• Journal of the Korean Wood Science and Technology
• /
• v.37 no.5
• /
• pp.465-473
• /
• 2009

Three failure theories were studied to evaluate the wood strength variation with grain slope. Maximum stress theory, Tsai-Hill theory and Hankinson formula were presented to hypothesize the failure of wood according to grain slope to loading direction. Red pine and Japanese larch were used as materials to simulate failure strength prediction with grain slope. Calculation of strength results was that the strength of wood drops rapidly between parallel to grain orientation (0 degree) and 15 degree grain orientation. The strength of wood with grain orientation were somewhat different at small grain angles among failure theories, and this tendency was due to tension and compression distinction, and shear accounting in each theories. For the above 45 degree grain orientation, the predicted failure strength of wood with grain variation were very close in each failure theories and were useful in assessing failure strength of wood. The applicable these theories should be considered that the wood has different behavior in tension and compression, and this lead to different strength at small grain angles in each theories. Furthermore, reconsideration is needed to assess the failure strength of wood at small grain angles in Hankinson formula and further studies are necessary to accounting for shear behavior at small grain angles.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.101-111
• /
• 2014

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaining (BR) and bark-remaining-coating (BRC) treatments on the air circulating oven-drying characteristics of Japanese larch hollowed round-post was evaluated. The drying times of the hollowed round-posts for control, VD, HCO and BR specimens were 72, 168, 204 and 240 hours, respectively, from the initial MC to about 8% MC, which was recommended as the indoor in-use MC. The temperature in the hole of the VD specimen was lower than that of wood and the difference between air temperature in the hole and wood temperature became large during drying period. The vapor pressure of air in the hole was higher than that of inside wood for all specimens except VD specimen. The surface checks on all specimens were observed in increasing order of BR, BRC, UC, HCO and VD specimens.

• Journal of Forest and Environmental Science
• /
• v.27 no.2
• /
• pp.113-118
• /
• 2011

This study was carried out to analyze annual diameter growth characteristics for major 11 tree species using the data for Gangwon province of the National Forest Resources Inventory in 2007. The annual diameter growth of coniferous species was 5.02 mm, 4.70 mm, and 3.90 mm in Korean white pine, Japanese larch, and Korean red pine, respectively. In growths of the deciduous trees, dogwood, basswood, and cork oak had 3.55 mm, 3.48 mm and 3.01 mm, respectively. Average of the annual diameter growths for all species was 3.38 mm. The relationship between diameter growth and age class showed that the growth rate decreased for all species as age increased. The age class II had the highest annual diameter rate. In relation of the stand density(trees per hectare) and diameter growth, the diameter growth tended to decrease as the stand density increased for most species, especially Korean white pine, cork oak, and basswood. Finally age had the highest value in the correlation coefficients between measurement factor and growth rate regardless of species.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.5
• /
• pp.345-357
• /
• 2023

The present study conducted a stem analysis to trace growth information of Japanese larch (Larix kaempferi) and predict the future changes in growth volume. For this purpose, six L. kaempferi trees over 47 years old were cut at 1-2 m intervals from a height of 0.2 m, and circular plates of 5 cm thickness were collected for stem analysis. The analysis indicated that approximately 1-8 years are required to grow up to chest height. The annual height and diameter growth increased rapidly until the trees are 15 years old and gradually decreased after 20 years. The volume of 30-year-old trees in Oegam-ri forests, which were well-managed after artificial reforestation, was 0.4837 m³, whereas that in unmanaged Singi-ri forests was 0.1956 m³. Although the volume of individual trees differed greatly depending on the forest management status, it was found that the volume increased by 1.67-1.76, 2.49, and 3.49 times at 40, 50, and 60 years age, respectively, compared to the legal harvesting age 30. Therefore, factors such as the carbon dioxide reduction effect, forest management benefits, and the condition of trees at the site should be considered before harvesting trees.

• Journal of Korean Society of Forest Science
• /
• v.85 no.2
• /
• pp.316-324
• /
• 1996

This study was conducted by relative time study to identify the allowance time and basic work time, which is together composed of the total work time, in the wage composition and work process composition. This study was done for the case of a basic one person a group from thinning treatment for some conifer species such as Japanese red pine, Japanese larch, pitch pine and Korean pine. 1. In order to apply the Japanese allowance time of four species to the general conifer case, the maximum value of allowance time composition value among those of four species was selected. The results are as follows: delay time for person 1.8%, rest time 14.1%, delay time for machine 12.5% and wating time 0.4%. The some of ratios of adjustment allowance time is 28.8%. 2. Estimated wage basis time table, which can be used for wage table or process table, was prepared by adding up adjusted general allowance time and standard work time estimated by estimation equation for each species through the time study.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.1-12
• /
• 2007

For the purpose of effective utilization of domestic second-grown larch as structural members, post and beam construction applying traditional construction to Japanese larch glulam members was adopted with processing by machine pre-cut method. In general, horizontal shear test by KS F 2154 is conducted to assess the horizontal shear properties of the wooden structure by post and beam construction. The frame was consisted of post and beam member with appropriate fasteners, and members have their own processed parts (notch, hole, etc.) that can be well-connected each other. The shear wall was consisted of the frame with screw-nail sheathed panel (OSB). The results of horizontal shear loading tests without vertical loads conducted on the frame and the shear wall structures, the maximum strengths were about 1.9 kN/m and about 9.7 kN/m, the shear rigidities were about 167 kN/rad, 8198 kN/rad, respectively. The strength proportion of the frame specimen was about 20% of the wall's and about 2% in initial stiffness. Nail failures are remarkable on the shear wall specimen with punching shears and shear failures. The shear load factor for the shear wall specimen by the method of Architectural Institute of Japan was 1.5, which was obtained by the bi-linear method. Loading method should be considered to obtain smooth load-deformation relationship. For the better shear performance of the structures, column base and post and beam connections and sheathed panel should be further examined as well.

• Korean Journal of Environment and Ecology
• /
• v.21 no.4
• /
• pp.356-365
• /
• 2007

This study was conducted to evaluate the changed vegetational community structure according to vegetational succession in Chiaksan National Park of Korea by applying ordination and classification method of floristic composition along with the actual vegetation by correlation. As for the ratio of actual vegetation, Mongolian oak forest(33.1%) was the highest, followed by mixed forest(16.2%), Japanese larch forest(15.6%), deciduous broad-leaved forest(14.7%), red pine forest(11.1%), Korean pine forest(2.3%) and Pitch pine forest(0.1%), respectively. The vegetation was classified into Acer pseudosieboidianum-Quercus mongolica community, Cornus controversa-Carpinus cordata community, Quercus sonata community, Pinus densiflora community and afforestation. The Acer pseudosieboldianum-Quercus mongolica community-a subordinately ranked community-was divided into Carpinus laxiflora-Sassa borealis community, Fraxinus rhynchophylla community and Symplocos chinensis for. pilosa-Carex siderosticta community. The results of community classification using by ordination and classification method of floristic composition were similar to each other. The vegetational succession, with the combination of Quercus mongolica, Acer pseudosieboldianum and Rhododendron schlippenbachii, was predicted to form a climax forest from above the hillside.

• Journal of Korean Society of Forest Science
• /
• v.74 no.1
• /
• pp.82-87
• /
• 1986

Noticed that large number of the Korean white pine (Pinus koraiensis S. et Z.) has lost its typical excurrent tree from by removal of apical shoot in the process of cone harvesting, the investigation and analysis for the species were made on the basis of the relationship among DBH, total height, merchantable height, and merchantable volume, compared with normally grown Japanese larch (Larix leptolepis Gordon). One hundred sample trees for each species were selected in the same aged stands for the study. Results have indicated that the pine has shown abnormal height growth pattern mainly by the disturbance of external artificial force. The pine's forked and/or crooked stems by the reason lave led the result of less merchantable volume in the same DBH classes. Consequently, the pine would have undesirable tree form in terms of timber production, unless free from apical shoot disturbances. Considered to the merit of the Korean white pine that can produce timber and pine nuts, management alternatives for the pine stand were suggested to achieve maximum rate of return for the silvicultural investment.

• Journal of Environmental Science International
• /
• v.21 no.1
• /
• pp.97-103
• /
• 2012

Suspended wood waste was being inflow into the dam and the problem of waste disposal has been occurred. In this study, ethanol production using woody floater wastes was performed to estimate value in use for raw material of renewable energy. To achieve the goal, experiments of acid hydrolysis and ethanol fermentation using dam woody floater as raw materials for bioethanol was carried out. In the results of field survey in the chungju dam, kind of woody floater was mainly Japanese larch (Larix leptolepis) and hybrid poplar (Populus tomentiglandulosa). The results of sugar extraction showed that sugar content was higher in Larix leptolepis than Populus tomentiglandulosa. Extracted sugar from wood waste was effective consumed by yeast(P. Stipitis and S cerevisiae). In the experiment consumption of sugar including glucose, galactose and xylose, the consumption rate of S. cerevisiae is faster than that of P. stipitis. and efficiency for ethanol production is higer in S. cerevisiae than P. stipitis. Also it can be confirmed that resource as ethanol production using wood waste was available.

• Journal of the Korea Furniture Society
• /
• v.21 no.1
• /
• pp.26-39
• /
• 2010

This is a leading study to replace the structural analysis methodology on the specific traditional joint by a numerical analysis. Tests were carried out to test the compressive methodologies with the numerical results. The Japanese larch was used as a sample. The Orthotropic property of wood was specifically considered for the finite element numerical analysis. Linear numerical analysis and non-linear numerical analysis for the BEAM element and the two SOLID elements of ANSYS were used to analyze the compressive performance. In addition, more finely divided elements were used to raise the accuracy of the numerical result. Finally, the statistically significant differences were tested between that of the analytical and numerical results. It could be concluded that the SOLID 64 element shows the most optimum result when the non-linear analysis with the more finely divided element was used. However, finely dividing of the element is a considerable time consuming process, and it is quite difficult to raise the accuracy of the non-linear numerical analysis. Therefore, if considering the vertical displacement to be of the only interest, the BEAM element is more efficient than the SOLID element because the BEAM element is reflected as a simple line, which is less time consuming and difficult in dividing the elements. But, the BEAM element cannot accurately model the knot as a strength defect factor which is an important property in the orthotropic property of wood. Therefore, the SOLID element should be used to model the strength defect factor, knot, as it can be efficiently applied on the structural size flexure member which could be more strongly effected by the knot. In addition, it is useful at times when the failure types of members are to be more closely investigated, as the SOLID element is able to examine the local stress distribution of the member. The conclusion drawn by this study is of the good concordance between analytical results and numerical results of compressive wood members, but how orthotropic properties should only be considered. The numerical analysis on the specific Korean traditional joints will be based on the current study results.