• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.8
• /
• pp.549-555
• /
• 2011

For a $CO_2$ one-stage twin rotary compressor, a T-shaped suction port was used to effectively supply the suction gas stream into two individual suction chambers of the twin cylinders. Suction gas pulsations were observed in the pressure sensor signals and these were simulated by using the acoustic modeling of Helmholz resonators in parallel. The module of acoustic modeling was combined to a computer simulation program for the compressor performance. Validation of the simulation program has been carried out for a bench model compressor in a compressor calorimeter. Cooling capacity and the compressor input power were reasonably well compared between the simulation and the calorimeter test. Particularly, good agreement on P-V diagram between the simulation and the test was obtained.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.2
• /
• pp.167-172
• /
• 2010

EPCIS(EPC Information Service) system is a core component of EPCglobal Architecture Framework offering information of the freights, the time of awareness and the location of awareness on the EPCglobal Network. EPCIS Repository continuously stores and manages mass EPCIS Event input data from a great number of RFID devices simultaneously. The Hybrid DBMS can deal efficiently mass necessary data. This study suggest the plan which can efficiently manage EPCIS Repository using Hybrid DBMS. We offer three schema and stores EPCIS Event data to Altibase DB that can efficiently manage EPCIS Repository using Hybrid DBMS and compare the performance about three schema through simulations.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.49-57
• /
• 2000

In this paper, lumped-element isolator is analyzed and designed using the scattering matrix approach. Using the designed parameters, compact isolator with 7.0x7.0x2.3 mm$^3$ dimensions is fabricated and tested in 1.765GHz PCS phone band. Implemented isolator shows 29.95dB isolation characteristic at center frequency and has 0.35dB insertion loss in overall 30MHz operating bandwidth. Return losses of input and output port are measured below -19 dB. Experimental results show that the implemented isolator has better performances than the conventional one.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.451-454
• /
• 2011

In this paper, a wideband clock generator using novel Automatic frequency calibration(AFC) scheme is proposed. Wideband clock generator using AFC has the advantage of small VCO gain and wide frequency band. The conventional AFC compares whether the feedback frequency is faster or slower then the reference frequency. However, the proposed AFC can detect frequency difference between reference frequency with feedback frequency. So it can be reduced an operation time than conventional methods AFC. Conventional AFC goes to the initial code if the frequency step changed. This AFC, on the other hand, can a prior state code so it can approach a fast operation. In simulation results, the proposed clock generator is designed for DisplayPort using the CMOS ring-VCO. The VCO tuning range is 350MHz, and a VCO frequency is 270MHz. The lock time of clock generator is less then 3us at input reference frequency, 67.5MHz. The phase noise is -109dBC/Hz at 1MHz offset from the center frequency. and power consumption is 10.1mW at 1.8V supply and layout area is $0.384mm^2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.201-207
• /
• 2020

With the expansion in the use of DC power systems and increased need for system maintenance, the development of measurement devices for maintenance requires high stability. Of the different kinds of DC current measurement devices, the single-shot measurement device causes the input signal of the current measuring unit to initially generate a high inrush current. The high inrush current flows into the signal processor of the meter, shortening the life of the internal fuses and causing failure. Therefore, in this study, the I²t value for increasing the durability of the fuse is designed using the available wire diameter. Operating characteristics for 210~400% over-current of the rated current, which is relatively low over-current, are realized by the plating of low melting tin metal. As a result, a method of designing a fuse element for a DC power supply, which improves the safety of the DC current measurement device by blocking the failure caused by the inrush current, is presented.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.657-662
• /
• 2003

Optimum Hamming apodized acousto-optic 2${\times}$2 add/drop multiplexers, using SiO$_2$ film loaded acoustic waveguide with angular offset to the Ti:LiNbO$_3$ waveguide, were fabricated. The four-port device consists of two input waveguides, a polarization beam splitter (PBS), two polarization conversion/acoustooptic tuning waveguide sections, a second PBS and two output waveguides. Insertion loss <7.1 ㏈ has been obtained and side-lobe of -19 ㏈ for -32 ㎽ RF driving power has been realized. Add/drop performance has been confirmed and a linear tuning rate of 8.1 nm/MHz and a 3 ㏈ spectral width of -1.5 nm were demonstrated.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1527-1535
• /
• 2019

Because of the shortcomings of the PID controllers and traditional drive systems of permanent magnet synchronous motors (PMSMs), a PMSM passivity-based control (PBC) drive system based on a quasi-Z source matrix converter (QZMC) is proposed in this paper. The traditional matrix converter is a buck converter with a maximum voltage transmission ratio of only 0.866, which limits the performance of the driven motor. Therefore, in this paper a quasi-Z source circuit is added to the input side of the two-stage matrix converter (TSMC) and its working principle has also been verified. In addition, the controller of the speed loop and current loop in the conventional vector control of a PMSM is a PID controller. The PID controller has the problem since its parameters are difficult to adjust and its anti-interference capability is limited. As a result, a port controlled dissipative Hamiltonian model (PCHD) of a PMSM is established. Thereafter a passivity-based controller based on the interconnection and damping assignment (IDA) of a QZMC-PMSM is designed, and the stability of the equilibrium point is theoretically verified. Simulation and experimental results show that the designed PBC control system of a PMSM based on a QZMC can make the PMSM run stably at the rated speed. In addition, the system has strong robustness, as well as good dynamic and static performances.

• Ocean Systems Engineering
• /
• v.14 no.2
• /
• pp.101-114
• /
• 2024

Seafloor sediment mapping is an essential research topic in shallow coastal waters, especially in port development, benthic habitat mapping, and underwater communications. The seafloor sediments can be interpreted by collecting sediment samples directly in the field using a grab sampler or corer. Another method is optical, especially using underwater cameras and videos. Both methods each have weaknesses in terms of area coverage (mechanic) and accurate positioning (optic). The latest technology used to overcome it is the acoustic method (echosounder) with Global Navigation Satellite System (GNSS) Real Time Kinematic (RTK) positioning. Therefore, in this study will propose the classification of seafloor sediments in coastal waters using acoustic method that is Multibeam Echosounder (MBES) multi-frequency with five frequency (200 kHz, 250 kHz, 300 kHz, 350 kHz, and 400 kHz). In this study, the deep neural network (DNN) used the bathymetric multi frequency, bathymetric difference inters frequencies, and bathymetric features from 5 (five) frequencies as input layer and 4 (four) sediment types in 74 (seventy-four) sample sediment as output layer to make a seafloor sediment map. Results of sediment mapping using the DNN method show an overall accuracy of 71.6% (significant) and a kappa coefficient of 0.59 (moderate). The distribution of seafloor sediment in the study area is mainly silt (41.6%), followed by clayey sand (36.6%), sandy silt (14.2%), and silty sand (7.5%).

• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.1
• /
• pp.146-157
• /
• 2007

Fishing villages have rich potential on account of serving as a base of fishing activities with various maritime ecosystem, culture and maritime resources as well. The object of the study is ports located in Gijang, Busan and it presents the overall development direction in ports within this area. Through systematic and well-planned developing small-sized ports, this research analyzes regional economic implications by improving settlement conditions for fishing villagers scattered around this area taking the ports' natural traits into consideration. The research correlates regional input output analysis by fishing port arrangement project with connection between inter-industries and inter-regions according to the model of input-output analysis and attempts to systematically analyze regional economic structure with the economic implication divided into production, employment and income, influenced upon by the change of political exogenous variable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.5
• /
• pp.947-954
• /
• 2009

This paper proposed a new balanced power amplifier using the reflected input of conventional balanced power amplifiers composed of branch line hybrid coupler. In general, the single-ended amplifier in balanced amplifiers does not have the perfect matching, so the reflected input power, in other words the leakage power, is terminated conventionally at the isolation port of hybrid coupler. However in this work, the leakage power is injected into the auxiliary amplifier, and its output power is combined to the output power of balanced amplifier. Therefore output power, efficiency, and 2-tone IMD3 performances of the proposed balanced amplifier are highly improved compared to the conventional balanced amplifier. For the verification of the proposed balanced amplifier, a conventional balanced amplifier and the proposed balanced amplifier are designed, fabricated and measured, and the measured results are compared. The proposed balanced amplifier shows the improvement in the output power(Pout), power added efficiency (PAE), and 2-tone IMD3 by 3dB, 5.2%, and $5{\sim}10dBc$, respectively, from the measurement.