• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.247-255
• /
• 2013

In this paper, a soft switching DC-DC converter for AC module type photovoltaic (PV) module integrated converter is proposed. A push-pull converter is suitable for a low voltage PV AC module system because the step-up ratio of a high frequency transformer is high and the number of primary side switches is relatively small. However, the conventional push-pull converters do not have high efficiency because of high switching losses by hard switching and transformer losses (copper and iron losses) by high turns-ratio of the transformer. In the proposed converter, primary side switches are turned on at zero voltage switching (ZCS) condition and turned off at zero current switching (ZVS) condition through parallel resonance between secondary leakage inductance of the transformer and a resonant capacitor. Therefore the proposed push-pull converter decreases the switching loss using soft switching of the primary switches. Also, the turns-ratio of the transformer can be reduced by half using a voltage-doubler of secondary side. The theoretical analysis of the proposed converter is verified by simulation and experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.28 no.1
• /
• pp.39-47
• /
• 2023

This paper applies a structural technique with uniform parallel switch characteristics in gates and power loops to minimize the ringing and current imbalance that occurs when a general discrete package (TO-247)-based power semiconductor device is operated in parallel. Also, this propose a heat sink integrated switching module with heat sink design flexibility and high power density. The developed heat dissipation-integrated switching module verifies the symmetry of the parasitic inductance of the parallel switch through Q3D by ansys and the validity of the structural technique of the parallel switch using the LLC resonant converter experiment operating at a rated capacity of 7.5 kW.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.4
• /
• pp.465-471
• /
• 2014

This paper proposes a new switching algorithm for an active clamp snubber to improve the efficiency of a module integrated converter system. This system uses an active clamp method for the snubber circuit for the efficiency and reliability of the system. However, the active clamp snubber circuit has the disadvantage that system efficiency is decreased by switch operating time because of heat loss in resonance between the snubber capacitor and leakage inductance. To address this, this paper proposes a new switching algorithm. The proposed algorithm is a technique to reduce power consumption by reducing the resonance of the snubber switch operation time. Also, the snubber switch is operated at zero voltage switching by turning on the snubber switch before main switch turn-off. Simulation and experimental results are presented to show the validity of the proposed new active clamp control algorithm.

• Journal of the Microelectronics and Packaging Society
• /
• v.4 no.1
• /
• pp.31-38
• /
• 1997

대용량, 고속정보처리가 요구되는 B-ISDN용 스위칭 모듈은 90년초부터 MCM으로 제작후 사용되어 왔다. 특히 MCM은 Data 처리의 고속성 및 회로의 고집적이 요구되는 ATM, GPS 및 개인휴대 통신 분야에 광범위하게 개발 및 응용되고 있다. 따라서 본논문에 서는 고속, 고집적 ATM 교환기의 Switching Module을 제품의 Low Cost와 다충회로를 간 단하게 구현할수 있는"Diffusion patterning"(이하 DP)공정과 기보유중인 Thin Film 공정으 로 MCM을 구현하였다.CM을 구현하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.710-713
• /
• 2004

The design, simulation, modeling and measurement of a low temperature co-fired ceramic (LTCC) RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a Rx/Tx switching circuit and integrated low pass filter. The low pass filter function was designed to operate in th GSM band. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ nm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1673-1675
• /
• 2004

The design, modeling and measurement of RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a LTCC multi-layer switching circuit and integrated low pass filter. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.431-434
• /
• 2004

The design, simulation, modeling and measurement of a RF switch module for GSM applications were presented in this paper. switch module were simulated by ADS and constructed using a LTCC multi-layer switching circuit and integrated low pass filter, designed to operate in the GSM band. Insertion and return losses at 900 MHz of the low pass filters were designed to lower than 0.3 dB and higher than 12.7 dB respectively. The switch module constructed, contained 10 embedded passives and 3 surface mounted components integrated on $4.6{\times}4.8{\times}1.2$ m volume, 6-layer integrated circuit. The insertion loss of switch module at m MHz were around 11 dB.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.1
• /
• pp.36-44
• /
• 2014

The conventional central photo voltaic inverters have several problems. First, shadow problem in each solar panel, and high DC voltage problem from each panel because of concentration to one central inverter. Therefore, module integrated inverter is proposed to solve these problems. The inverter should be small and cost effective. The cost and size in the inverter depend on the inductor. So the switching frequency should be increased to reduce the inductor and total size, but there is a problem in efficiency because of the losses in turn-on and turn-off. In the paper, the critical conduction mode(CRM) switching method is adopted to reduce the switching loss and interleaving method is proposed to increase the efficiency in Flyback converter. Finally, the validity of the proposed scheme is investigated with simulated and experimental results for a prototype system rated at 200W.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.6
• /
• pp.253-257
• /
• 2011

This study was carried out to solve problems such as radio frequency band depletion, confusion risk, and security loss in existing visible wireless communication systems, and to determine the applicability of next-generation networks. A light-emitting diode (LED) light communication system was implemented with a controlling switching light module using the ATmega16 micro-controller. To solve the existing modulation effect and disturbance in visible light communication, an integrated interface was evaluated with a driving light module and analyzes its reception property. A transmitter/receiver using the ATmel's micro-controller, high-intensity white LED-6 modules, and infrared sensor KSM60WLM and visible sensor TSL250RD were designed. An experiment from the initial value of distance to 2.5 m showed 0.46 V of the voltage loss, and if in long distance, external light interference occurred and light intensity was lost by external impact and thus data had to be modified or reset repeatedly. Additionally, when we used 6 modules through the remote controller's lighting dimming, data could be transmitted up to 1.76 m without any errors during the day and up to 2.29 m at night with around 2~3% communication error. If a special optical filter can reduce as much external light as possible in the integrated interface, the LED for lighting communication systems may be applied in next generation networks.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.5
• /
• pp.185-189
• /
• 2005

This paper focuses on the design for Rx/Tx switch module of GSM(global standard mobile) band, characterization of a miniature, low power and dual-band implementation of the front-end switch module with low-pass filer And the effort to make agreement between the simulated design and the measured data for these solutions takes the place through accumulated design and manufacturing data library. We present the design, modeling and measurement of switch module integrating GSM Rx/Tx switching circuit and LPF(low pass filter) on a LTCC(low temperature co-fired ceramic) substrate. For GSM application, insertion and return loss of the low pass filter designed was less than 0.3 dB which was less than 12.7 dB at 900 MHz. The LTCC switch module contained 10 embedded passives and 3 surface mount components integrated on 4.6$\times$4.8$\times$1.2 mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module measured at 900 MHz was 11 dB. In both of the design approach yielded excellent agreement between measured and simulated results.