. In the regular-diameter group, the external butt joint and one-stage internal cone systems showed lower postload removal torque loss rates than the two-stage internal cone system. In the wide-diameter group, the external butt joint system showed a lower loss rate than the one-stage internal cone and two-stage internal cone systems. In the two-stage internal cone system, the wide-diameter group showed a significantly lower loss rate than the regular-diameter group (P<.05). CONCLUSION. The results of this study showed that the external butt joint was more advantageous than the internal cone in terms of the postload removal torque loss. For the difference in the implant diameter, a wide diameter was more advantageous in terms of the torque loss rate.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.101.1-101.1
• /
• 2007

• ETRI Journal
• /
• v.34 no.5
• /
• pp.783-786
• /
• 2012

This letter proposes a more advanced joint maximum a posteriori (MAP) adaptation using a prior model based on a probabilistic scheme utilizing the bilinear transformation (BIT) concept. The proposed method not only has scalable parameters but is also based on a single prior distribution without the heuristic parameters of the previous joint BIT-MAP method. Experiment results, irrespective of the amount of adaptation data, show that the proposed method leads to a consistent improvement over the previous method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.499-502
• /
• 2003

The purpose of this study is to understand the sliding characteristics of the infilling-joint surface using the new devised shear test apparatus with changeable slope for the original infilling materials and the infilling materials experienced cyclic freezing-thawing processes. Three types of the mother rock classified as the igneous rock, the metamorphic rock and the sedimentary rock and the infilling materials were collected for laboratory test. The cohesion according to the slope change of the rock joint shows large variation within ${\pm}$5 degrees but the internal friction angle shows appears the linear decreasing tendency. It is confirmed that the affecting factor of slope change of rock joint at the behavior of rock mass is larger than that of the infilling thickness. Test results show that the cohesion and the internal friction angle in 100 times of cyclic freezing-thawing processes are decreased about 50 percent compared with original one. A further study using various infillings materials would lead to a better understanding of the failure mechanism of rock mass by slope change of rock joint.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.967-974
• /
• 2013

Recently the authors had proposed the z-pinning patch concept to simply manufacture z-pinned composite structures at industrial production site and manufactured composite single-lap shear joint specimens using the concept. Through static tensile test on the specimens they had obtained 54~68% improvement of the joint strength. As a sequential study of it, in this study, fatigue test has performed to measure an improvement of joint strength under cyclic loading. The z-pin's material is stainless steel and its surface was specially machined into zagged shapes and chemically corroded to increase the connection force with composite materials. Approximately 98~125% improvement of the joint strength under cyclic loading was obtained.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.357-373
• /
• 2022

The high-temperature gas-cooled reactor pebble-bed module project is the first commercial Generation-IV NPP(Nuclear Power Plant) in China. A new joint is used for the vertical support of RPV(Reactor Pressure Vessel). The steel corbel is integrally embedded into the reactor-cabin wall through eight asymmetrically arranged pre-stressed high-strength bolts, achieving the different path transmission of shear force and moment. The vertical monotonic loading test of two specimens is conducted. The results show that the failure mode of the joint is bolt fracture. There is no prominent yield stage in the whole loading process. The stress of bolts is linearly distributed along the height of corbel at initial loading. As the load increases, the height of neutral axis of bolts gradually decreases. The upper and lower edges of the wall opening contact the corbel plate to restrict the rotation of the corbel. During the loading, the pre-stress of some bolts decreases. The increase of the pre-stress strength ratio of bolts has no noticeable effect on the structure stiffness, but it reduces the ultimate bearing capacity of the joint. A simplified calculation model for the elastic stage of the joint is established, and the estimation results are in good agreement with the experimental results.