• 전자공학회논문지
• /
• 제53권7호
• /
• pp.103-109
• /
• 2016

비동기 순차 머신을 위한 교정 제어는 이미 설계된 비동기 순차 머신의 오동작이나 머신에서 발생하는 고장의 영향을 없애는 새로운 제어 기법이다. 본 논문에서는 비동기 순차 머신 교정 제어 시스템의 입력단에서 일어나는 고장을 탐지하고 극복하는 방법을 제안한다. 교정 제어기는 제어 대상 머신의 입력단에서 일어나는 고장을 탐지할 수 있으나 외부 입력단에서 발생하는 고장은 알지 못한다. 이번 연구에서는 비동기 순차 머신을 사용하는 외부 운용자(operator)가 상태 피드백을 받아서 고장을 발견한 후 제어기에게 고장 극복 동작을 명령하는 방식으로 외부 입력단의 고장을 위한 내고장성 제어 기법을 완성한다.

• 한국항공우주학회지
• /
• 제41권4호
• /
• pp.284-290
• /
• 2013

위성의 각속도를 추정하고 반작용 휠의 고장을 검출하기 위하여 비선형 미지입력 관측기를 제안하였다. 위성의 각속도 추정을 위해서 입력 값을 필요로 하는데, 구동기에 고장이 발생하는 경우에 정확한 각속도 추정이 어렵다. 미지입력 관측기는 미지의 고장에 영향을 받지 않으면서 상태추정이 가능하다. 본 논문에서는 SDRE 기법을 적용하여 비선형 미지입력 관측기를 설계하였고, 시뮬레이션을 이용하여 제안한 방법을 검증하였다. 다양한 형태로 동시에 고장이 발생하더라도, 각속도 추정 및 고장 검출이 가능하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.34-36
• /
• 2006

In this paper, we will treat the diagnosis problem to accurately determine fault types. The judgement of fault types is accomplished by observing the cluster newly formed with faults and clustering the input current waveforms to intrinsically show the conditions with the dignet that is a clustering algorithm. The types of input current waveforms are, however, constrained during normal operation, though it considers the load character. In case of faults. new clusters are generated outside the clusters. which appear during normal operation, because the input current waveforms of the induction motor are generated by the type which is not observed in case of faults. The diagnosis about the types of faults is essential to building a fault tree about the induction motor, and it removes the causes of the faults using a fuzzy logic. We, first, constitute a fault tree, which connects with the parts and the entire system of the induction motor, and investigate fault modes which can be generated from the fault tree and the relationship of the cause and the effect of each part (of the motor). Also, we distinguish the faults of each part by means of inducing the said of fuzzy relation equations encapsulating the relationship of the fault modes and each part.

• 문화기술의 융합
• /
• 제6권2호
• /
• pp.467-472
• /
• 2020

일반적인 보통 등급의 지반(ground) 상 구조물의 안정성 확보를 위한 설계입력정수(input-parameters) 도출방법들은 보편적으로 잘 알려져 있다. 연구지역과 같은 습곡된(folded) 변성암(metamorphic rocks) 지반은 엽리가(foliation) 촘촘히 발달해 있고, 엽리에 평행한 소규모 단층들(faults)이 분포하고 있어 설계입력정수 도출을 위한 특별한 조사방법 및 시험, 등이 요구된다. 수 mm 간격의 엽리가 발달한 변성암 지반은 엽리면 직접전단강도시험(direct shear test), 엽리의 배향(strike/dip)과 맵핑(mapping), 엽리의 지하 연속성 파악을 위한 시추조사, 변성암반의 암반분류(rock mass rating), 등이 필요하다. 특정 엽리면을 따라 발달한 소규모의 엽리평행단층(foliation-parallel faults)이 다수 발달한 지반은 선구조선 분석, 단층 추적을 위한 지표지질맵핑, 단층면 직접전단강도시험, 등이 필수적이다. 습곡지반은 지질구조구(structural domain) 분석, 불연속면의 평사투영(stereonet)해석, 습곡축을 따른 전기비저항탐사, 등의 추가조사로 설계입력정수 도출이 합리적이다.

• 대한전자공학회논문지
• /
• 제23권5호
• /
• pp.666-673
• /
• 1986

본 논문에서는 다중고장 검출이 가능하고 부가회로가 적은 새로운 PLA 설계방식을 제안하였다. 부가회로로는 하나의 쉬프트레지스터 열과 2 비트 디코우터에 제어입력을 사용하였다. 제어입력을 사용하므로써 비트선들을 효과적으로 제어할 수 있다. 종래의 논문들에서 구체적으로 다루지 않았던 단락고장과 서로 다른 모델 간의 다중고장을 다루었으며 고장의 등가관계 및 지배고장(Dominant Faults)을 정의하여 다중고장을 해석하였다. 또한 본 설계방식을 Folded PLA에도 적용하였다.

• Journal of Electrical Engineering and Technology
• /
• 제2권4호
• /
• pp.485-493
• /
• 2007

This paper deals with the problem of detection of induction motor incipient faults. Artificial Neural Network (ANN) approach is applied to detect two types of incipient faults (1). Interturn insulation and (2) Bearing wear faults in single-phase induction motor. The experimental data for five measurable parameters (motor intake current, rotor speed, winding temperature, bearing temperature and the noise) is generated in the laboratory on specially designed single-phase induction motor. Initially, the performance is tested with two inputs i.e. motor intake current and rotor speed, later the remaining three input parameters (winding temperature, bearing temperature and the noise) were added sequentially. Depending upon input parameters, the four ANN based fault detectors are developed. The training and testing results of these detectors are illustrated. It is found that the fault detection accuracy is improved with the addition of input parameters.

• 대한전기학회논문지:전력기술부문A
• /
• 제54권2호
• /
• pp.61-66
• /
• 2005

This paper presents a refined protection algorithm of the unfused 22.9kV shunt capacitor banks in grounded wye connection to improve the existing algorithm using the voltage difference method. It is difficult to detect ground faults with arc near the input points or ground faults near the grounding point by the existing algorithm using only the voltage balanced relay. This paper shows that ground faults with arc near the input point can be detected by harmonics analysis of the differential voltage and that it has no impact of harmonics out of nonlinear loads which have the quantitative influence on capacitor banks. Thus the proposed method using harmonics analysis can be a proper detection method. In case of ground faults near the grounding point, an OVGR is being added recently and its validity is verified in this paper. The proposed method is applied to a 22.9kV example system and is verified that the proposed algorithm can detect clearly faults which are not easy to detect by the existing method.

• 전자공학회논문지A
• /
• 제32A권12호
• /
• pp.198-208
• /
• 1995

BiCMOS circuit consist of CMOS part which constructs logic function, and bipolar part which drives output load. Test to detect stuck-open faults in BiCMOS circuit is important, since these faults do sequential behavior and are represented as transition faults. In this paper, proposes a method for efficiently detecting transistor stuck-open faults in BiCMOS circuit by transforming them into slow-to=rise transition and slow-to-fall transition. In proposed method, BiCMOS circuit is transformed into equivalent gate-level circuit by dividing it into pull-up part which make output 1, and pull-down part which make output 0. Stuck-open faults in transistor are modelled as transition fault in input line of gate level circuit which is transformed from given circuit. Faults are detceted by using pull-up part gate level circuit when expected value is '01', or using pull-down part gate level circuit when expected value is '10'. By this method, transistor stuck-open faults in BiCMOS circuit are easily detected using conventional gate level test generation algorithm for transition fault.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권4호
• /
• pp.410-418
• /
• 1999

This paper describes the use of residual and parameter identification methods for fault detection in an air handling unit. Faults can be detected by comparing expected condition with the measured faulty data using residuals. Faults can also be detected by examining unmeasurable parameter changes in a model of a controlled system using a system identification technique. In this study, AutoRegressive Moving Average with seXtrnal input(ARMAX) and AutoRegressive with eXternal input(ARX) models with both single-input/single-input and multi-input/single-input structures are examined. Model parameters are determined using the Kalman filter recursive identification method. Regression equations are calculated from normal experimental data and are used to compute expected operating variables. These approaches are tested using experimental data from a laboratory's variable-air-volume air-handling-unit.

• International Journal of Control, Automation, and Systems
• /
• 제6권3호
• /
• pp.327-338
• /
• 2008

A fault tolerant control system design technique has been proposed and analyzed for managing performance degradation in the presence of multiple faults in actuators. The method is based on a control structure with a model reference reconfigurable control design in an inner loop and command input adjustment in an outer loop. The reduced dynamic performance requirements in the presence of different actuator faults are accounted for through different performance reduced (degraded) reference models. The degraded steady-state performances are governed by the reduced levels of command input. The reconfigurable controller is designed on-line automatically in an explicit model reference control framework so that the dynamics of the closed-loop system follow that of the performance reduced reference model under each fault condition. The reduced command input level is determined to prevent potential actuator saturation. The proposed method has been evaluated and analyzed using an aircraft example against actuator faults subject to constraints on the magnitude and slew-rate of actuators.