• Economic and Environmental Geology
• /
• v.28 no.3
• /
• pp.279-286
• /
• 1995

The amount of the high level radioactive wastes in Korea will be increased up to 14,297 MTU about 2010 year. Most of countries adopt the concept of deep burial repository in high level radioactive waste disposal. Because the high level radioactive wastes are very toxic in biosphere and to human, the data verifing its never return to the biosphere are requisite for the disposal. Presently, the evaluating techniques for the high level radioactive waste disposal are not fully developed. Therefore, in order to dispose the high level radioactive wastes in proper time the R & D of it is urged in our country. The R & D and/or the international joint research programme for the disposal of high level wastes have already been proceeded. In our country no plan for its disposal has been prepared. It is the time that the direction of the R & D is to be discused seriously. The R & D for the disposal of high level radioactive wastes in Korea is believed to be focused on developing the pecular techniques such as in situ characteristics of groundwater flowage, and change of properties of in situ rock mass at thermal effects.

• Laser Solutions
• /
• v.11 no.3
• /
• pp.21-24
• /
• 2008

Hybrid laser welding technology is a good process to reduce a thermal distortion and increase the productivity. However, it requires a high investment and a massive modification of the fabrication line such as a gantry system, milling machine for the edge preparation, high power laser system and weld machine. Therefore the development of an economical laser welding system is a crucial point to apply this system in shipbuilding yard. In this study, a portable hybrid laser welding carriage was developed for I-butt joint without edge milling. It is expected that the carriage type system could reduce investment cost.

• Journal of Welding and Joining
• /
• v.31 no.1
• /
• pp.21-25
• /
• 2013

Aluminum alloy, Al5083-O, is one of candidate materials for the LNG storage tank, because of its excellent weldability, cryogenic characteristics, and corrosion resistance. The good weldability of Al5083-O is very important in LNG storage tank manufacturing. In this study, high current metal inert gas(MIG) welding process was used to get one pass welding of thick plate aluminum alloy. Bead on plate(BOP) welding was performed to evaluate the effect of welding conditions on the height of bead and depth of penetration. The optimum welding conditions were derived to get one pass welding of the thickness of 14.5mm. The mechanical properties of the welded joint were evaluated. The cross-sectional macro test, tensile test, and bending test satisfied the class rule.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2023.11a
• /
• pp.279-280
• /
• 2023

최근 증가하고 있는 글로벌 이슈의 해결을 위해 국제 공동연구를 통한 글로벌 협력체계 강화에 대한 중요성이 커지고 있다. 이러한 흐름에 따라 한국 정부에서도 2024년 국제 공동연구 관련 R&D 예산 규모를 약 3배 가량 늘릴 것으로 발표하였다. 이에 본 연구에서는 2018년부터 2021년 동안의 정부 R&D 사업의 국제 공동연구 투자 현황을 살펴보고, 이를 향후 국제 공동연구에 대한 예산 계획을 수립하고, 국제 공동연구를 활성화하기 위한 전략 수립의 근거로 활용할 수 있을 것으로 기대한다.

• ETRI Journal
• /
• v.37 no.2
• /
• pp.380-386
• /
• 2015

Guaranteeing quality of service over a multihop wireless network is difficult because end-to-end (ETE) delay is accumulated at each hop in a multihop flow. Recently, research has been conducted on network coding (NC) schemes as an alternative mechanism to significantly increase the utilization of valuable resources in multihop wireless networks. This paper proposes a new section-based joint NC and scheduling scheme that can reduce ETE delay and enhance resource efficiency in a multihop wireless network. Next, this paper derives the average ETE delay of the proposed scheme and simulates a TDMA network where the proposed scheme is deployed. Finally, this paper compares the performance of the proposed scheme with that of the conventional sequential scheduling scheme. From the performance analysis and simulation results, the proposed scheme gives more delay-and energy-efficient slot assignments even if the NC operation is applied, resulting in a use of fewer network resources and a reduction in ETE delay.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.943-951
• /
• 2006

Multi-input-multi-output (MIMO) systems are considered to improve the capacity and reliability of next generation mobile communication. However, the multiple RF chains associated with multiple antennas are costly in terms of size, power and hardware. Antenna selection is a low-cost low-complexity alternative to capture many of the advantages of MIMO systems. We proposed new joint Tx/Rx antenna selection algorithm with low complexity. The proposed algorithm is a method selects $L_R{\times}L_T$ channel matrix out of $L_R{\times}L_T$ entire channel gain matrix where $L_R{\times}L_T$ matrix selects alternate Tx antenna with Rx antenna which have the largest channel gain to maximize Frobenius norm. The feature of this algorithm is very low complexity compare with Exhaustive search which have optimum capacity. In case of $4{\times}4$ antennas selection out of $8{\times}8$ antennas, the capacity decreases $0.5{\sim}2dB$ but the complexity also decreases about 1/10,000 than optimum exhaustive search.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.375-375
• /
• 1995

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2007.04a
• /
• pp.49-65
• /
• 2007

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.2
• /
• pp.103-110
• /
• 2019

• Journal of Welding and Joining
• /
• v.34 no.3
• /
• pp.6-11
• /
• 2016

Joining Al/Fe dissimilar metals is becoming a subject of special interest in the assembly of automotive parts as a trade-off between the weight lightening and the cost reduction. Although various studies have been introduced to join Al alloy with the steel sheet by fusion welding, weak joint strength and galvanic corrosion still remained as problems to be solved. As a solid state welding, friction stir welding has been preferred to fusion welding processes in the dissimilar metal joints. This study investigated friction stir spot welding (FSSW) of Al alloy to the thin steel sheet with a thickness of 0.65 mm. The conventional FSSW is a stationary spot welding process but new approach adopted an additional circumferential movement in company with high speed tool rotation. A full factorial experimental design was implemented, and the main and interaction effects of parameters were analysed on the failure load in the tensile shear test. The direction and radius of rotation were statistically significant parameters and these two parameters affected the joint width and the shape of the hook.