• Journal of the Korean Statistical Society
• /
• 제5권1호
• /
• pp.35-48
• /
• 1976

Since the solution vector for input-output forecasting models is not directly obtainable, several iterative procedures have been proposed and utilized. As is often the case in numerical analysis, the question of the consistency between the original system and the converged system of the proposed iteration has been ignored, and no one has tried to express the converged solution explicitly. This paper examines this question and points out the inconsistencies between various well-known iterative procedures used to solve input-output models and the original input-output system.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.27-34
• /
• 1995

The analysis of nonlinear equivalent circuit and the resonance characteristics of input current and output voltage were simulated, and their electrical properties are discussed in the transverse-type piezoelectric ceramic transformer. The nonlinear resonance characteristics of input current and output voltage showed by the thermal effect due to a higher driving current, the nonlinearity increased greatly as driving current increased. When load resistor was 100[M.ohm.], the nonlinear coefficient was -1.3. The nonlinear resonance curve of input current and output voltage for a variation of input voltage and load resistor agreed with the discussed theory. The output voltage increased nearly proportioned to input voltage when load resistors were below 50[M.ohm.], the voltage step-up ratio decreased when a load resistor was 100[M.ohm.] and their maximum value was 950.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.125-129
• /
• 1988

This paper proposes a sensitivity technique for analysis of the relationships between input variables (known values) and output variables(unknown values), These design variables are constrained by design equations. Thus, the output variables can be calculated by solving the equations with eliminating the input variables from the equations because the input variables become constants. If the output variables are not satisfied, the values of the input variables must be adjusted by increasing or decreasing the values and then the problem must be solved again. This is called as the iterative design procedure. The sensitivity technique, presented in this paper, gives the sensitivity on the changes of the values of the output variables to the input variables.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1655-1658
• /
• 1991

This paper considers the design and analysis of one-step ahead optimal and adaptive controllers, under the restriction that a known constraint on the input amplitude is imposed. It is assumed that the discrete-time single-input, single-output system to be controlled is linear, except for inequality constraints on the input. The objective function to be minimized is an one-step quadratic function, where polynomial weights on the input and output are included. Both the known parameter and unknown parameter (indirect adaptive controller) cases are examined.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1996년도 추계학술대회논문집
• /
• pp.181-184
• /
• 1996

Fuzzy hierarchical analysis(FHA) has the usefulness to allow decision maker's ambiguities when comparing two alternatives. But, for easiuly appling it to a decision problem, the handling its many data and for decision makers much not knowing fuzzy theory are the obstacles to must be overcomed even if the results of final fuzzy weights can be computed by a personal computer. This paper decribes that FHA is revised, and input/output interfaces are developed to collect input data easily and interprete the fuzzy resultlts. Finally, a fuzzy decision process is suggested with them.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.73-76
• /
• 2009

LCA is nowadays getting popular as a tool to assess the environmental impacts. We can assess the environmental impacts of products and also compare the environmental performance between products with LCA. Furthermore, the LCA results can be used for designing eco-friendly products. But LCA needs an enormous amount of data collection, calculations of energy and material balance. which required to spend pretty much time and cost. However, If we use Input-Output Analysis, There is a lot of advantages that we can save time and cost to calculate and also analyze energy-material balance more comprehensively. Therefore, we implemented the fundamental research of the environmental impact assessment on railway system using life cycle inventory analysis and Input-Output Analysis method.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1619-1626
• /
• 2018

The output power of most facilities for renewable energy generation is unstable due to external environmental conditions. In distributed power systems with two or more sources, a stable output can be achieved with the complementary power supply among the different input sources. In this paper, a double-input DC-DC converter with a wide-input-voltage-range is proposed for renewable energy generation. This converter has the following advantages: the circuit is simple, and the input voltage range is wide and the fault tolerance is excellent. The operation modes and the steady-state analysis are examined. Finally, experimental results are illustrated to verify the correctness of the analysis and the feasibility of the proposed converter.

• 기술혁신연구
• /
• 제22권3호
• /
• pp.1-35
• /
• 2014

본 연구는 기술연관분석으로 단기 상용화를 위한 기술개발과제에 투입된 기술간 융합현황을 분석하였다. 기술연관분석은 산업구조분석의 체계를 기술기획 분야에 적용한 것이다. 본 사례는 기술연관분석을 활용하여 기술과 제품 간 연관도를 중심으로 분석하였으며 분석대상은 중소기업기술정보진흥원의 ' '12년 중소기업 융 복합기술개발사업'에 신청한 401개 과제이다. 분석과정은 다음과 같다. 401개 개별과제에 대해서 투입된 기술은 기술로, 개발과제에서 산출을 제품으로 정의하고 이를 투입과 산출의 행렬로 정리하였다. 투입으로 정의한 기술은 국가과학기술표준분류 상의 소분류를 분류하고, 산출로 정의한 제품은 한국표준산업분류 상의 세세분류로 정의하였다. 즉, 기술을 투입으로, 제품을 산출로 정의하여 기술의 파급도를 분석하였으며 이에 기초하여 기술연관도를 작성하였다 분석결과, IT융합에서는 임베디드 S/W의 기술파급도가 가장 높았으며, ET융합에서는 금형의 기술파급도가 가장 높았고 BT융합은 기능성 화장품 개발기술의 기술파급도가 가장 높았다. 전체적으로 IT융합에서 기술파급도가 높은 요소기술이 많았으며, ET융합에서 기술파급도가 높은 요소기술이 작았다. 따라서 기술파급도가 높은 요소기술에 대한 투자가 융합을 활성화하는 데 중요하며 전체적으로 IT분야가 요소기술의 투자 효과가 높을 것으로 판단한다.

• KIEAE Journal
• /
• 제16권3호
• /
• pp.57-62
• /
• 2016

Purpose: A lot of active researches have addressed the impact of a building on global environment, but most of the researches focus on a residential building and a large office building. Hereupon, this study assessed the impact on environment quantitatively through the analysis of input materials targeting a school building. Method:This study calculated embodied energy of input materials suggested in a construction statement on a school building using the input-output analysis. This study finally carried out environmental impact assessment by applying LCIA DB shown in the preceding researches to the calculated embodied energy. Result: The analysis result revealed that the environmental impact per unit area(/$m^2$) at a school building was $4.11E-02PE{\cdot}yr$, among which Construction was found to be $3.59E-02PE{\cdot}yr$, being analyzed to account for about 87% of the total environmental impact. Also, as a result of detailed environmental impact, the impact on global warming among the total environmental impact was analyzed to be high, accounting for about 76%.

• 신재생에너지
• /
• 제8권1호
• /
• pp.8-17
• /
• 2012

The Korean government pushed ahead various policies to disseminate photovoltaic (PV), wind power, small hydro, bio-fuel, etc. Renewable energy system (RES) budget of the Korean government increased from 118 billion won of 2003 to 876.6 billion won of 2010. The R&D budgetary supports for RES increased by 6.8 times in the period 2003-2010. It is necessary to confirm RES budget expenditure that renewable energy promotion policy makes good performance evaluated in quantity level. This paper made Input-Output Table 2009 contains photovoltaic power generation equipment industry as a dependent sector and analyzed induced production effect by demand of photovoltaic power generation equipment industry. From the empirical analysis result, additional demand in photovoltaic power generation equipment induced 1.932 times of induced production in Korea. Each of industry sector has positive induced production from the additional demand in photovoltaic power generation equipment. Renewable energy promotion in photovoltaic power generation is considered together with industry policy as the option to sustain economic growth.