• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.445-445
• /
• 2008

The behavior of ion trapping and migration in the yittria-stabilized zirconia pellets following high dose ion beam irradiation have been studied using SEM, EDX, and TGA. The ion beam was irradiated at room and higher temperatures and the differences in their results were interpreted in terms of dynamic annealing effects. The SRIM calculation was also performed to explain the cross sectional SEM image of the electrolytes.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.184-189
• /
• 2001

Continuous photografting/crosslinking of polyethyleneglycol dimethacrylate oligomers onto cotton using a water-soluble benzophenone photoinitiator was investigated. Photografting increased with increasing irradiation dose, oligomer concentration and photoinitiator concentration. Maximum grafting efficiency of DM 400 and 600 were 83% and 79%, respectively. the photografting increased the wrinkle resistance of cotton implying surface crosslinking of cotton. bothsurface crosslinking and bulk crosslinking of cotton were accomplished via dual curing of a mixed formulation containing both a thermally curable component (BTCCA/SHP) and a UV-curable component. The wrinkle resistance of the crosslinked cotton was found to be higher when cured by thermal curing due to the facile post-polymerization of the UV active component. The presence of crosslinks in the dually crosslinked cotton was verified with FT-IR and thermogravimetric analysis.

• 대한핵의학회:학술대회논문집
• /
• 1999.05a
• /
• pp.222-227
• /
• 1999

Re-188 is suitable for endovascular liquid-balloon brachytherapy for the prevention of restenosis after angioplasty. Re-188 was concentrated to 3700 MBq/ml and labeled with DTPA. According to dosimetric calculation, it took 420 seconds using Re-188 solution with concentration of 3700 MBq/ml to irradiate 17.6 Gy to the target at 1 mm from the balloon surface. Software was made to estimate the irradiation time. MIRD calculation with dynamic bladder model yielded the whole body dose of Re-188-DTPA as 0.005 mGy/MBq in case of balloon rupture and release of the whole amount into the blood.

• Radiation Oncology Journal
• /
• v.7 no.1
• /
• pp.81-83
• /
• 1989

This study, involving thirty-two patients with carcinoma of uterine cervix treated by high dose rate intracavitary irradiation using a remotely controlled afterloading system, compares the doss at point A and 8 with the Curie-minutes prescription. A linear least-square regression analysis was used to compare the two sets of date. Correlation coefficients between doses at points A and B and the Ci-min prescription are 0.92 (p<0.001) and 0.90 (p<0.001), respectively, and linear relationship is observed between these two system. The limitation and significance of the comparison of the two approaches to intracavitary dosimetry is discussed.

• 대한방사선방어학회:학술대회논문집
• /
• 2009.04a
• /
• pp.94-95
• /
• 2009

See Full Text

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1570-1574
• /
• 2008

Various mechanical test were conducted on conventional and crosslinked ultra-high molecular weight polyethylene(UHMWPE) all prepared from the same lot of medical grade GUR 1050 for artificial joint. The conventional materials were not irradiated and treated by heating. The cosslinked materials were irradiated with $25kGy{\sim}200kGy$ by gamma-ray andthen annealed or remelted. Gamma-ray irradiation and heat treatment process were found to significantly impact the crystallinity, and hence the mechanical behavior, of the highly crosslinked UHMWPE. The radiation dose and heating conditions were key predictors of the uniaxial yielding, plastic flow, and failure properties of conventional and highly crosslinked UHMWPE. The correlation model from experiments would be the basic information to enhance the were resistance of artificial joint liner.

• Proceedings of the Korea Contents Association Conference
• /
• 2014.11a
• /
• pp.229-230
• /
• 2014

본 연구는 소아백혈병의 치료 방법 중 하나인 조혈모세포이식법의 전처치로서 사용되고 있는 전신방사선조사법에 대하여 선량분포에 대한 연구를 진행한 것으로, MCNPX 프로그램을 이용하여 모의실험을 하였다. 결과 피부선량은 평균 112.43 mGy/min, 심부장기선량은 평균 47.52 mGy/min으로 나타났으며, 조직보상체의 재질과 거리에 따라 다르게 나타나는 경향성을 볼 수 있었으며, 결과를 바탕으로 전신방사선조사를 임하기 전에 정량적인 선량평가를 할 수 있을 것으로 생각된다.

• Journal of Microbiology and Biotechnology
• /
• v.3 no.4
• /
• pp.244-251
• /
• 1993

A novel system has been developed to produce ${\delta}-aminolevulinic$ acid (ALA) using the intact cells of late logarithmic phase of Rhodocyclus gelatinosus KUP-74. The system was shown optimum yield of extracellular ALA under a condition of anaerobic light irradiation (4 Klux) at $30^{\circ}C$ with no variation in cell mass. The rate of extracellular ALA formation was stimulated by low doses of either $C_4\;or\;C_5$ ALA biosynthetic precursors, where 5 mM ($C_4) and 3 mM ($C_5) of each precursors were appeared to generate the maximum rates of 3.3 and 4.0 nmoles of ALA per 0.35 mg cells per hr, respectively. Half-life of the system was 10 hr in a sense of an ability of portage transport of L-glutamate, and sequential dose of this compound was resulted in promising recovery of the ALA.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.108-114
• /
• 2008

Uniaxial tension and compression test were conducted on conventional and crosslinked ultra-high molecular polyethylene (UHMWPE) all prepared from the same lot of medical grade GUR 1050. The conventional materials were unirradiated and gamma irradiated with $25kGy{\sim}200kGy$. Gamma irradiated processing was found to significantly impact the crystallinity, and hence the mechanical behavior, of the highly crosslinked UHMWPE. The crystallinity and radiation dose were key predictors of the uniaxial yielding, hardness, plastic flow, and failure properties of conventional and highly crosslinked UHMWPE. The correlation model from experiments would be the basic information to design the liner of artificial joint.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.197-198
• /
• 2000

A surface-assisted photo-control of the liquid crystal (LC) alignment has been achieved by modifying the topmost surface of the polyimide film with photo-reactive molecules. Recently, photo-alignment technique using a thin film of poly(vinyl cinnamates) have been reported. However their commercial potentiality is limited by their low thermal stability. To enhance thermal stability, we synthesized the chalcone derivatives as the photo-reactive molecules and introduced the materials on the surface-modified polyimide film.. We identified that the photo-chemical reaction of the chalcone derivatives occur in few minutes with irradiation of UV light. The photo-alignment characteristics of the modified polyimide films treated by polarized UV light and their LC cells are investigated as a function of exposure dose.