• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.283-288
• /
• 1996

This paper presents the development technology of standard shielded resistor divider for full lightning impulse voltage. The ability of large-capacity power apparatus to withstand lighting stroke is usually evaluated by means of full lightning impulse voltage. Lightning impulse voltage test has been essential to evaluate the insulation performance of electrical power apparatus. Recently international standard (IEC 60) on high voltage measurement techniques is being revised and requests a formal traceability of high voltage measurements. Therefore, general interest for this area has grown considerably during last years, and several international intercomparisons have already completed worldwide, i.e. Europe, Japan, America etc., In this viewpoint, we have also investigated the step response of the standard shielded resistor divider, which satisfies the IEC recommendation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.354-357
• /
• 1999

This paper describes on the electrical and physical charateristics thin-film type Pt-RTD\\`s on Si wafers, in which MgO thin-films were used as medium layer in order to improve adhesion of Pt thin-films to SiO$_2$ layer. The MgO medium layer had the properties of improving Pt adhesion to SiO$_2$ and insulation without chemical reaction to Pt thin-films and the resistivity of Pt thin-films was improved. In the analysis of properties of Pt-RTD, TCR value had 3927 ppm/$^{\circ}C$ and liner in the temperature range of room temperature to 40$0^{\circ}C$

• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.660-666
• /
• 1992

Pitchstone reacted with CaO in hot water(9$0^{\circ}C$) and increased its sedimentary volume by forming Ca(OH)2 and calcium silicate hydrates. ALC was prepared from gel at 9$0^{\circ}C$ and subsequently autoclaved at 18$0^{\circ}C$ by using the property of swelling and the physical properties of ALC was investigated with experimental conditions. When the ratio of pitchstone/CaO was 2 (CaO/SiO2 mol ratio=0.81), bulk density, modulus of rupture and thermal conductivity of the ALC were 0.75g/㎤, 73kg/$\textrm{cm}^2$ 0.150 kcal/m.hr.$^{\circ}C$, respectively. The crystalline phase of it was mainly tobermorite. Therefore ALC was turned out to be much lightweighted and good thermal insulation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.531-537
• /
• 2011

This paper proposes a finite element method (FEM)-based model of an interior permanent magnet (IPM) type BLDC motor having stator inter-turn faults. For more realistic simulation studies, the magnetic non-linearity is also considered in proposed model. And the simulation data are verified through experiment. By integrating the developed model with a current-controlled voltage source inverter (CCVSI) model, the characteristics of an inter-turn fault operated by six-switched inverter are investigated considering the speed control. And the circulating current, which is induced by magnetic linkage flux originated from PM, was analyzed from the view point of distortion of air-gap magnetic flux distribution caused deterioration of their torque.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.2000-2004
• /
• 2009

In general, for the condition monitoring of a power transformer using the UHF PD measuring technique, detection of any partial discharge, identifying the defect in the transformer and locating the insulation defect are necessary. In this paper one of the most frequent detects which can result in turn to turn fault in power transformer was examined for identifying the defect. In order to model the defect, as a discharge source, a partial discharge cell was used for experimental activity. Magnitude of electromagnetic wave signals and corresponding amount of apparent discharge were measured simultaneously against phase of applied voltage to the discharge cell. Frequency range and phase resolved partial discharge signals were measured and analyzed. The results will be contributed to build the defect database of power transformer and to decrease the occurrence of transformer faults.

• Journal of the Korean Society of Safety
• /
• v.10 no.3
• /
• pp.62-67
• /
• 1995

The combustion characteristics of cellulose Insulation treated with several metal complexes such as Aluminium hydroxide, Cupric sulfate pentahydrate, Magnesium sulfate heptahydrate, Manganese chloride tetrahydrate and Tnisodium phosphate dodecahydrate are studied to evaluate the effectiveness as a potential flame retardant for cellulosic materials. In this study, we found that LOI values of cellulosic materials treated with the metal complexes are generally increased with the increase of their content. At high concentration, CS(24% ) and SP(24% ) show high LOI values, suggesting resistance to flame spread, The materials examined in this study were found to be relatively more resistance to smouldering and flaming combustion in comparision with untreated cellulosic material. The flammability behavior of the materials exhibits combustion process as follows : LOI$\rightarrow$smouldering region$\rightarrow$smouldering-flaming spread region$\rightarrow$flame spread region.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1997.10a
• /
• pp.70-73
• /
• 1997

This paper describes the technique for detecting failure symptom of mold transformer. This study uses the vibration signal analysis method and FEM as the technique. A loading back method is constructed for experiment, accelation sensors are adhered for measurement of vibration signal. Vibration signal measured by this method is analyzed into variation trend of measurement variables by control of control variables. Magnetic field distribution of molded winding is also acquired by FEM considering the design specfication and the characteristics of insulation material, in conclusion, he relation of results between vibration signal and FEM is studied by these methods.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.81-85
• /
• 2004

This paper describes the testing facility to demonstrate the performance of the distribution class circuit breakers and switchgears and the testing methods. The field-test evaluation system consists of two parts. One is the distribution system for simulation of the condition on interruption mode of switches which are installed in the system and tested by the AFG(Artificial Fault Generator) and the thunderbolt generator just like in the real field. The other is a laboratory for confirmation or the important characteristics regarding to the insulation, gas, environment durability of equipment. For the fatal failure mode, a FMEA(Failure Modes and Effects Analysis) technique which is a kind of a structural analysis to consider a counter-plan was emploved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.595-597
• /
• 2000

Poymeric insulators using in an heavy contamination area are easily attached to contaminants such as salt and by-products of industrial processes. To understand its effect on contaminants adhered to these insulators, we manufactured slurry mixed by some kaolin and salt as artificial contaminated solution. And then put samples in its slurry, for about one minute. And these samples are dried in natural condition for 6 days. We measured the degree of contaminant, AC leakage current for these contaminated samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.402-404
• /
• 2000

The FRP pole had great advantages over other material poles. Light weight, easy installing and transporting were good characteristics. The material's superior properties represented the good durability for sea weather and air pollution, good insulation for electric, and changeable colors. In those properties, usages were like a area affected by sea, downtown, the area among the mountains and a special area for the outstanding views. It was studied that pole manufacturing method, structure analysis of pole by FEM in this study. Filament winding method was selected for a new pole manufacturing method. It produced the tapered poles and mechanically strong properties.