• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.232-232
• /
• 2010

Simulation Program (AFORS-HET 2.4.1) was used, include the basic structure of crystalline silicon thin film as above, under the intrinsic a-Si:H films bonded symmetrical structure (Symmetrical structure) were used. The structure of ITO, a-Si p-type, intrinsic a-Si, c-Si, intrinsic a-Si, a-Si n-type, metal (Al) layer has one of the seven. When thickness for each layer was given the change, the changes of a-Si p-type layer and the intrinsic a-Si layer on top had an impact on efficiency. Efficiency ratio of p-type a-Si:H layer thickness was sensitive to, especially a-Si: H layer thickness is increased in a rapid decrease in Jsc and FF, and efficiency was also decreased.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.65-67
• /
• 2005

The Al electrode for OLED was prepared by Facing Targets Sputtering(FTS) system which can reduce the damage of organic layer. The Al thin films were deposited on the cell (Lif/EML/HTL/Bottom electrode : ITO) for examination the current-voltage properties of OLED with magnetic field distribution between two faced targets. Thickness and current-voltage properties of Al thin films are measured by ${\alpha}-step$ and semiconductor parameter analyzer (HP4156A), respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.317-317
• /
• 2010

ZnO나노와이어는 높은 투과도, 화학 및 열적 안정성을 가지며, 유기태양전지에 적용하였을 때 Active Layer의 표면적 증가, 전자의 수집 및 전달에 용이한 장점가지고 있어 하이브리드 유기 태양전지에 적용되고 있다. ZnO나노와이어와 P3HT/PCBM을 사용한 하이브리드 유기태양전지는 Active Layer의 열처리 온도를 변화시켜 ITO/AZO/ZnO wire/PCBM:P3HT/PEDOT:PSS/Ag구조로 제작되었다. ZnO나노와이어는 AZO를 Seed로 사용하고 Znc nitrate hydrate와 hexamethylenetetramine을 혼합하여 수열합성법으로 성장 후, P3HT:PCBM, PEDOT:PSS을 Spin Coating법으로 형성하였다. UV-vis와 Solar simulator를 통하여 Active Layer의 열처리 온도에 따른 태양전지의 특성을 분석하였다.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1469-1471
• /
• 1997

In this study, Organic electroluminescent(EU devices with multilayer structures were fabricated using tris (8-hydroxy quinolinate) aluminum($Alq_3$) as an electron-tran sporting emitting layer and TPD(N,N'-diphenyl-N,N'-bis(3-methylphenyl)-[1,1'-biphenyl]-4,4'-diamine : aromatic diamine) as a hole-transporting layer. A cell with a structure of glass substrate/indium-tin-oxide(ITO)/$Alq_3$/TPD/Mg:In exhibited bright green electroluminescence from the TPD layer. The peak intensity of TPD and $Alq_3$ different from spin coating and vacuum evaporation. The peak emission energy shifts to a higher energy with deposition technique. An emission peak at 500nm was achieved at a driving voltage of 30V.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.1
• /
• pp.46-54
• /
• 1995

An electrochromic(EC) cell was constructed using $WO_3$ as a electrochromic material and NiO as a counter electrode, deposited onto ITO-coated glass by the implementation of electron beam evaporation. The electrolytic media were both lithium and proton conducting polymers such as poly-acrylonitrile(PAN)-$LiClO_4$, poly-ethylene oxide(PEO)-$LiClO_4$, poly-vinyl butyral(PVB)-LiCl and PVB-H$_3$$PO_4$. Potentiodynamic cycling of the cells using PAN-$LiClO_4$, or PVB-$H_3$$PO_4$ electrolyte yielded a transmission variation of more than 40% at the wavelength of 632.8 nm within less than 10 sec response time at room temperature. These results indicate that these electrolytes, transparent in gel type, are premising for the application in large area electrochromic windows.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.403-406
• /
• 1998

Electroluminescence(EL) come from the light emission obtained by electrical excitation energy passing through a phosphor layer under applied high electrical field. The preparation and characterizations of light emitting ACPEL(alternating-current powder electroluminescent) cell based on two kinds of phosphor mixed ZnS:Mn, Cu and ZnS:Cu phosphor. Basic structure is ITO/Mixed Phosphor/insulator/Al sheet, each layer was mixed by binder, which concentration 11p for phosphor, 8p for insulator. Dielectric properties was investigated first and emission properties of P-LED based on ZnS:Mn,Cu/ZnS:Cu,Br mixture. Emission spectra exhibits two kinds of main peaks at 100V, 1kHz sinusoidal excitation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.163-166
• /
• 1997

Electroluminescent(EL) dcvice based on organic thin layers have attracted lots of interests because of thier possible application as large-area light-emitting displays. It was known that MEH-PPV and 1, 1, 4, 4, -Tetraphenyl-1, 3-butadiene(TPB) has red and blue emission peak at 580nm and 480nm, respectively. In this study, MEH-PPV films and TPB films were prepared by spin coating and vacuum deposition method, respectively. Films of MEH-PPV and TPB double layer were also prepared by the same method. Photoluminescent(PL) characteristics of these single and doubler layers were investigated, where a cell structure of glass substrate/ITO/MEH-PPV and/or TPB/Al was employed. It was found that the photoluminescent efficiency of TPB film was higher than that of MEH-PPV film with a single layer and also with a double structure. These films have also different I-V characteristics.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.449-453
• /
• 1996

In order to improve EL performance, anthracene was doped into the 8-hydroxyquinoline-aluminum (Alq$^3$) light-emitting layer of organic double layered EL cells. The EL cells were fabricated on ITO glass substrates by vacuum deposition. Doping of anthracene to the light-emitting $Alq^3$layer was performed by means of co-evaporation. The doping concentration was changed in the range of 5 to 30 wt.%. It was confirmed that anthracene doping of appropriate concentration increased the available current density and brightness of the EL cells. Carrier mobility of the $Alq^3$ layer was measured by time of flight method. The influence of anthracene doping on the cell performance was discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.525-528
• /
• 1997

In this study, Eu(TTA)$_3$(phen) was synthesized and its films were prepared by vapor deposition method. Its films were characterized by UV-Vis absorption spectroscopy, Atomic Force Microscopy(AFM) and Photoluminescence(PL) measurements. Their electroluminescent(EL) characteristics were investigated by PL measurements, where a cell structure of glass substrate/ITO/Eu(TTA)$_3$(phen)/Al was employed. It was found that its films were well prepared without any decomposition and the film thickness could be controlled by adjusting the amount of Eu(TTA)$_3$(phen) in a boat. The EL spectrum of these films was almost the same as that of PL spectrum of these films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.284-287
• /
• 2000

We analyzed the 3-dimensional discharge characteristic in plasma display panel(PDP) cell using the 3-dimensional emission distribution of 828nm light measured by scanned point detecting method(SPDM). The emitted light distributions on the ITO electrode show the stronger light intensity near to the electrode gap than outside. Also, 828nm light is widely detected outside of the bus electrode. We consider that measurement using new SPDM is effective to analyze the discharge physics and propose the new panel structures.