• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1993년도 춘계학술대회논문집; 한국과학연구소, 21 May 1993
• /
• pp.101-106
• /
• 1993

A new rotor control scheme, the isotropic control of anisotropic rotor bearing system in complex state space, is proposed, which utilizes the concepts on the eigenstructure of the isotropic rotor system. Then the control scheme is applied to an active magnetic bearing system and the control performance is investigated in relation to control energy, transient response, and unbalance response. In particular, it is shown that the proposed method is efficient for control of unbalance response.

• Geomechanics and Engineering
• /
• 제21권1호
• /
• pp.11-21
• /
• 2020

The traditional formulations for estimation of bearing capacity in rock mechanics assume a homogeneous and isotropic rock mass. However, it is common that the rock mass consists of different layers of different rock properties or of the same rock matrix with distinct geotechnical quality levels. The bearing capacity of a heterogeneous rock is estimated traditionally through the weighted average. In this paper, the solution of the weighted average is compared to the finite difference method applied to a bilayer rock mass. The influence of different parameters such as the thickness of the layers, the rock type, the uniaxial compressive strength and the overall geotechnical quality of the rock mass on the bearing capacity of a bilayer rock mass is analyzed. A parametric study by finite difference method is carried out to develop a bearing capacity factor in function of the layer thickness and the rock mass quality expressed in terms of the geological strength index, which is presented in a form of a chart. Therefore, this correlation factor allows estimating the bearing capacity of a rock mass that is formed by two layers with distinct GSI, depending on the bearing capacity of the rock mass formed only by the upper layer and considered by that way as homogenous and isotropic rock mass.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.80-87
• /
• 1998

In this study, the effects of residual shaft bow and flexible bearings of a single disk rotor are investigated. The stiffness coefficients of a shaft with initial deflection are different from those of a straight shaft. The stiffness coefficients are calculated using Castigliano theorem considering initial deflections. The stiffness coefficients, which are obtained in this study, are in good agreement with FEM results. The speed which causes zero amplitude is shown to be the square root of the ratio of residual bow amplitude to unbalance eccentricity in the case of rigid bearings and isotropic flexible bearings, but not in anisotropic bearings.

• Steel and Composite Structures
• /
• 제30권1호
• /
• pp.1-12
• /
• 2019

In this research, an efficient mixed mode I/II fracture criterion is developed for fracture investigation of orthotropic materials wherein crack is placed along the fibers. This criterion is developed based on extension of well-known Maximum Tensile Stress (MTS) criterion in conjunction with a novel material model titled as Equivalent Reinforced Isotropic Model (ERIM). In this model, orthotropic material is replaced with an isotropic matrix reinforced with fibers. A comparison between available experimental observations and theoretical estimation implies on capability of developed criterion for predicting both crack propagation direction and fracture instance, wherein the achieved fracture limit curves are also compatible with fracture mechanism of orthotic materials. It is also shown that unlike isotropic materials, fracture toughness of orthotic materials in mode $I(K)_{IC}{\mid})$ cannot be introduced as the maximum load bearing capacity and thus new fracture mechanics property, named here as maximum orthotropic fracture toughness in mode $I(K_{IC}{\mid}^{ortho}_{max})$ is defined. Optimum angle between crack and fiber direction for maximum load bearing in orthotropic materials is also defined.

• 한국추진공학회지
• /
• 제1권1호
• /
• pp.111-121
• /
• 1997

본 연구에서는 탄소/에폭시 복합재료의 기계적 결합부위의 결합강도 예측을 위한 구조해석과 실험을 수행하였다. 복합재료 구조물의 Joint설계에 있어 베어링 파괴는 대단히 중요한 파괴형태 중하나이다. 그래서 본 연구에서는 베어링 파괴를 해석적으로 예측하고 실험적으로 확인하였다. 순수인장 파괴(Net Tension Failure)와 베어링 파괴(Bearing Failure) 실험을 위해서 각각 두 가지 형상의 시편을 선택하였다. 기계적 결합강도 예측에 사용된 방법은 특성길이(Characteristic Length)법과 연관시킨 Yamada-Sun 파괴기준(Failure Criterion)과 Tsai-Hill 최대일 이론이다. 그리고 인장특성길이와 압축특성길이는 실험을 통하여 얻어지며, 특히 압축특성길이 결정은 최근에 착안된 베어링파괴 실험으로부터 결정하였다. 위와 같은 예측 방법을 준등방성(Quasi-Isotropic) Carbon/Epoxy HT245/RS3232에 적용하였다. 연구결과, 이론적인 복합재료 파괴예측이 실험결과와 잘 일치함을 확인할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1997년도 제8회 학술강연회논문집
• /
• pp.269-279
• /
• 1997

본 연구에서는 탄소/에폭시 복합재료의 기계적 결합부의 결합강도 예측을 위한 구조해석과 실험을 수행했다. 복합재료 구조물의 결합부 설계에 있어 베어링파괴는 대단히 중요한 파괴형태 중 하나이다. 그래서 베어링 파괴를 해석적으로 예측하고 실험적으로 확인하였다. 순수인장 파괴(Net Tension Failure)와 베어링 파괴(Bearing Failure) 실험을 위해서 각각 두 가지 형상의 시편을 선택했다. 기계적 결합강도 예측에 사용된 방법은 특성길이(Characteristic Length)법과 연관된 Yamada-Sun 파괴기준(Failure Criterion)과 Tsai-Hill 최대일 이론이다. 그리고 인장특성길이와 압축특성길이는 실험을 통하여 얻어지며, 특히 압축특성길이 결정은 최근에 착안된 베어링파괴 실험으로부터 결정됐다. 위와 같은 예측 방법을 준등방성(Quasi - Isotropic) Carbon Epoxy HT245/RS3232에 적용하였다. 연구결과, 이론적인 복합재료 파괴예측이 실험결과와 잘 일치함을 확인할 수 있다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.948-953
• /
• 2001

Nonlinear dynamic equation of a 4-axis rigid rotor supported by two an-isotropic magnetic bearings is derived via Hamilton's principle. It is transformed to a state-space form for the standard Η$_{\infty}$ control problem. we present a robust Η$_{\infty}$ control design methods of continuous and discrete LMI-based approaches and improve performance using loopshaping.

• Bulletin of the Korean Chemical Society
• /
• 제19권11호
• /
• pp.1179-1184
• /
• 1998

Mesogenic and azo monomers were synthesized and copolymerized to obtain two copolymers composed of methacrylate and itaconate backbone. Glass transition temperatures of the copolymers were found to be slightly higher than ambient temperature. Both the copolymers showed liquid crystalline properties. Trans-cis isomerization in film state was observed under UV-irradiation with a light of 365 nm. Regarding the photochemical phase transition behavior, the transition rate of nematic-to-isotropic state was slightly faster in the methacrylate copolymer during irradiation at 365 nm and the rate of the reverse transition was much faster in itaconate copolymer under thermal effect.

• Structural Engineering and Mechanics
• /
• 제63권3호
• /
• pp.269-280
• /
• 2017

One major concern that has occupied the mind of the designers is a structural failure as result of stress concentration in the geometrical discontinuities. Understanding the effective parameters contribute to stress concentration and proper selection of these parameters enables the designer get to a reliable design. In the analysis of perforated isotropic and orthotropic plates, the effective parameters on stress distribution around holes include load angle, curvature radius of the corner of the hole, hole orientation and fiber angle for orthotropic materials. This present paper tries to examine the possible effects of these parameters on stress analysis of infinite perforated plates with central quasi-square hole applying grey wolf optimizer (GWO) inspired by the particular leadership hierarchy and hunting behavior of grey wolves in nature, and also the present study tries to introduce general optimum parameters in order to achieve the minimum amount of stress concentration around this type of hole on isotropic and orthotropic plates. The advantages of grey wolf optimizer are stout, flexible, simple, and easy to be enforced. The used analytical solution is the expansion of Lekhnitskii's solution method. Lekhnitskii applied this method for the stress analysis of anisotropic plates containing circular and elliptical holes. Finite element numerical solution is employed to examine the results of present analytical solution. Results represent that by selecting the aforementioned parameters properly, fewer amounts of stress could be achieved around the hole leading to an increase in load-bearing capacity of the structure.

• 한국주조공학회지
• /
• 제30권6호
• /
• pp.210-216
• /
• 2010

The aim of this study is to characterize a thixoextruded 7075 Al wrought alloy bar in terms of its isotropic behavior through the optical microscope, mechanical test and electron back scattered diffraction. It is also discussed of the extrudability improvement for 7075 Al wrought alloy by thixoextrusion, with emphasis on controlling thixoextrusion parameters. Hot extrusion shows that the maximum extrusion pressure depends on their characteristics in terms of flow stress and hot workability. In the contrary, thixoextrusion demonstrates that the maximum extrusion pressure is almost uniform regardless of the experimental parameters, such as initial ram speed, die bearing length and thixoextrusion temperature. The hot extruded microstructures become elongated to extrusion direction, while the thixoextruded microstructures are isotropic and homogeneously distributed due to the existence of liquid phase between solid grains during the process. The grain refinement due to dynamic recrystallization during thixoextrusion has been also occurred. Subsequent recrystallization would lead to the strengthening of mechanical properties, as observed in the study. The important point is that the values of tensile, yield strength and elongation of the thixoextruded bar without plastic deformation are similar to those of the hot extruded bar with severe plastic deformation.