• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.332-339
• /
• 1995

In this paper, it was investigated the guided field intensity distribution of the channel in the silver & potassium ion-exchange glass-waveguide. The guided field intensity distribution analysis of ion-exchange glass-waveguide was based on the combination of the WKB dispersion relationship method with a Gaussian distribution function of refractive index profile and the Field Shadow method to the modeling of the channel waveguide. As the results of the channel waveguide modeling, it was represented 2-dimensional and 3-dimensional field distribution of ion-exchange glass waveguide.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1789-1798
• /
• 1994

This paper aimed for numerical simulation of complicated gas turbine combustor with swirler. For the convenience of numerical analysis, fuel nozzle and air linear hole areas of secondary and dilution zone, which are issued to jet stream, were simplified to equivalent areas of annular type. In other to solve these problems, imaginary source terms which are corresponded to supplied fuel amount were added to those of governing equation. Chemical equilibrium model of infinite reaction rate and $k-{\epsilon}-g$ model with the consideration of density fluctuation were applied. As the result, swirl intensity contributed to mixing of supplied fuel and air, and to speed up the flame velocity than no swirl condition. Temperature profiles were higher than experimental results at the upstream and lower at the downstream, but total energy balance was accomplished. As these properties showed the similar trend qualitatively, simplified simulation method was worth to apply to complicated combustor for predicting combustion characteristics.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.346-351
• /
• 2003

In this paper, an evaluation method of fracture toughness on interface cracks has been investigated under various mixed-mode conditions of the bonded scarf joints. Two types of the bonded scarf joints with an interface crack were prepared to analyze the stress intensity factors using boundary element method(BEM) and to perform the fracture toughness test. From the results of fracture toughness experiments and BEM analysis, an evaluation method of fracture toughness on interface cracks in the bonded components of dissimilar materials has been proposed and discussed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.1
• /
• pp.77-82
• /
• 2002

It is known that fractal theory has recently been used as a useful in the characterization of surface texture and the understanding of tribological phenomena such as friction wear and lubrication The fractal based method for describing the rubbed surface texture has aroused great interest In this paper the fractal descriptors was applied to rubbed surface of hydraulic driving material with image processing system in order to describe morphology of the rubbed surface The results showed that the fractal dimension can be determined by sum of intensity difference of surface pixel. The two step size to get fractal dimension is similar to surface roughness Ra. Fractal dimensions of the rubbed surfaces increase with an increase of applied load Morphology of the rubbed surface driving in lubricant can be effectively obtained by fractal dimensions.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.79-82
• /
• 2002

Three-dimensional pipe flows with elbows and tees for few different pipe fittings are calculated to estimate the effect of swirling flow on measuring accuracy of orifice flow meter. It is evaluated how the pressure difference across the orifice is dependent on the length of upstream straight pipe in a branch and how swirl intensity, swirl angel and axial velocity distribution affect the measuring error of orifice flowmeter. From the results, it is found that, regardless of flow rate specified in this calculation, the effect of the straight pipe length can be neglected for the lengths larger than thirty diameters although there still remain significant swirl at the orifice

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.763-770
• /
• 1995

Gas flow characteristics within the cylinder is important factors in impoving lean combustion stability. This paper shows the effects of various flow fields generated by a swirl control valve(SCV) on combustion process in a 4-valve spark ignition engine. An impulse swirl/tumble meter was used to elucidation the steady-state flow characteristics, and a rotating grating type LDV was developed to measure the mean velocity and tunbulence intensity in relation to the crank angle. These methodologies were applied to clarify the correlation between gas flow characteristics and combustion stability at a lean air fuel ratio. An analysis of the correlation revealed the gas flow conditions required to optimize a lean-burn system.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.239-247
• /
• 2001

Measured radiative heat fluxes on the furnace exit plane of a heavy duty power boiler of steam output 1650 T/h are discussed. A high-ash pulverized bituminous coal was used. Such measurements are necessary to improve heat fluxes inside a steam boiler furnace was manufactured. An extra small heat radiation sensor was placed in the water cooled head of the probe. The sensor had no direct contact with furnace gases and measured only the radiant energy. There was no exposure to convective heat transfer. With the radiometric probe, one can obtain a spherical indicatrix of radiation intensity as well as hemispherical radiative heat flux incident on any surface passing through a measuring point inside the furnace. Thus, the quantity of radiation energy, passing through the furnace exit plane, to the convective heating surfaces and the quantity of radiation energy going in the opposite direction were measured. A formula for relative radiative heat flux on the furnace exit plane has been proposed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.316-322
• /
• 1998

Super precision working technique and machine tool have been developing continually thanks to advanced electronic field. To obtain good result. it is necessary to investigate surface state in grinding with ${\mu}{\textrm}{m}$ level. There were so many researches to satisfy these demands using non-contact methods through the computer vision. In this study, the texture of working surface was analyzed. cooccurrence matrice was obtained from the surface roughness. Texture parameter was obtained by means of position operator compose of $\theta$. d according to variation of angle direction and distance. As a result, it was found that surface texture was more effected by direction ($\theta$) then distance(d).

• Structural Engineering and Mechanics
• /
• v.52 no.4
• /
• pp.829-841
• /
• 2014

The main purpose of this study is to determine the effect of overlay on the crack propagation. In order to simplify the problem, a cement concrete pavement is modeled as an elastic plate on Winkler foundation. To derive the singular integral equations, the Fourier transform and dislocation density function are used. Lobatto-Chebyshev integration formula, as a numerical method, is used to solve the singular integral equations. The numerical solution of stress intensity factor at the crack tip is derived. In order to examine the effect of overlay for resisting crack propagation, numerical analyses are carried out for a cement concrete pavement with an embedded crack and a concrete pavement with an asphalt overlay. Results show the significant factors that influence the crack propagation.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.3
• /
• pp.182-189
• /
• 2013

In the development process of new naval ships, it is necessary to make the effort of the signature management and reduction of ship infrared(IR) signature to increase the ship survivability(susceptibility). So far the ship's contrast radiant intensity is used as a ship IR signature design criteria during the naval ship design stages. However, nowaday it is in a state of disorder at the basic design stage because of the lack of any related studies and methods. In this study, the IR signature management methods for improving the signature reduction and ship survivability are suggested by the comparison analysis of the advantages and disadvantages of signature management techniques. And also the criteria for the ship signature management are suggested when considering the infrared signature measuring assets and sea trial environments of the Korean peninsula.