• Journal of the Korean Solar Energy Society
• /
• v.25 no.4
• /
• pp.69-76
• /
• 2005

The performance of water-to-water heat pump system coupled with the ground source vertical heat exchanger is presented in this paper. The CAP program of Florida Heat Pump Co. is used to predict the heat pump performances while the EED program calculates the borehole fluid temperature. It is shown that COPH increases with decreasing the temperature of output water for the operation of heating mode and COPR increases with increasing temperature of output water for the operation of cooling mode. The value of specific heat extraction rate must be moderate to insure the reasonable installation cost of borehole system. With $1^{\circ}C$decrease of $T_{wo}$ the average COPH increase is estimated as about $0.06/^{\circ}C$(for $T_{wo}\;=\;45{\sim}60^{\circ}C$ range) while with $1^{\circ}C$ increase of $T_{wo}$ the estimation of COPR increase is about $0.13/^{\circ}C$(for $T_{wo}\;= \;5{\sim}11^{\circ}C$ range) at the specific heat extraction rate of 30W/m.

• Korean Journal of Social Welfare
• /
• v.42
• /
• pp.107-138
• /
• 2000

Today, the public assistance program in Korea is provided mainly for the livelihood protection beneficiary in urban area. The fact that the urban community-centered program is also applied to the livelihood protection beneficiary in rural area brings about some problems in fitness and effectiveness of resource distribution. The purpose of my study is to present my opinion that the public assistance program for the rural community should be put in practice after being fully distinguished from the urban program for the effective distribution of limited social welfare resources to insure the minimum standard of living and seek the self-support contribution which is the purpose of the public assistance program. The subject for this study were livelihood protection beneficiaries living in both rural and urban area. And the study was carried out in this parts: first, the way of life in them, second, the contents of 6 main public assistance programs being carried out. Total number of the livelihood protection beneficiaries are 279 case: 143 case from 15 Dong in 5 cities, and 136 case from 15 Myun in 5 counties. And the social worker who are performing the public assistance programare consisted of 50 case: 25 case from 5 Dong in 5 cities, and 25 case from 5 Myun in 5 counties. This research reach the result that the differentiate performance of the public assistance program in rural community would be an effective device for self-support to be freed from the vicious circle of poverty.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.97-105
• /
• 1999

Orifice flow meters are frequently used for measuring gas flow in gas industry. However, to insure the accuracy of the measurement, a certain length of the meter run at the upstream of the flow meter is required. The objective of this study is to analyze flow measurement errors of the orifice flow meter quantitatively for shorter lengths of the meter runs than those suggested in the standard manuals with variation of diameter ratio( $\beta$ ratio) and flow rate. The test results showed that the flow measurement errors of the orifice meter were inversely proportional to the diameter ratio. In other words, when the diameter ratio is 0.3 and 0.7, the measurement error is $-7.3\%$ and $-3.5\%$, respectively. the main reason of the measurement error is due to the swirl effect from the configuration of the meter run at the upstream of the flow meter. In case the length of the meter run is shorter than that suggested in the standard manuals, the swirl effect is not removed completely and it affects the flow meter's performance. As mentioned above, the less the pipe diameter ratio, the more the flow measurement error. It means that the swirl effect on the orifice meter increases as the $\beta$ ratio decreases.

• KIEAE Journal
• /
• v.11 no.2
• /
• pp.123-130
• /
• 2011

BIM based design methodology requires more information than traditional design methodology in order to insure efficiency throughout the project. BIM based design not only requires all building data in the form of 3D shapes, but also all other relevant data regarding building components. Information is typically grouped in a standard classification system such as by standardized material names. The development of a domestic BIM based standard classification system is yet to be created and deployed in the industry. Each designer is specifying their own building information classification systems which is causing inconsistency in the industry. Therefore BIM based designs, are causing confusion in the industry as each designer follow no guidelines for material standardization classification. The lack of information regarding this in the BIM template will continue to cause confusion about a projects building information data consistently. This study is that of preliminary research to develop a BIM template. First, overseas BIM templates were analyzed regarding BIM standards and documentation. Examination then followed regarding the element and characteristics needed for the development of a BIM template, a suggested hierarchy of elements required for a BIM template were then made. The result of this research is that it will be used to develop a "BIM template prototype", to support the generation of building information data regarding neighborhood facilities.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.429-439
• /
• 2000

The primary purpose of dredging work is to maintain navigational readiness and to increase environmental amenity. Therefore the dredging project, which is composed of excavating, removing, transporting and storing or dumping dredged material, must be carefully managed to insure that dredging works are completed in a cost-effective and environmentally safe method. The most important point in dumping operations is evaluating and decreasing the impacts of dumping works at the dumping area. One of the most effective method for this purpose is using the schematic process composed of the sophisticate plan, precise work and predicting/reducing the impacts based on an numerical model being closely linked with field observation. In this study, a numerical model is used to predict the spatial transport and fate of the effluent discharged from the confined dumping facility(CDF) located at a coastal area. To achive this purpose, numerical models were used for reappearing the tidal current of concerned area. These models were then applied to Mokpo harbpr where capital dredging and maintenance dredging are being conducted simultaneously and the CDF is under construction. In series of model case study, we found that the effluent discharged from CDF was governed by the receiving water condition and outfall geometry, so that limit of near-field was 14∼500 meter down stream and 4∼150 meter in transverse direction. dilution ranged from 1.1 to 8.2 on the cases. Long-term diffusion characteristics was governed by the dilution rate during near-field behavior, ambient conditions and CDF operation modes.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.240-247
• /
• 2009

Wind tunnel test for Electro-Optical Targeting System(EOTS) has been conducted to investigate the aerodynamic characteristics, especially the torque characteristics of the rotating parts to insure the enough actuator power during the actual operation. The influence of EOTS's complex configuration, such as the observation window, has been investigated by comparing with the results of the simplified models made of half sphere and the cylinder. It has been found that the position of the observation window of EOTS has an effect on surface pressure distribution and the torque characteristics of the rotating observation part.

• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.104-113
• /
• 2006

Satellites have provided the impetus for the orderly development of reliability engineering research and analysis because they tend to have complex systems and hence acute problems. They were instrumental in developing mathematical models for reliability, as well as design techniques to permit quantitative specification, prediction and measurement of reliability. Reliability engineering is based on implementing measures which insure an item will perform its mission successfully. The discipline of reliability engineering consists of two fundamental aspects; $(1^{st})$ paying attention to details, and $(2^{nd})$ handling uncertainties. This paper uses some of the basic concepts, formulas and examples of reliability theory in application. This paper emphasizes the practical reliability analysis of a Low Earth Orbit (LEO) Micro-satellite power subsystem. Approaches for specifying and allocating the reliability of each element of the power system so as to meet the overall power system reliability requirements, as well as to give detailed modeling and predicting of equipment/system reliability are introduced. The results are handled and analyzed to form the final reliability results for the satellite power system. The results show that the Electric Power Subsystem (EPS) reliability meets the requirements with quad microcontrollers (MC), two boards working as main and cold redundant while each board contains two MCs in a hot redundant.

• The Korean Journal of Applied Statistics
• /
• v.11 no.2
• /
• pp.269-285
• /
• 1998

One of the most important issues in the area of clinical trial research is the determination of the sample size required to insure a specified power in detecting a real or clinically relevant difference of a stated magnitude. Increasingly, medical journals are requiring authors to provide information on the sample size needed to detect a given difference. We restrict our attention to the designs far comparirng two survival distributions. These are concerned with the survival time which is defined as the interval from a baseline(e.g. randomization) to failure (e.g. death, recurrence of disease). Survival times axe right censored when patients have not foiled by the time of analysis or have been loss to follow-up during the trial. For different types of clinical trials for comparing survival distributions, there have been marry research in sample size determination. We review the existing literature concerning commonly used sample size formulae in the design of randomized clinical trials, and compare the assumption, the power and the sample size calculation of these methods. We also compare by simulation the expected power and observed power of each method under various circumstances. As a result, guidelines in terms of practical usage are provided.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.213-217
• /
• 2008

This paper describes an application of centrifugal compressor optimization system, in which the blade profile of impeller is represented with NURBS(Non-Uniform Rational B-Spline) curve. A commercial CFD(Computational Fluid Dynamics) program named NUMECA fine/turbo was used to evaluate the performance of the whole centrifugal compressor flow passage including impeller and diffuser. The whole optimization design system was integrated based on iSIGHT, a commercial integration and optimization software, which provides a direct application of some optimization algorithms. To insure the practicability of optimization, the performance of centrifugal compressor under all condition was concerned during the optimizing process. That means a compositive object function considering the aerodynamic efficiency, pressure ratio and mass flow rate under different work condition was applied by using different weight number for different conditions. Using the optimization method described in this paper, an optimized design of the impeller blade of centrifugal compressor was obtained. Comparing to the original design, optimized design has a better performance not only under the design work condition, but also the off-design work condition including near stall and near choke condition.

• Journal of Power Electronics
• /
• v.19 no.3
• /
• pp.771-783
• /
• 2019

Due to nonlinear-synthetic uncertainty including the total unknown nonlinear load torque, the total parameter variation and the fixed load torque, a synchronous reluctance motor (SynRM) driving a continuously variable transmission (CVT) system causes a lot of nonlinear effects. Linear control methods make it hard to achieve good control performance. To increase the control performance and reduce the influence of nonlinear time-synthetic uncertainty, an admixed recurrent Gegenbauer orthogonal polynomials neural network (ARGOPNN) with a modified particle swarm optimization (MPSO) control system is proposed to achieve better control performance. The ARGOPNN with a MPSO control system is composed of an observer controller, a recurrent Gegenbauer orthogonal polynomial neural network (RGOPNN) controller and a remunerated controller. To insure the stability of the control system, the RGOPNN controller with an adaptive law and the remunerated controller with a reckoned law are derived according to the Lyapunov stability theorem. In addition, the two learning rates of the weights in the RGOPNN are regulating by using the MPSO algorithm to enhance convergence. Finally, three types of experimental results with comparative studies are presented to confirm the usefulness of the proposed ARGOPNN with a MPSO control system.