• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1434-1435
• /
• 2006

본 연구에서는 polymer gate insulators에 따른 pentacene 유기 박막 트랜지스터 (Organic Thin-Film Transistors)의 전기적 특성을 atom force microscope (AFM), x-ray diffraction (XRD) 그리고 I-V 측정을 이용하여 분석하였다. Pentacene 박막 트랜지스터의 전기적 특성은 pentacene의 증착 조건뿐만 아니라 polymer gate insulator에 따라 크게 영향을 받는다. 따라서 다양한 polymer 기판 위에 온도, 두께 그리고 증착 속도에 따라 pentacene을 증착 하였다. 그리고 증착된 pentacne을 AFM, XRD를 이용하여 pentacene의 구조, 결정화 그리고 grain 크기 등을 분석하였다. 또한 inverted stagger며 구조의 pentacene 박막 트랜지스터 소자를 제작하고 I-V 측정하여 그 결과를 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.216-217
• /
• 2006

A common problem in many fields of cryogenic power engineering is to apply high voltage to cold parts of superconducting equipment. In many of these cases a bushing provides electrical insulation for the conductor which makes the transition from ambient temperature to the cold environment. The cryogenic high voltage bushing for the 154kV, 100MVA high temperature superconducting(HTS) transformer is described. The bushing is energized with the line-to-ground voltage between the coaxial center and outer surrounding conductors, in the axial direction there is a temperature difference from ambient to about 77 K. For the insulation design of cryogenic bushing, the arrangement of condenser cone and electrical insulation characteristics of GFRP, Air, $LN_2$ and $GN_2$ were discussed in this paper.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1530-1533
• /
• 2005

Total 12 units of high power klystron-modulator systems as microwave source is under operation for 2.5-GeV electron linear accelerator in Pohang Light Source(PLS) linac. RF power and beam power of klystron are precisely measured for the effective control of electron beam. A precise measurement and measurement equipment with good response characteristics are required for this. Input power of klystron is calculated from the applied voltage and the current on its cathode. Tiny measurement error severely effects RF output power value of klystron. Therefore, special care is needed to measure precise beam voltage. Capacitive voltage divider(CVD) unit is intended for the measurement of beam voltage of 400 kV generated from the pulsed klystron-modulator system. Main parameter to determine the standard capacitance in the high arm of CVD is dielectric constant of insulation oil. Therefore CVD should be designed to have a minimum capacitance variation due to voltage, frequency and temperature in the measurement range. This paper will discuss the analysis of capacitive voltage divider for a pulsed high-voltage measurement, and the empirical relations between capacitance and oil temperature variation.

• Journal of the Korean Society of Safety
• /
• v.34 no.1
• /
• pp.8-13
• /
• 2019

Weight and elongation changes of IV and HIV insulations were measured simultaneously at several given temperature of $80^{\circ}C$, $90^{\circ}C$ and $100^{\circ}C$. And the lifetime was predicted using the Arrhenius model. Based on the initial weight values, a 50% elongation reduction was seen at 6.96% for the IV insulation and 10.29% for the HIV insulation. The activation energy from the slope of the lifetime regression equation was calculated as 92.895 kJ/mol(0.9632 eV) for the IV insulation and 95.213 kJ/mol(0.9873 eV) for the HIV insulation. Also, the expected lifetime at the operating temperature of $30^{\circ}C$ to $90^{\circ}C$ is 2.02 to 94.32 years, and longer lifetime was predicted on HIV insulated wires than on IV insulated wires. As a result, it was found that the thermal characteristics of the HIV insulated wires were about 12.44% better than those of IV insulated wires under the same conditions of use.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.5
• /
• pp.607-613
• /
• 2010

The influence of dietary supplementation with blended essential oil on growth performance, nutrient digestibility, blood profiles and fecal characteristics was evaluated in 125 crossed ((Duroc ${\times}$Yorkshire) ${\times}$Landrace) pigs (6.21${\pm}$0.20 kg initial body weight and 21 d average age). The pigs were allotted to the following treatments: i) NC (antibiotic free diet), ii) PC (NC diet+44 ppm tylosin), iii) T1 (NC diet+0.1% essential oil), iv) T2 (NC diet+0.1% essential oil (with 0.3% Benzoic acid)) and v) T3 (NC+22 ppm tylosin and 0.05% essential oil). Average daily gain (ADG) was improved in the T2 group on d 14 (p<0.05). In addition, nutrient digestibility was partially affected (both positively and negatively) by the treatments. Furthermore, the immune system was stimulated and the fecal pH and fecal noxious gases were improved in pigs that received the diets supplemented with essential oil (p<0.05). The appearance and score of diarrhea also tended to be lower in pigs that were subjected to the essential oil treatments. Collectively, the results of this study indicate that supplementation of the diet with blended essential oils could replace treatment with antibiotics to improve growth performance and fecal characteristics.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1765-1768
• /
• 1996

It is well known that the degradation transformer oil is mainly effected to the failure of transformer. In this paper it is discussed the characteristics of the degradation sensor checking transformer oil condition in live line. The degadation sensor composed with base ring, electrodes and porous ceramic passed through the transformer oil and checked the transformer oil condition with sensor's leakage current. It is important to minimize the leakage current of base ring and connection parts. To investigate the leakage current of base ring and connection parts it is examined the characteristics of V-T-I and DC 2 KV and other examinations. It is verified that ionized transformer caused by the expansion of oil temperature increase in the leakage current of porous ceramic sensor. It is certificated that the leakage current of other parts of porous ceramic is very small (about 2 %) than the porous ceramic and it is confirmed that the leakage current in porous ceramic is changed sensitively according to the new oil(NO) and and the degradation oil(DO).

• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.329-338
• /
• 2013

In this paper, the charging characteristics of series resonant type high voltage capacitor chargers considering the transformer stray capacitance have been studied. The principles of operation for the four operational modes and the mode changes for the four different switching frequency sections are explained and analyzed in the range of switching frequency below the resonant frequency. It is confirmed that the average charging currents derived from the above analysis results have non-linear characteristics in each of the four modes. The resonant current, resonant voltage, charging current, and charging time of this capacitor charger as variations of the switching frequency, series parallel capacitance ratio ($k=C_p/C_s$), and output voltage are calculated. From the calculation results, the advantages and disadvantages arising from the parallel connection of this stray capacitance are described. Some methods to minimize charging time of this capacitor charger are suggested. In addition, the results of a comparative test using two transformers whose stray capacitances are different are described. A 1.8 kJ/s prototype capacitor charger is assembled with a TI28335 DSP controller and a 40 kJ, 7 kV capacitor. The analysis results are verified by the experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.286-291
• /
• 2015

LLC resonant converter is used to control laser output power in Nd:YAG laser. Zero voltage switching (ZVS) is implemented to minimize the switching loss which is adopting the LLC resonant converter. In the spot welding processing of metal thin films, the processing quality is decided by the laser beam output energy of single pulse. We decide to the 50 [J] as the single pulse laser beam energy. Laser output power is investigated and experimented by changing the output current. That current is controled by the charging voltage of capacitor. From those results, we obtained the maximum laser output of 58.2 [J] and the conversion efficiency of 2.52% at the discharge voltage of 620V and the discharge current of 861 [A] and the pulse repetition rate of 1 [Hz] at the charging capacitor of 12,000 [${\mu}F$].

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.47-47
• /
• 2009

용착금속의 미세조직은 크게 Acicular ferrite(AF), Ferrite with aligned second phase(FS), Primary ferrite(=Grain boundary Ferrite) 등으로 나눌 수 있다. 이 중 침상형 페라이트(AF)는 인성과 강도를 동시에 증가시킬 수 있으므로 이를 다량 확보하는 것이 용접산업의 관건이다. 본 연구에서는 침상형 페라이트 발생에 기여한다고 알려진 Ti 함량을 용착금속에서 단계적으로 조절하여 나타나는 미세조직과 특성변화를 관찰하였다. 모재는 HSB-600을 사용하였으며 용접재료는 ER100S-G급의 Ti가 함유되어 있는 것(A)과 미함유된 것(B)을 사용하였다. 모재 성분의 희석을 방지하기 위해 V-Groove 가공 후 Buttering 용접을 실시하였다. 중앙에 가공된 V-그루브에 이들 재료를 적절히 조합하고 용접(입열량 20kJ/cm)하여 Ti함유량을 총 4가지(0.002~0.025% Ti)로 제어하였다. 용접 후 각각의 시편에 대해 미세조직, 충격시험, O/N분석, 성분분석 등의 시험을 진행하였다. 미세조직 관찰결과 Ti함량이 증가할수록 AF는 증가하고 FS는 감소함을 확인할 수 있었으며 충격시험결과 Ti가 많이 함유된 시편일수록 더 낮은 연성취성 천이온도(DBTT)를 나타내었다. EDS와 SEM으로 관찰한 결과 Ti함량 증가에 따라 비금속개재물의 크기는 작아지고 밀도는 높아지는 것을 확인할 수 있었으며 개재물 내에서의 Ti함량도 더 많아지는 것을 확인 할 수 있었다.

• Archives of design research
• /
• no.16
• /
• pp.17-25
• /
• 1996

, \l!ernatives in multi dimensional decision prohlems generally possess numerous attrihutes by which they can be describ('d and compared, The ('\';dllation factors include all attributes that have Ic\'(']s specified by quantitative and qualitativc objectil'l'S, Howev'('f since qualitative factors arc difficul! to quantify as num('ral estimates, these factors have tended to bl' ignored without regard for their importance to human contrnl. In this study, the author adapted :j ('va]uation methods with critrria which have qualitative and qualitative attributes: the Intuitive Evaluation ~1cthods the Accumulativc' Evaluation Model the Benchmarking Evaluation Methods, and studied the corrC'iation between them, The results show that Ill(' :j Mrthods have reciprocal relationships under reliability (r=O, (XX)]] In order to removl' obstacles of desi!;n ev'aluation ( lots of timl' l'llnsumption, constr;lints of placc" difficulties of hu!;!' data procc'ssin!;), it is necessary to be developed a new ('va]uation syst('rn which could prov'idc' effective rat in!; of desi!;n v'alm's 10 make value judw'rnents, , \l!ernatives in multi dimensional decision prohlems generally possess numerous attrihutes by which they can be describ('d and compared, The ('\';dllation factors include all attributes that have Ic\'(']s specified by quantitative and qualitativc objectil'l'S, Howev'('f since qualitative factors arc difficul! to quantify as num('ral estimates, these factors have tended to bl' ignored without regard for their importance to human contrnl. In this study, the author adapted :j ('va]uation methods with critrria which have qualitative and qualitative attributes: the Intuitive Evaluation ~1cthods the Accumulativc' Evaluation Model the Benchmarking Evaluation Methods, and studied the corrC'iation between them, The results show that Ill(' :j Mrthods have reciprocal relationships under reliability (r=O, (XX)]] In order to removl' obstacles of desi!;n ev'aluation ( lots of timl' l'llnsumption, constr;lints of placc" difficulties of hu!;!' data procc'ssin!;), it is necessary to be developed a new ('va]uation syst('rn which could prov'idc' effective rat in!; of desi!;n v'alm's 10 make value judw'rnents,alm's 10 make value judw'rnents,