• 한국재료학회지
• /
• 제25권11호
• /
• pp.630-635
• /
• 2015

The fatigue strength of a nickel-base superalloy was studied. Stress-controlled fatigue tests were carried out at $700^{\circ}C$ and 5 Hz using triangular wave forms. In this study, two kinds of testing procedures were adopted. One is the conventional tension-zero fatigue test(R = 0). The other was a procedure in which the maximum stress was held at 1000 MPa and the minimum stress was diverse from zero to 1000 MPa at 24 and $700^{\circ}C$. The results of the fatigue tests at $700^{\circ}C$ indicate that the fracture mechanism changed according to both the mean stress and the stress range. At a higher stress range, ${\gamma}^{\prime}$ precipitates are sheared by a/2<110> dislocation pairs coupled by APB. Therefore, in a large stress range, the deformation occurred by shearing of ${\gamma}^{\prime}$ by a/2<110> dislocations, which brought about crystallographic shear fracture. As the stress range was decreased, the fracture mode gradually changed from crystallographic shear fracture to gradual growth of fatigue cracks. At an intermediate stress range, as it became more difficult for a/2<110> dislocation pairs to shear ${\gamma}^{\prime}$ particles, cracks started to propagate in the matrix, avoiding the harder ${\gamma}^{\prime}$ particles. High mean stress induced creep deformation, that is, ${\gamma}^{\prime}$ particles were sheared by {111}<112> slip systems, which led to the formation of stacking faults in the precipitates. Thus, the change in fracture mechanism brought about the inversion of the S-N curves.

• Journal of Mechanical Science and Technology
• /
• 제20권1호
• /
• pp.13-18
• /
• 2006

Ti-8Ta-3Nb, as a new biomaterial, was prepared by cast and swaging process. Their deformation behavior of Ti-8Ta-3Nb alloy has been characterized on the basis of its flow stress variation obtained from the true strain rate compression testing in the temperature of $700-900^{\circ}C$ and strain rate of $0.001-10\;s^{-1}$. At the strain rates lower than $0.1\;s^{-1}$ and the all temperature ranges which consist of two phase ${\alpha}+{\beta}$ as well as single ${\beta}$ phase fields, the flow curves show a small degree of flow softening behavior. In contrast, the shapes of the flow curves at other strain rates indicate unstable behavior. The shapes of the flow curves were similar in both as-cast and swaged specimen as well as in both ${\alpha}+{\beta}$ phase and ${\beta}$ phase. The flow stress data did not obey the kinetic rate equation over the entire regime of testing but a good fit has been obtained in the intermediate range of temperatures ($750-850^{\circ}C$). In this range, a stress exponent value of about 7.7 in as-cast specimens and about 6.2 in swaged specimens with an apparent activation energy of about 300 kJ/mol and about 206 kJ/mol respectively have been evaluated.

• 한국강구조학회 논문집
• /
• 제16권2호통권69호
• /
• pp.257-265
• /
• 2004

line-type 유한요소법을 이용하여 불균등 단부 모멘트를 받는 보의 비탄성 좌굴 거동에 대하여 연구하였다. 잔류응력은 단순형과 다항식형 모델을 채택하였으며 잔류응력으로 인해 발생하는 단면의 불균등 항복을 고려하였다. 본 연구에서 얻어진 비탄성 횡-비틀림 좌굴에 대한 결과는 강구조편람의 허용응력법에 의한 설계 경우와 비교하였다. 결과적으로, 강구조편람에 의한 설계는 중지간 보에서 중간 브레이싱이 있는 경우나 없는 경우 모두 과설계가 됨을 알 수 있었다.

• 소성∙가공
• /
• 제24권4호
• /
• pp.234-240
• /
• 2015

Multi-pass shape drawing is very important to produce steel profiles in round samples. In the current study, a process design system is developed for a multi-pass shape drawing. In general, the number of passes for a multi-pass shape drawing is 2 to 3 when the reduction ratio, drawing stress, and productivity are considered. Therefore, calculating the drawing stress and designing the intermediated die shapes are very important. In order to calculate the drawing stress, a shape drawing load prediction method is proposed using a general axisymmetric drawing load prediction model. An intermediate die shape design method is proposed using the initial and the final product shapes. Based on this analysis, a process design system is developed for multi-pass shape drawing for steel profiles. The system works with AutoCAD. The system was applied to design a shape drawing of a spline.

• 한국도로학회논문집
• /
• 제18권3호
• /
• pp.21-32
• /
• 2016

PURPOSES : In this paper, the analytical solutions suggested to simulate the behavior of rheological fluids were rigorously re-derived and investigated for fixed conditions to evaluate the applicability for the solutions on a mini-cone slump test of cement paste. The selected solutions with proper boundary conditions can be used as reference solutions to evaluate the performance of numerical simulation approaches, such as the discrete element method. METHODS : The slump, height, and spread radius for the given boundary and yield stress conditions that are determined by five different analytical solutions are compared. RESULTS : The analytical solution based on fluid mechanics for pure shear flow shows similar results to that for intermediate flow at low yield stresses. The fluid mechanics-based analytical solution resulted in a very similar trend to the geometry-based analytical solution. However, it showed a higher slump at high yield stress and lower slump at low yield stress ranges than the geometry-based analytical model. The analytical solution based on the mini-cone geometry was not significantly affected by the yield criteria, such as von Mises and Tresca. CONCLUSIONS : Even though differences among the analytical solutions in terms of slump and spread radius existed, the difference can be considered insignificant when the solutions were used as reference to evaluate the appropriateness of numerical approaches, such as the discrete element method.

• 한국공간정보시스템학회:학술대회논문집
• /
• 한국공간정보시스템학회 2004년도 춘계 학술발표회 논문집 제1권1호(통권1호)
• /
• pp.53-62
• /
• 2004

A single layer latticed dome is one of the most efficient structures because of its low specivic gravity. For easily analyzing of a single layer latticed dome, joint system is assumed to be pin or rigid joint. However, its joint uses ball whose system has intermediate properties of pin and rigid joint. Therefore this study has a grasp of bending rigidity, stress and mechanical properties through experimental and analyzing method of the bolt inserted ball joint. To analyze the stress of bolt and sleeve, this study uses through 3D elastic contact and cubic element, and then the ball and the bolt are perfectly connected for easily analyzing Compared experimental results to F.E.M, each specimen has an error of less than 12 percent. In the results of stress distribution through F.E.M, stress occurs from bottom of bolt to top of sleeve, and most of tension appears on the bolt, also compression occurs from upper parts of the bolt to the sleeve. The assumption of bending stiffness in ball joint is well known that bolt resists only tension and upper sleeve resiss compression. The results of experiment and analysis have $7{\sim}56%$ error, assuring that upper part of bolt occurs of partial compression. In the result of modified assumption have $4{\sim}20%$ error.

• Journal of Nutrition and Health
• /
• 제32권3호
• /
• pp.318-326
• /
• 1999

Apoptotic cell death, characterized by DNA fragmentation and morphological changes, has previously been shown to occur in vascular endothelial cells cultured with hydrogen peroxide. The present study examined the induction of apoptosis by hydrogen peroxide and whether pyruvate, a key glycolytic intermediate and $\alpha$-keto-monocarboxylate, can inhibit the apoptotic effects in bovine pulmonary artery endothelial cells(BPAECs). Culture with 500uM hydrogen peroxide resulted in 30% cell death and induced morphological changes and DNA fragmentation. Cell injury was inhibited by the treatment with pyruvate. Pyruvate(0.1-5.0mM), and cell viability increased in a dose-dependent manner. In the presence of pyruvate(10~20mM), the viability was improved to over 95%. In contrast, treatment with lactate, a reduced form of phyuvate, did not protect against cell death oxidative stress-induced loss of viability and apoptosis was examined with $\alpha$-cyano-3-hydroxycinnarmate(COHC) as a selective mitochondrial monocarboxylate transport blocker. Incubation with COHC(500uM) did not significantly affect cell viability in the presence of hydrogen peroxide. The cytoprotection by pyruvate(3mM)against hydrogen peroxide stress was abolished by COHC. This indicates that the cytoprotection by pyruvate against oxidative stress in endothelial cells is mediated, at least in part, by mitochondrial pyruvate uptake and hence endothelial enerygetics. However, cytosolic mechanisms related, at least in part, by mitochondrial pyruvate uptake and hence endothelial energetics. However, cytosolic mechanisms related to the glutathione system may also contribute. The results suggest that pyruvate has therapeutic potential in the treatment of oxidative stress-induced cytotoxicity associated with increased apoptosis.

• 한국자원식물학회:학술대회논문집
• /
• 한국자원식물학회 2022년도 추계학술대회
• /
• pp.29-29
• /
• 2022

The fast-changing climatic conditions make plants to be vulnerable to many abiotic stresses. Drought stress is one of the limiting factors that affect pepper production in water deficient regions. It affects plant growth and development by altering physiological, morphological, and metabolic processes. Breeding drought tolerant varieties is one of the mitigation strategies to overcome the ever increasing drought disaster. Hence, screening of new drought tolerant pepper genotypes is essential. The current study was aimed to identify new drought tolerant genotypes among the collection of pepper genetic resources. In total, 70 pepper genotypes were screened for drought tolerance after exposure to drought stress condition. The pepper genotypes were classified as highly tolerant, intermediate, or severely sensitive to drought stress based on the phenotypic analysis. Consequently, 13 genotypes significantly exhibited higher recovery rate after drought stress and were classified as highly tolerant. Comparative analysis of morphological and physiological parameters and expression of drought responsive genes between tolerant and susceptible pepper genotypes will be presented and discussed. The identified tolerant genotypes will be useful resources for breeding drought tolerant pepper cultivars.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.623-628
• /
• 2000

In this paper, the behavior for transfer girder of the upper-wall and lower-frame structures was studied by the nonlinear finite element analysis. It was analyzed and compared with the experimental results. Analysis results showed that failure modes were progressed by a initial diagonal crack in the shear span between the edges of the load and intermediate support plate. The nonlinear finite element analysis could predict deformation, principal stress, ultimate load and concrete crack. Also analysis results showed good agreement the test results.

• 대한수학회지
• /
• 제34권1호
• /
• pp.87-118
• /
• 1997

This paper is concerned with a mixed Lagrangian formulation of the wiscous, stationary, incompressible Navier-Stokes equations $$ (1.1) -\nu\Delta u + (u \cdot \nabla)u + \nabla_p = f in \Omega $$ and $$ (1.2) \nubla \cdot u = 0 in \Omega $$ along with inhomogeneous Dirichlet boundary conditions on a portion of the boundary $$ (1.3) u = ^{0 on \Gamma_0 _{g on \Gamma_g, $$ where $\Omega$ is a bounded open domain in $R^d, d = 2 or 3$, or with a boundary $\Gamma = \partial\Omega$, which is composed of two disjoint parts $\Gamma_0$ and $\Gamma_g$.