• Progress in Superconductivity
• /
• v.1 no.2
• /
• pp.110-114
• /
• 2000

We have investigated the Josephson vortex dynamics in $Bi_2Sr_2CaCu_2O{8+\delta}$ intrinsic Josephson junctions subjected to a magnetic field parallel to $CuO_2$ planes. We investigated mesas with $40\times40{\mu}m^2$ in size and containing 6 and 20. intrinsic junctions. The zero field I-V characteristics exhibited a typical hysteretic, multi-branched nature of the intrinsic Josephson effect. At high magnetic fields (H>1.5 T), I-V characteristics showed flux flow steps. The Swihart velocity obtained from this observation was about $4.2\times10^5$ m/s, which was the lowest mode electromagnetic wave velocity of N coupled stack. The experimental I-V curves fitted well into the simple model of Cherenkov radiation including Ohmic and non-linear dissipation terms. This suggests that the dissipation mechanism of Josephson vortex be due to both Cherenkov radiation and quasiparticle tunneling current.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.163-171
• /
• 2000

The aim this study is to provide fundamental informations for the development of magneticfluid damper. To achieve the aim. the damping effect of magneticfluid is investigated by experiments that the diameter of inner circular bar and the input amplitude vary in the magnetic field generated by the permanent magnet and the electromagnet. From the study, the following conclusive remarks can be made. As the diameter of inner circular bar and the input amplitude increase. the damping effect is improved. And we can know that as the contact area between inner circular bar and magneticfluid increases, damping ratio is improved. Also we consider the cases that there is magnetism generated by electromagnet and DC voltage is supplied to electromagnet from 10V to 50V by 10V. In these cases, the amplitude ratio decreases sharply from 1.8 1.0 And for these cases, the damping ratio is .745.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2011-2016
• /
• 2018

In this study, we have been investigated pin to plate pulsed bi-polar discharges in saline solutions, where bubble generation occurs. We integrate basic I-V-t electrical characteristics with the ICCD shadowgraph images, and finally instant and time averaged I-V waveforms. We observed that the bubble formation phase dynamics is quite different corresponding to the polarity applied to the pin electrode. When the pin electrode is a cathode, the bubble tends to be periodically detached from the pin electrode and the numerous tiny voltage spikes occur related to the electron emission from a pin cathode casing via, we judge from, direct dissociation of water molecules by energetic electrons. On the contrary, the bubble tends to stick to the pin electrode, when the pin electrode is anode; the bubble grows in size throughout the pulse duration. The dynamic electrical characteristics relative to the applied polarity of a pin electrode are presented and discussed by analysis of time averaged I-V waveforms.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.05
• /
• pp.41-44
• /
• 1996

There are studied for filmness methods due to disadvantage of conventional X-ray system. Have high DQE, high SNR, amorphous selenium was investigated with image plate. In this point, characteristics of all amorphous selenium image plate was investigated to understand the relationship between the amount of the X-ray exposure and the superficial charge potential in this study. Specially, changes in charge at the surface of the amorphous selenium plate with respect to change of X-ray energy(KeV) was investigated. It was found that the surface charge potential at the amorphous selenium inclosed with respect to the increse in X-ray exposure and that the changed surface potential was a semilinearity in 12.5KeV - 22.5KeV range. Therefore, which suggests that these results call be applied to the development of X-ray image plate.

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.818-824
• /
• 2019

In the present work, we determined the gamma-ray attenuation characteristics of eight different polymers(Polyamide (Nylon 6) (PA-6), polyacrylonitrile (PAN), polyvinylidenechloride (PVDC), polyaniline (PANI), polyethyleneterephthalate (PET), polyphenylenesulfide (PPS), polypyrrole (PPy) and polytetrafluoroethylene (PTFE)) using transmission geometry utilizing the high resolution HPGe detector and different radioactive sources in the energy range 81-1333 keV. The experimental linear attenuation coefficient values are compared with theoretical data (WinXCOM data). The linear attenuation coefficient of all polymers reduced quickly with the increase in energy, at the beginning, while decrease more slowly in the region from 267 keV to 835 keV. The effective atomic number of PVDC and PTFE are comparatively higher than the $Z_{eff}$ of the remaining polymers, while PA-6 possesses the lowest effective atomic number. The half value layer results showed that PTFE ($C_2F_4$, highest density) is more effective to attenuate the gamma photons. Also, the theoretical results of macroscopic effective removal cross section for fast neutrons ($\sum_{R}$) were computed to investigate the neutron attenuation characteristics. It is found that the $\sum_{R}$ values of the eight investigated polymers are close and ranged from $0.07058cm^{-1}$ for PVDC to $0.11510cm^{-1}$ for PA-6.

• International Journal of Automotive Technology
• /
• v.8 no.3
• /
• pp.269-274
• /
• 2007

A prior fundamental study was executed using a constant volume chamber (CVC) to improve the burning characteristics of lean pre-mixture by the injection of active radicals generated in the sub-chamber of the CVC. The Radical ignition (RI) technique shows remarkable progress in the burning velocity and combustible lean limit compared with the results of the spark ignition (SI) technique. The optimum design value of the sub-chamber geometry is near $0.11cm^{-1}$ for the ratio of the total area of the holes to the sub-chamber volume $(A_h/V_s)$. In this study, based on the former experimental results, the additional works have been performed to examine the effects of the geometry change in the number $(N_h)$, the total section area $(A_h)$, and diameter $(D_h)$ of the passage holes on the combustion characteristics in the CVC. Also ambient conditions such as the initial temperature and the initial pressure of the mixture were selected as experimental parameters and the effects of residual gas at the chamber on the combustion characteristics were investigated. As a result, the correlation between the passage hole number and overall passage hole area was grasped. The effects of the initial temperature were significant, but on the other hand, those of the initial pressure were weak. A more detailed analysis on the residual gas is required in the future.

• Horticultural Science & Technology
• /
• v.32 no.5
• /
• pp.584-589
• /
• 2014

Jeffersonia dubia is a spring-flowering perennial found in rich forests in Korea and Northern China and has potential as an ornamental or medicinal plant. However, illegal picking and land use change have decreased the number of populations and overall population size of this plant in its natural habitat. Although J. dubia has been reported to be a shade-preferring plant, no study has determined the optimum light intensity for its growth. The objectives of this work were to observe the effects of various shading levels on the physiological responses of J. dubia and to determine the proper shading level for cultivation. Treatments consisted of four shading levels (0%, 50%, 75%, and 95% shade) imposed using black mesh cloth. The number of leaves and dry weight increased with decreased shading. The shoot-to-root ratio increased with increased shading, mainly due to decreased root dry weight under shading. Plants showed low net $CO_2$ assimilation rates and $F_v/F_m$ values combined with low dry matter levels when grown under 0% shade (full sunlight). These results indicate that J. dubia plants experience excessive irradiance without shading, resulting in damage to the photosynthetic apparatus. By contrast, the net photosynthesis rate increased as the shading level increased. $F_v/F_m$, the potential efficiency of PSII, was 0.8 under 95% shade, indicating that J. dubia is well-adapted under heavy shading. However, the low dry matter of plants in the 95% shade treatment indicated that the low light intensity under 95% shade led to a decline in plant growth. Thus, moderate light (50% shading) is recommended for cultivating J. dubia without physiological defects.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1851-1853
• /
• 2004

The important consideration in laboratory designing and construction of the artificial pollution testing facilities including 300kV, 1800kVA AC test system, which enable to test and evaluate the UHV dielectric performance of power insulators up to transmission class, has been dealt in this paper. To evaluate the performance characteristics against contamination for various power installation, especially for the insulators and kinds of bushings, brief investigation and an analysis of test objects and related international codes and standards have been conducted. With the special consideration concerning other matters in designing of these testing facilities have been described with the fixed ratings and references.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.154-154
• /
• 2009

Cr capping layer를 이용하여 Titanium germanide의 열적 안정성을 향상시키는 연구를 수행하였다. n-type Ge(100) 기판 위에 전자빔 증착기를 이용하여 30nm 두께의 Ti와 Cr capping layer를 증착하고 $400\;^{\circ}C$에서 $800\;^{\circ}C$까지 30초간 N2 분위기로 급속 열처리하여 Ti germanide를 형성하였다. XRD결과로부터 Cr capping layer의 유무에 관계 없이 Ti germanide가 형성된 것을 관찰할 수 있었다. Ge 기판 위에 CTLM 패턴을 형성하고 실험을 진행하여 Ti germanide의 I-V 측정 데이터를 통해 Ohmic 특성을 알아보았고, contact resistance, sheet resistance, specific contact resistance를 구하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1566-1570
• /
• 2005

The aspherical lenses are used as optical lens of HMD optical system. The optimum cutting condition of PMMA lens sample with ultra precision SPDT, the diamond tool nose radius, the cutting speed, the feed rate, the depth of cut, and cutting fluid type are found. The demanded surface roughness 10 nm Ra, aspherical form error $1.0\;\mu{m}$ P-V for aspherical lens of optical data storage device are satisfied.