• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.685-688
• /
• 2009

Surface Texturing is very important process for high cell efficiency in crystalline silicon solar cell. Anisotropic texturing with an alkali etchant was known not to be able to produce uniform surface morphology in multi-crystalline silicon (mc-Si), because of its different etching rate with random crystal orientation. In order to reduce surface reflectance of mc-Si wafer, the general etching tendency was studied with HF/HN$O_3$/De-ionized Water acidic solution. And the surface structures of textured mc-Si in various HF/HN$O_3$ ratios were compared. The surface morphology and reflectance of textured silicon wafers were measured by FE-SEM and UVvisible spectrophotometer, respectively. We obtained average reflectance of $16{\sim}19$% for wavelength between 400 nm and 900 nm depending on different etching conditions.

• 한국지반공학회논문집
• /
• 제20권6호
• /
• pp.75-83
• /
• 2004

본 논문에서는 사질토의 취성적 응력-변형률 관계와 전단시 체적팽창을 고려할 수 있는 구성모델에 대한 연구를 수행하였다. 제안된 모델은 일반등방경화규칙에 의거한 비등방 경화규칙을 적용하였으며, 항복면의 형태는 응력공간에서 원통형으로 나타나는 단순한 형태로 실용적으로 적용하기 편리하도록 하였다. 또한 유동규칙을 단순화하여 구체적인 팽창률 함수를 이용하여 정의하였다. 또한 가상적인 첨두응력비를 정의하여 취성적 응력-변형률 관계를 모델링하는 것이 가능하였다. 이러한 구성모델은 수학적 정식화를 한 후 실험자료와 비교하도록 프로그램을 구현하였다. 동반논문에서는 삼축실험결과와 비교하여 검증할 것이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.292-297
• /
• 2000

In this research, the dynamic photoelastic experimental hybrid method for bimaterial is introduced. Dynamic biaxial loading device is developed, its strain rate is 31.637 s-1 and its maximum impact load is 20 ton. Manufactured methods for model of the dynamic photoelastic experiment for bimaterial are suggested. They are bonding method(bonding material: AW106, PC-1) and molding method. In the bonding method, residual stress is not occurred in the manufactured bimaterial. Crack is propagated along the interface or sometimes deviated from the interface. While in the molding method, residual stress is occurred in the manufactured bimaterial. Crack is always deviated from the interface and propagated in the epoxy region(softer materila). In order to propagate with constant velocity along the interface of bimaterial with arbitrary stiffer material, edge crack should be located along the interface of the acute angle side of the softer material in the bimaterial.

• 융합신호처리학회논문지
• /
• 제11권1호
• /
• pp.26-31
• /
• 2010

방향성 그라디언트 매스크의 크기값을 네 방향 에지 정보에 적용하여 선택된 두 방향의 가중된 합으로 표현하는 새로운 에지기반보간 기법 (Directional edge based interpolation, DEBI)을 제안한다. 네 방향의 그라디언트 정보를 추출하기 위한 등방성 그라디언트 매스크를 소개하고, 영상 보간을 이웃한 후보 영역 중에서 가장 유사한 영역을 선정하며, 선택된 영역만을 이용하여 보간을 실시한다. 보간 방향은 등방성 그라디언트 매스크의 최소 절대값을 나타내는 두 방향만이 이용되고, 그라디언트 매스크의 에지성분 특성에 따라서 영상 보간 방향이 결정된다. 두 방향의 보간값은 그라디언트 값을 가중치로 이용하는 방법으로 주변 간을 단순 평균에 의한 기존의 방법에 비하여, 영상 밝기 변화가 심한 곳과 경계선 영역에서 효과적임을 실험으로 증명하였다.

• 소성∙가공
• /
• 제21권5호
• /
• pp.285-290
• /
• 2012

In spite of progress in predicting ductile failure, the development of a macroscopic yield criterion to describe damage evolution in HCP (hexagonal close-packed) materials remains a challenge. HCP materials display strength differential effects (i.e., different behavior in tension versus compression) in their plastic response due to twinning. Cazacu and Stewart(2009) developed an analytical yield criterion for porous material containing randomly distributed spherical voids in an isotropic, incompressible matrix that shows tension-compression asymmetry. The goal of the calculations in this paper is to investigate the effect of the tension-compression asymmetry on necking induced by void nucleation, evolution and consolidation. In order to investigate the effect of the tension-compression asymmetry of the matrix on necking and fracture initiation, three isotropic materials A, B, and C were examined with different ratios of tension-compression asymmetry. The various types of material had BCC, FCC, and HCP crystal structures, respectively. The ratio between tension and compression in plastic flow significantly influences the fracture shape produced by damage propagation as well as affecting the localized neck.

• Carbon letters
• /
• 제21권
• /
• pp.51-60
• /
• 2017

Isotropic pitch-based fibers produced from coal tar pitch with the melt-blowing method were carbonized at temperatures ranging from 800 to $1600^{\circ}C$ to investigate their crystalline structure and physical properties as a function of the carbonization temperature. The in-plane crystallite size ($L_a$) of the carbonized pitch fiber from X-ray diffraction increased monotonously by increasing the carbonization temperature resulting in a gradual increase in the electrical conductivity from 169 to 3800 S/cm. However, the variation in the $d_{002}$ spacing and stacking height of the crystallite ($L_c$) showed that the structural order perpendicular to the graphene planes got worse in carbonization temperatures from 800 to $1200^{\circ}C$ probably due to randomization through the process of gas evolution; however, structural ordering eventually occurred at around $1400^{\circ}C$. For the carbonized pitch powder without stabilization, structural ordering perpendicular to the graphene planes occurred at around $800-900^{\circ}C$ indicating that oxygen was inserted during the stabilization process. Additionally, the shear stress that occurred during the melt-blowing process might interfere with the crystallization of the CPF.

• Journal of Electrical Engineering and information Science
• /
• 제2권6호
• /
• pp.212-216
• /
• 1997

A new metal tip fabrication process for low voltage operation is reported in this paper. The key element of the fabrication process is that isotropic silicon etching and oxidation process used in silicon tip fabrication is utilized for gate hole size reduction and gate oxide layer. A metal FEA with 625 tips was fabricated in order to demonstrate the validity of the new process and submicron gate apertures were successfully obtained from originally 1.7$\mu\textrm{m}$ diameter mask. The emission current above noise level was observed at the gate bias of 50V. The required gate voltage to obtain the anode current of 0.1${\mu}\textrm{A}$/tip was 74V and the emission current was stable above 2${\mu}\textrm{A}$/tip without any disruption. The local field conversion factor and the emitting area were calculated as 7.981${\times}$10\ulcornercm\ulcorner and 3.2${\times}$10\ulcorner$\textrm{cm}^2$/tip, respectively.

• Steel and Composite Structures
• /
• 제28권1호
• /
• pp.1-11
• /
• 2018

In this paper, local ratcheting behavior of 1045 steel plates with circular cutout was investigated. Experimental tests were carried out by a Zwick/Roell HB 100 servo hydraulic machine. In order to measure the local strain at notch root, a data acquisition system with strain gauge was used. Various notch diameters and distances of strain gauges mounted from the notch root were found influential in the magnitude of local ratcheting strain. It was found that the local maximum principal stress plays a crucial role in increasing the local plastic deformation. Numerical simulation was done by ABAQUS software using nonlinear isotropic/kinematic hardening model. Material parameters of hardening model were attained from several stabilized cycles of flat specimens subjected to symmetric strain cycles. The nonlinear kinematic hardening model along with the Neuber's rule was employed to assess local ratcheting at the notch root of steel plates. The results of the numerical simulations agreed closely with those measured values in this study. Both ratcheting progress and mean stress relaxation occurred simultaneously at the notch root.

• 제어로봇시스템학회논문지
• /
• 제4권3호
• /
• pp.360-371
• /
• 1998

In this paper, output precision characteristics of a planar 6 degree-of-freedom parallel mechanisms are investigated, where the 6 degree-of-freedom mechanism is formed by adding an additional link along with an actuated joint in each serial subchain of the planar 3 degree-of-freedom parallel mechanism. Kinematic analysis for the parallel mechanism is performed, and its first-order kinematic characteristics are examined via kinematic isotropic index, maximum and minimum input-output velocity transmission ratios of the mechanisms. Based on this analysis, two types of planar 6 degrees-of-freedom parallel manipulators are selected. Then, dynamic characteristics of the two selected planar 6 degree-of-freedom parallel mechanisms, via Frobenius norms of inertia matrix and power modeling array, are investigated to compare the magnitudes of required control efforts of both three large actuators and three small actuators when the link lengths of three additional links are changed. It can be concluded from the analysis results that each of these two planar 6 degrees-of-freedom parallel mechanisms has an excellent control-in-the-small characteristics and therefore, it can be very effectively employed as a high-precision macro-micro manipulator when both its link lengths and locations of small and large actuators are properly chosen.

• Structural Engineering and Mechanics
• /
• 제35권3호
• /
• pp.335-348
• /
• 2010

Cutouts are often provided in structural and aircraft components for ventilation, for access, inspection, electric lines and fuel lines or sometimes to lighten the structure. This paper addresses the effects of cutout shape (i.e., circular, square, diamond, elliptical-vertical and elliptical-horizontal) and size on buckling and postbuckling response of quasi-isotropic (i.e., $(+45/-45/0/90)_{2s}$) composite laminate under uni-axial compression. The finite element method is used to carry out the investigation. The formulation is based on first order shear deformation theory and von Karman's assumptions are used to incorporate geometric nonlinearity. The 3-D Tsai-Hill criterion is used to predict the failure of a lamina while the onset of delamination is predicted by the interlaminar failure criterion. It is observed that for the smaller size cutout area there is no significant effect of cutout shape on load-deflection response of the laminate. It is also concluded that the cutout size has substantial influence on the buckling and postbuckling response of the laminate with elliptical-horizontal cutout, while this effect is observed to be the least in case of laminate with elliptical-vertical cutout.