• Clinical and Experimental Pediatrics
• /
• v.53 no.5
• /
• pp.661-665
• /
• 2010

Anemia caused by vitamin B12 deficiency resulting from inadequate dietary intake is rare in children in the modern era because of improvements in nutritional status. However, such anemia can be caused by decreased ingestion or impaired absorption and/or utilization of vitamin B12. We report the case of an 18-year-old man with short stature, prepubertal sexual maturation, exertional dyspnea, and severe anemia with a hemoglobin level of 3.3 g/dL. He had a history of small bowel resection from 50 cm below the Treitz ligament to 5 cm above the ileocecal valve necessitated by midgut volvulus in the neonatal period. Laboratory tests showed deficiencies of both vitamin B12 and iron. A bone marrow examination revealed dyserythropoiesis and low levels of hemosiderin particles, and a cytogenetic study disclosed a normal karyotype. After treatment with parenteral vitamin B12 and elemental iron, both anemia and growth showed gradual improvement. This is a rare case that presented with short stature and delayed puberty caused by nutritional deficiency anemia in Korea.

• Microbiology and Biotechnology Letters
• /
• v.25 no.6
• /
• pp.552-559
• /
• 1997

Fe (III) impurities in clay could be microbially removed by inhabitant dissimilatory Fe (III) reducing microorganisms. Insoluble Fe (III) in clay particles was leached out as soluble reductive form, Fe (II). The microorganisms removed from 10 to 45% of the initial Fe (III) when each sugar was supplemented to be in ranges of 1 - 5 % (w/w; sugar/clay). The microorganisms reduced 2.1 - 12.8 mol of Fe (III) per 100 mol of carbon in sugars metabolized when sugars such as glucose, maltose, and sucrose were used as sole carbon source. Bacillus sp. IRB-W and Pseudomonas sp. IRB-Y were isolated from the enrichment culture of the clay. The isolates were considered to participate in metabolizing organic compounds to fermentative intermediates with relatively little Fe (III) reduction at initial Fe (III) reduction process. By the microbial treatment, the whiteness of the clay was increased form 63.20 to 79.64, whereas the redness was obviously decreased form 13.47 to 3.55. This treatment did not cause any unfavorable modifications in mineralogical compositions of the clay.

• Journal of Powder Materials
• /
• v.11 no.1
• /
• pp.50-54
• /
• 2004

Nanoparticles of iron oxides have been prepared by the levitational gas condensation (LGC) method, and their structural and magnetic properties were studied by XRD, TEM and Mossbauer spectroscopy. Fe clusters were evaporated from a surface of the levitated liquid Fe droplet and then condensed into nanoparticles of iron oxide with particle size of 14 to 30 nm in a chamber filled with mixtures of Ar and $O_2$ gases. It was found that the phase transition from both $\gamma$-$Fe_2O_3$ and $\alpha$-Fe to $Fe_3O_4$, which was evaluated from the results of Mossbauer spectra, strongly depended on the $O_2$ flow rate. As a result, $\gamma$-$Fe_2O_3$ was synthesized under the $O_2$ flow rate of 0.1$\leq$$Vo_2$(Vmin)$\leq$0.15, whereas $Fe_3O_4$ was synthesized under the $O_2$, flow rate of 0.15$\leq$$Vo_2$(Vmin)$\leq$0.2.

• Journal of the Korean Society of Combustion
• /
• v.16 no.4
• /
• pp.23-30
• /
• 2011

In the iron and steel manufacturing, sintering process precedes blast furnace to prepare feed materials by agglomerating powdered iron ore to form larger particles. There are several techniques which have devised to improve sintering production and productivity including flue gas recirculation(FGR) and additive gas enriched operation. The application of those techniques incurs variations of process configurations as well as inlet and outlet gas conditions such as temperature, composition, and flow rate which exert direct influence on reactions in the bed or the operation of the entire plant. In this study, an approach of sintering bed modeling using flowsheet process simulator was devised in consideration of FGR and the change of incoming and outgoing gas conditions. Results of modeling for both normal and FGR sintering process were compared in terms of outgoing gas temperature, concentration, and moisture distribution pattern as well as incoming gas conditions. It is expected to expand the model for various process configurations with FGR, which may provide the usefulness for design and operation of sintering plant with FGR.

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.393-401
• /
• 1997

Commercial flake graphite cast iron substrate was coated with titanium powder by low pressure plasma spraying and was irradiated with a $CO_2$ laser to produce the wear resistant composite layer. From the experimental results of this study, it was possible to composite TiC particles on the surface layer by direct reaction between carbon existed in the cast iron matrix and titanium with thermal sprayed coating by remelting and alloying them using laser irradiation. The cooling rate of laser remelted cast iron substrate without titanium coating was about $1{\times}10^4$ K/s to $1{\times}10^5$ K/s in the order under the condition used in this study. The microstructure of alloyed layer consisted of three zones, that is, TiC particule crystallized zone (MHV $400{\sim}500$), the mixed zone of TiC particule+ledebulite (MHV $650{\sim}900$) and the ledebulite zone (MHV $500{\sim}700$). TiC particules were crystallized as a typical dendritic morphology. The secondary TiC dendrite arms were grown to the polygonized shape and were necking. And then the separated arms became cubic crystal of TiC at the slowly solidified zone. But in the rapidly solidified zone of fusion boundry, the fine granular TiC particules were grouped like grape.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.44-51
• /
• 2016

The powder core, conventionally fabricated from iron particles coated with insulator, showed large eddy current loss under high frequency, because of small specific resistance. To overcome the eddy current loss, the increase in the specific resistance of powder cores was needed. In this study, copper oxide coating onto electrically conductive iron particles was performed using a planetary ball mill to increase the specific resistance. Coating factors were optimized by the Response surface methodology. The independent variables were the CuO mass fraction, mill revolution number, coating time, ball size, ball mass and sample mass. The response variable was the specific resistance. The optimization of six factors by the fractional factorial design indicated that CuO mass fraction, mill revolution number, and coating time were the key factors. The levels of these three factors were selected by the three-factors full factorial design and steepest ascent method. The steepest ascent method was used to approach the optimum range for maximum specific resistance. The Box-Behnken design was finally used to analyze the response surfaces of the screened factors for further optimization. The results of the Box-Behnken design showed that the CuO mass fraction and mill revolution number were the main factors affecting the efficiency of coating process. As the CuO mass fraction increased, the specific resistance increased. In contrast, the specific resistance increased with decreasing mill revolution number. The process optimization results revealed a high agreement between the experimental and the predicted data ($Adj-R^2=0.944$). The optimized CuO mass fraction, mill revolution number, and coating time were 0.4, 200 rpm, and 15 min, respectively. The measured value of the specific resistance of the coated pellet under the optimized conditions of the maximum specific resistance was $530k{\Omega}{\cdot}cm$.

• Journal of Environmental Health Sciences
• /
• v.36 no.6
• /
• pp.480-495
• /
• 2010

This study evaluated the distribution of the concentrations of nano-particles and heavy metals (08-Pb, Cr, Zn, As, Fe, 09-Pb, Cr, Zn, Cu, Ni, Mn) in Seoul, Chungnam A and Gwangyang from August to December, in 2008 5 times each in the Seoul area, 5 times in and Chungnam A area and from August to November, in 2009 14 times in the Chungnam A area, 8 times in the Gwangyang area. The examined results showed high concentration level from $PM_1$ through $PM_{0.1}$ in all three areas. These results were obtained the concentration of particles by diameter and statistically significant in Stage5 (1.0-0.56 ${\mu}m$) from the result of conducting Kruskal-Wallis H test (p < 0.05). In the case of the heavy metal concentration included in 0.10-0.056 ${\mu}m$, 0.056 ${\mu}m$, the lead concentration of Chungnam Asan area was 6.49 ng/$m^3$ and 9.93 ng/$m^3$, which was higher than 3.05 ng/$m^3$ and 4.22 ng/$m^3$ of Seoul, respectively. The concentration of iron in Seoul was 9.28 ng/$m^3$ and 13.24 ng/$m^3$, that appeared higher than 2.38 ng/$m^3$ and 3.23 ng/$m^3$ of Chungnam A area, respectively. The concentration level was similar to other metals except lead and iron in Chungnam A area and Seoul. From the concentration of heavy metal included in 0.10-0.056 ${\mu}m$, 0.056 ${\mu}m$, the lead concentration of Chungnam A area was 0.31 ng/$m^3$ and 0.12 ng/$m^3$ while Gwangyang was 0.28 ng/$m^3$, 0.06 ng/$m^3$. Thus Chungnam A area showed higher lead concentration than Gwangyang. The manganese concentration of Chungnam A area was 0.12 ng/$m^3$ and 0.03 ng/$m^3$ while Gwangyang was 0.21 ng/$m^3$ and 0.08 ng/$m^3$. Therefore, the concentration of Gwangyang appeared higher than that of Chunnam A area. These two metals showed statistically significant in 0.056 ${\mu}m$ (p < 0.05, p < 0.01). Among the concentration of heavy metal in all regions, the result demonstrated that the order of higher concentration is arsenic > iron > zinc > chrome > lead > nickel > copper > manganese.

• Clean Technology
• /
• v.29 no.2
• /
• pp.118-125
• /
• 2023

Once a site is contaminated with polychlorinated biphenyls (PCBs), serious environmental and human health risks are inevitable. Therefore, innovative but economical in situ remediation technologies must be immediately applied to the contaminated site. Recently, nanoscale zero-valent iron (nano-ZVI) particles have successfully been applied for the dechlorination of various chlorinated organic compounds like TCE, PCE and DDT, and they are considered to be environmentally safe due to the high abundance of iron in the earth's crust. Nano-ZVIs are much more reactive than granular ones, but tend to agglomerate due to their high surface energy and magnetic properties. In order to prevent them from being agglomerated toward larger particles, TiO₂ was used as a support to immobilize the nano-ZVI particles as much as possible. 10wt% ZVI/TiO₂ was prepared by adding NaBH₄ slowly into an FeSO₄/TiO₂ aqueous slurry. In spite of their non-uniformity in size, the nano-ZVI particles were quite successfully dispersed onto the exterior surface of a non-porous TiO₂ powder. The ZVI/TiO₂ was then employed to degrade Aroclor 1242, a kind of PCBs standard, in spiked soil, and its reactivity towards the degradation of Aroclor 1242 was investigated. The fabricated ZVI/TiO₂ degraded Aroclor 1242 in soil quite effectively, but the creation of remaining dechlorinated compounds, possibly high molecular weight hydrocarbons, in the soil was unavoidable.

• Composites Research
• /
• v.21 no.2
• /
• pp.31-35
• /
• 2008

In order to design light weight and high efficient electromagnetic wave absorbing materials, hollow magnetic particles have been introduced in this study. The electroless plating method has been utilized to coat Ni and Fe on the substrates of synthesized polystyrene particles of submicron size. Removing polystyrene particles by heat treatment resulted in hollow structures. Observation by SEM, TEM and EDS confirmed the surface morphology and coating thickness of Ni and Fe. Polymeric composites containing hollow particles were tested in order to compare the electromagnetic properties between Ni coated and Fe costed particles. The composite of 30 wt% Fe hollow particles showed the higher complex permeability than Ni hollow particles or the conventional barium ferrite particles.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.5
• /
• pp.1-10
• /
• 2008

Synthetic mineral microparticles (SMM) is a patented system which has been developed to promote drainage of water and retention of fine particles during papermaking. It is shown in patents that the SMM system can have advantages in both of drainage and retention, compared with montmorillonite (bentonite), which is one of the most popular materials presently used in this kind of application. Turbidity and gravity drainage time were measured using a Britt-Jar test with representative SMM formulations, in order to confirm the efficacy of SMM covering a wide range of compositions and discover effects of some key variables that have the potential to lead to unexpected advantages in terms of the effectiveness of the microparticles, when used in combination with a cationic polyacrylamide treatment of papermaking furnish. An iron silicate showed highest retention performance, as well as suitably fast drainage time relative to other metal silicate and bentonite. Zinc silicate improved retention and drainage. SMM synthesized from aluminum sulfate ($Al_2(SO_4){_3}$) did not show a benefit in retention and drainage, relative to bentonite. SMM synthesized from aluminum chloride ($AlCl_3$) performed better in drainage and retention than bentonite when the Al/Si ratios were 0.76 and 1.00. It was found that when the Al/Si ratio and neutralization are considered, pH variation due to the change of Al/Si ratio can be a key factor to control the size of primary metal silicate particles and the degree of coagulation of the primary particles.