• Journal of the Korean Wood Science and Technology
• /
• 제39권6호
• /
• pp.481-489
• /
• 2011

본 연구에서는 소나무와 낙엽송 스킨팀버의 ACQ-2, CUAZ-2, CuHDO-1 가압처리 특성을 평가하기 위해 소나무 변재부와 낙엽송 심재부 시험편을 대상으로 처리용 목재의 함수율이 방부제 처리도에 미치는 영향과 방부제 유효성분인 구리의 처리목재 내 정착 특성을 조사하였다. 본 연구 결과에 의하면 소나무 변재부는 방부제 종류에 관계없이 함수율 30%부터 사용환경 범주 H3용 처리목재의 침윤도와 흡수량 기준을 모두 만족하였다. 완벽한 방부제 침투가 가능한 소나무 변재부에서 깊이에 따른 방부제 흡수량 경사를 조사한 결과, 방부제 종류에 따른 차이가 관찰되었다. CuHDO-1 처리 시험편에서 발생한 경사가 ACQ-2와 CUAZ-2 처리 시험편에서의 경사보다 심했는데, 특히 고함수율(25, 30%) 시험편에서 경사가 저함수율(15, 20%) 시험편에서보다 심함을 알 수 있었다. 그러나 난주입성인 낙엽송 심재부는 처리용 목재의 함수율 조건 및 방부제 종류에 관계없이 처리도 가 매우 불량하였다. 낙엽송 심재부의 처리도 개선을 위해 증기 전처리($121^{\circ}C$의 포화수증기 조건에서 12시간 처리)를 실시한 결과, 낙엽송 심재부의 침윤도와 흡수량 모두 사용환경 범주 H3용 처리목재 기준에 부합하게 처리도가 개선됨을 확인할 수 있었다. 소나무 변재부와 낙엽송 심재부 시험편에서 공히 방부제 유효성분인 구리의 정착이 비건조 양생에 비하여 건조 양생에서 빨리 진행되었다. 소나무 변재부는 양생 초기 3~6일, 낙엽송 심재부는 양생 1일 이내에 3주간 정착된 구리 양의 95% 이상이 정착되었다. 양생 3주 후 처리목재 내에 미정착 상태로 남아있는 구리의 양은 ACQ-2, CuHDO-1, CUAZ-2 순으로 많았는데, 이는 처리용 작업액에 존재하는 구리의 양과 비례하였다.

• 공업화학
• /
• 제31권3호
• /
• pp.277-283
• /
• 2020

본 연구는 건자재용 목재의 연기 유해성평가에 대하여 연기성능지수-II (SPI-II), 연기성장지수-II (SGI-II)를 중심으로 조사하였다. 시험편은 삼나무, 가문비나무, 나왕, 적송을 사용하였다. 연기 특성은 시험편 목재에 대하여 콘칼로리미터(ISO 5660-1) 장비를 이용하여 조사하였다. 연소반응 후 측정된 연기성능지수-II는 적송을 기준으로 1.31~2.15배 증가하였다. 연기성능지수-II에 의한 화재위험성은 가문비나무, 나왕, 삼나무, 적송의 순서로 증가하였다. 연기성장지수-II는 삼나무를 기준으로 1.18~2.55배 증가하였다. 연기성장지수-II에 의한 화재위험성은 삼나무, 가문비나무, 나왕, 적송의 순서로 높아졌다. CO 평균농도는 59~133 ppm이었으며 이 결과는 미국직업안전위생관리국(occupational safety and health administration, OSHA)의 허용기준(permissible exposure limits, PEL)인 50 ppm 보다 높게 나타났다. 결론적으로 적송과 같이 휘발성 유기물질을 다랑 함유한 목재는 연기성능지수-II가 낮고, 연기성장지수-II가 높으므로 화재로 인한 연기유해성이 높은 것으로 이해된다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권1호
• /
• pp.11-16
• /
• 1996

The purpose of this paper is to present a summary of assignment design values according to domestic softwood structural lumber grading rules. Allowable stresses for visually graded lumber were determined from basic data on small. clear specimens. The data corrected for variability such as natural defects and other factors. The procedure adopted by Japan was used for assigning allowable design values. Strength ratios in relation to each defect were taken from ASTM D 245-81. Korean pine(Pinus koraiensis S. et Z.), Korean red pine(Pinus densiflora S. et Z.), Japanese larch(Larix leptolepis Gordon) and Needle fir(Abies holophylla Max) were applied to this study. The calculated allowable stresses were same in Korean pine and Korean red pine. These values were highest in Japanese larch lowest in Needle fir. So, it is desirable for these species to be classified into different catagories Species Group. However, accurate comparison in design values on lumber grading rules among U.S., Japan and Korea was somewhat difficult. And full scale testing will be necessary for accurate determination of the correction factors to setting up design values.

• 한국산림과학회지
• /
• 제87권4호
• /
• pp.543-548
• /
• 1998

소나무와 해송으로부터 엽록체상의 두 유전자 psbD와 rbcL를 PCR에 의해 증폭한 후 제한효소 HaeIII를 사용해서 절단했다. 두 개의 종 특이적 엽록체 DNA 단편이 확인되었고, 이 두 개의 표지자를 이용하여 소나무(충북3호)와 해송(남난37호)의 인공교잡 가계로부터 엽록체 DNA의 부계 유전양식이 확인되었다. 인공교잡 가계에 있어서 엽록체 DNA의 부계 유전양식을 근거로 해송으로부터 소나무로의 이입교잡에 의해 생겨났다는 가설(현신규 등, 1967)이 지배적인 금강송 115개체로부터 이입교잡에 의해 유입되어진 흔적을 구명하기 위하여 해송 특이 엽록체 DNA의 존재 여부를 검색하였다. 분석에 사용된 금강송 전 개체에서 소나무에서 관찰된 엽록체 DNA(psbD와 rbeL)의 절편 분획 양상과 동일한 절편 분획 양상이 확인되었다. 본 실험의 결과로부터는, 금강송에는 해송으로부터 유입된 엽록체 게놈의 흔적을 찾아 볼 수 없었으며, 따라서 금강송을 소나무(♀)약 해송(♂)의 이입교잡종이이라고 간주할만한 확고한 증거를 제시할 수 없었다.

• Journal of Forest and Environmental Science
• /
• 제33권4호
• /
• pp.315-321
• /
• 2017

This study was carried out to estimate the parameters of stem taper functions, to figure out the best taper model by species, and to compare with previous studies by species, targeting on the stemmed tree samples collected from the Korean red pine (Pinus densiflora), Korean white pine (Pinus koraiensis), and Japanese larch (Larix kaempferi ) stands in Gangwon and North Gyeongsang provinces of South Korea. The seven widely used models were applied in this study, and Muhairwe 1999 model for Korean red pine and Korean white pine and Kozak 2002 model for Japanese larch were evaluated as the best model for each species according to the fit statistics and the predicted stem form comparison. In addition, the predicted diameter was suitably fitted when comparing the previous studies, and the values were more appropriate following stem taper according to neiloid, paraboloid, and cone parts by species. Consequently, the estimation of this study was considered to represent the stem taper well. When comparing stem taper of three species, the diameter was largest in Korean white pine. Overall, the taper models of this study are judged to be useful for estimating stem form and volume computation of Korean red pine, Korean white pine, and Japanese larch.

• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.34-42
• /
• 1998

Three hardwood (ash, alder and black locust) and three softwood (Japanese red pine, radiata pine and Western hemlock) specimens were dried in microwave(MlW) oven and their drying rates were obtained. Their specific permeabilities were also measured by using a modified liquid permeability measuring device. The correlation between the M/W drying rates and permeabilities of six species were statistically analyzed. It was revealed that within a species there is a logarithmic relationship between the M/W drying rates and average moisture contents and that among species there is a linear relationship between the M/W maximum drying rates and the average specific permeabilities. A exception was Western hemlock, which was of low permeability and of high drying rate. A Me-time equation, which showed a good agreement with the actual data, was derived. Thus using this equation the moisture contents of wood and the drying end points of M/W drying could be predicted. Infrared images of the thermal distribution in wood were illustrated.

• Journal of the Korean Wood Science and Technology
• /
• 제31권1호
• /
• pp.27-31
• /
• 2003

이 논문은 소나무와 일본잎갈나무의 변장 14.0 cm와 16.5 cm인 큰 정각재의 천연건조과정과 함수율분포에 관한 내용으로서 건조속도는 건조개시 첫 8주 동안 비교적 컸었으나, 그 이후부터 점차 감소하였다. 생재에서 규격함수율 18% 수준까지 건조시간은 소나무 14.0 cm와 16.5 cm가 각각 26주와 32주이고, 일본잎갈나무의 경우는 각각 32주와 48주이었다. 이들 정각재의 재장방향과 두께방향의 수분경사는 비교적 완만하였다. 일본잎갈나무의 수분경사는 소나무의 것보다 컸었고, 일본잎갈나무의 변장의 크기가 수분경사에 미치는 영향은 소나무의 것보다 컸었다.

• 한국대기환경학회지
• /
• 제12권3호
• /
• pp.263-268
• /
• 1996

This study was conducted for the assessment of the effects of acid rain and soil fertilizers on photosynthetic rate, was content, and contact angle on 5-year seedlings of Japanese red pine (Pinus densiflora Sieb. et Zucc.) leaves. The seedlings were exposed to pH 3.0 (simulated acid rain), pH 6.5 (groung water) and rain (pH around 4.6). The seedlings were also treated with $Ca(OH)_2, Mg(OH)_2, and Ca(OH)_2 + Mg(OH)_2 + C.F.(compound fertilizer)$. Photosynthetic rate, stomatal conductance, was content, contact angle value, and mineral nutrient content of the leaves were measured and the results were as follows: 1. Photosynthetic rate and stomatal conductance of the leaves increased with the increase of pH. Photosynthetic rate and stomatal conductance increased with application of soil fertilizer in the pH 3.0 treatment, but showed no changes in the rain and the pH 6.5. 2. Contact angle value and was content of the leaves did not change with the pH treatment, but increased with the fertilizer treatments. 3. Mineral nutrient contents of the leaves were lowest in the rain treatment and highest in the pH 6.5 treatment. The increase of mineral nutrient contents was observed with the soil fertilizer treatments.

• Molecules and Cells
• /
• 제20권2호
• /
• pp.201-209
• /
• 2005

We have constructed an AFLP-based linkage map of Japanese red pine (Pinus densiflora Siebold et Zucc.) using haploid DNA samples of 96 megagametophytes from a single maternal tree, selection clone Kyungbuk 4. Twenty-eight primer pairs generated a total of 5,780 AFLP fragments. Five hundreds and thirteen fragments were verified as genetic markers with two alleles by their Mendelian segregation. At the linkage criteria LOD 4.0 and maximum recombination fraction 0.25(${\theta}$), a total of 152 markers constituted 25 framework maps for 19 major linkage groups. The maps spanned a total length of 2,341 cM with an average framework marker spacing of 18.4 cM. The estimated genome size was 2,662 cM. With an assumption of equal marker density, 82.2% of the estimated genome would be within 10 cM of one of the 230 linked markers, and 68.1% would be within 10 cM of one of the 152 framework markers. We evaluated map completeness in terms of LOD value, marker density, genome length, and map coverage. The resulting map will provide crucial information for future genomic studies of the Japanese red pine, in particular for QTL mapping of economically important breeding target traits.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.141-148
• /
• 2013

The goal of this study was to find the optimum lamina size from red pine (Pinus densiflora) and Japanese cedar (Cryptomeria japonica) logs for the cross laminated timber (CLT) production. From visual inspection of the logs from two species, red pine log showed a larger knot and warp compared to the Japanese cedar. Different cross-sectional sizes of lamina ($110mm{\times}30mm$, $110mm{\times}40mm$, $110mm{\times}50mm$, $50mm{\times}30mm$, $30mm{\times}30mm$) from two species were analyzed for yield and grade. Regardless of the species, the optimized cross sectional size for maximizing the yield was $110mm{\times}30mm$. In grading for the different size laminas from Japanese cedar and red pine, a higher percentage of the first and second grade was found from the $110mm{\times}30mm$ lamina cut.