• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.101-112
• /
• 1994

The measurement of residual stress distribution of $Si_3N_4/SUS304$ joint was performed on 23 specimens with the same joint condition using PSPC type X-ray stress measurement system and the two-dimensional elastoplastic analysis using finite element method was also attempted. As results, residual stress distribution near the interface on the ceramic side of the joint was revealed quantitatively. Residual stress on the ceramic side of the joint was turned out to be tensional near the interface, maximum along the edge, varying in accordance with the condition of the joint and variance to be most conspicuous for the residual stress normal to the interface characterized by the stress singularities. In the vicinity of the interface, the high stress concentration occurs and residual stress distributes three-dimensionally. Therefore, the measured stress distribution differed remarkably from the result of the two-dimensional finite-element analysis. Especially at the center of the specimen near the interface, the residual stress, $\sigma_{x}$ obtained from the finite element analysis was compressive, whereas measurement using X-ray yielded tensile $\sigma_{x}$. Here we discuss two dimensional superposition model the discrepancy between the results from the two dimensional finite element analysis and X-ray measurement.

• Journal of Welding and Joining
• /
• 제19권2호
• /
• pp.215-220
• /
• 2001

In the T-joint welding, the complete penetration joint which is obtained by groove welding with edge preparation is generally required thor the safety and reliability of structures but this way have the some defects such as increase of working time, consumed welding electrode quantity and large welding deformation. If there is no probrem, in the strength, T-joint welding without edge preparation will be profitably understood in the economical and welding deformation side. In this paper, we performed the finite element analysis to understand the characteristics of welding residual stresses on two models, complete penetration joint have the edge preparation and incomplete penetration joint without edge preparation, respectively. Especially, we observed the relation between welding residual stress distributed on the notch of gap in the root and external force in the incomplete penetration joint without edge preparation.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.216-219
• /
• 2000

The adhesive bonded single-lap joint is due to its intrinsic load eccentricity problem, severe peel stresses concentration occur at both end of the joint. In this paper, new lap-joint is designed to avoid the singular peel stress, and to compare the stresses of the middle adhesive layer between the single-lap joint and the wavy-lap joint. Two adherend lay-up, i.e., [90/0/90/0]$_{2s}$ and [0/90/0/90]$_{2s}$ were consider in the study.

• 터널과지하공간
• /
• 제28권4호
• /
• pp.343-357
• /
• 2018

절리군 대표방향성에만 의존하는 기존의 평사투영 사면해석의 불확실성을 극복하고 해석결과의 신뢰성을 증진시키기 위하여 확률통계학적으로 도출된 절리극점들의 dense point 및 절리군 대표방향성과 암반구조 분석결과를 종합적으로 고려하여 사면거동양상을 분석하는 알고리즘을 고안하였다. 이를 위하여 절리극점들의 분포양상에 의거하여 절리확산지수를 산정하는 기법을 고안하였으며, 콘각에 따라 상이하게 도출되는 절리확산지수 및 절리군 수효와 방향성을 종합적으로 고려하여 사면해석에 사용될 대표방향성을 추출하였다. 이들 대표방향성을 평사투영분석에 활용하여 신뢰성이 증진된 사면해석을 수행할 수 있었다. 또한 평면파괴가 우려되는 사면에 대해 한계평형이론에 의거하여 민감도 해석을 수행하고, 사면 안정성에 대한 절리강도 및 외부하중 변화의 영향을 심도 있게 분석하였다.

• 콘크리트학회논문집
• /
• 제24권5호
• /
• pp.517-524
• /
• 2012

이 논문에서는 푸쉬오버해석을 통해 보-기둥 접합부 비탄성 전단거동과 고차모드를 고려한 횡하중 수직분포 형태가 구조물 거동에 미치는 영향을 알아보기 위해 지반조건 $S_B$ 내진설계범주 C에 대해서 5층 철근콘크리트 보통모멘트골조를 KBC2009에 맞게 구조설계 하였다. 보 및 기둥 부재의 휨모멘트-곡률 관계는 섬유모델(fiber model)로 확인하였으며 보-기둥 접합부 모멘트-회전각 관계는 simple and unified joint shear behavior model과 보-기둥 접합부 모멘트 평형관계를 이용하여 확인하였다. 푸쉬오버해석 결과 보-기둥 접합부를 강체로 고려하는 경우 구조물의 강성도 및 강도가 과대평가 되었으나 반응수정계수는 접합부 비탄성거동과 관계없이 KBC2009 보통모멘트골조 계수를 만족하여 구조 설계 과정에서 보-기둥 접합부의 비탄성 전단거동을 고려하지 않아도 문제가 없을 것으로 판단된다.

• 한국지반공학회논문집
• /
• 제15권5호
• /
• pp.229-240
• /
• 1999

본 논문에서는 유한차분법, 채널망 해석법 및 절리망 해석법 등 다양한 해석기법을 이용하여 개별 암석절리 및 절리암반에서의 지하수 유동과 주입재의 유동거동을 연구하였다. 유동거동은 두개의 상이한 관찰규모, 즉 변화하는 간극분포를 가진 실험실 규모의 거친 절리면과 3개의 절리군에 속한 단절된 절리들을 포함하고 있는 현장 규모의 절리암반에 대해 수행되었다. 단일절리에서의 유동해석결과 물과 주입재 모두 간극분포에 의존하는 채널흐름의 특성을 확인할 수 있었다. 유한차분법과 기존의 이론해에 의한 유량 계산결과를 비교 분석하였다. 절리암반의 경우 절리의 수와 굴착된 원형공동의 직경을 증가시키면서 공동내부로의 지하수 유입량을 분석하였다. 이 분석에는 절리망 해석법과 Goodman의 이론해를 사용하여 결과를 비교하였다. 또한 절리망 해석법의 경계효과, 절리망의 비균질성이 지하수 유동에 미치는 영향 등을 논의하였다.

• 산업기술연구
• /
• 제21권B호
• /
• pp.325-330
• /
• 2001

In this research, the early-age movements of joint at JPCP(Jointed Plain Concrete Pavement) were measured by field tests. The field tests were carried out for 5 days just after concrete placement, for 1 day after 52 and 72 days on Chung-Ang Expressway construction site in Dan-yang on the 28th and 29th of May 2001. The joint movements were measured by demec gauge and clip gauge. The results of regression analysis for the data measured during early 5 days showed that the joints of No.4, No.5, No.6, No.10, No.13, and No.15 could be considered as a moving joint. From data analysis on july 20, the joints of No.2, No.9, and No.10 showed the significant correlations from the minus value of coefficient of regression. As a result of regression data on August 8, joint movements occurred at all joints. Joint freezing and closure could be judged from the regression analysis using joint opening and total temperature measured at field tests.

• 한국정밀공학회지
• /
• 제28권6호
• /
• pp.657-682
• /
• 2011

This paper presents the dynamic analysis on the joint torque of a finger for the tip pinch task. The dynamic model on finger movement was developed in order to predict the joint torques of an index finger, and the finger was assumed as a three-link planar manipulator. Analysis of the model revealed that the joint stiffness was one of the most important parameters affecting the joint torque. The stiffness of the finger joint was experimentally measured, and it was used in analyzing the finger joint torque required for performing the tip pinch task. The obtained joint torque for the tip pinch task will be used as the design requirements of the finger exoskeletal orthosis actuated by the polymer actuator whose allowable torque limit is relatively low compared to that of a mechanical actuator.

• 한국해양공학회지
• /
• 제13권2호통권32호
• /
• pp.51-57
• /
• 1999

In this study, one side fillet welded T-joint, used in box type girder and other welding structure, was investigated by stress analysis and bending fatigue test without edge preparation, with variation of joint shape. The purpose of this study is to give the welding condiltion and design standard on manufacturing one side fillet welded T-joint. As a result, the following conclusions were obtained. 1) In one side fillet welded T-joint, the larger the leg length and the penetration depth, the greater the bending fatigue strength because reduction of stress and strain on toe and root. The increase of the longitudinal leg length rather than vertical leg length contributed to the increase in bending fatigue strength. 2) In one side fillet welded T-joint without edge preparation, both general manual welding and general automatic welding were carried out with same condition. In this case, automatic welding showed deeper penetration and more increased longitudinal leg length than manual welding, so that automatic welding offers greater bending fatigue strength. 3) For one side fillet welded T-joint without edge preparation with automatic welding, the ratio(h/t) of the leg length(h) and the main plate thickness(t) in which toe crake can occur was 1.0 over.

• 한국군사과학기술학회지
• /
• 제13권3호
• /
• pp.421-430
• /
• 2010

This work describes a derivation process of JIC(Joint Integrating Concept) based JFC(Joint Functional Concept) analysis of an Aegis BMD(Ballistic Missile Defense). JIC is developed through JOC(Joint Operating Concept) and JFC based on capstone strategy and concept. Aegis BMD is a sea-based ballistic missile defense to detect ballistic missile threat, increase engagement battlespace and enable multiple engagement based on Aegis ships. Aegis BMD is a good case of JIC due to performing an Joint operations based on System of Systems under highly complicated NCW environment. This work analyses JFC using QFD(Quality Function Deployment) and UJTL(Universal Joint Task List). From this analysis the JIC of Aegis Korean BMD is derived using a CASE tool.