• Proceedings of the KSME Conference
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2670-2675
• /
• 2008

We introduce a new type of surface microscope using hydrodynamic phenomena. The fluid flow through the opening of the pipette probe is blocked at short distances between the probe and the surface, thus increasing the pressure loss. Therefore, a scanning flow impedance microscope (SFIM) can image the surface topology by scanning the probe with measuring the pressure loss. The SFIM can display the topology regardless of surface hardness, surface electrical conductivity, and surrounding fluid. The present letter contains the first experimental results on surface topography obtained with this novel microscope. The preliminary results in air demonstrate the lateral resolution of the SFIM is very close to the inner diameter of the probe.

• Korean Journal of Veterinary Service
• /
• 제22권4호
• /
• pp.405-410
• /
• 1999

A 7 month old male shepherd was presented with anorexia, diarrhea, and salivation, and euthanized due to no clinical improvement. Grossly, ulcers were seen on ventral surface of tongue and stomach. The mineralization was obvious in the intercostal space, lung and inner surface of aorta. Kidney was pale, firm and irregular. Histopathology confirmed uremic pneumonitis, end stage kidney and hyperplasia of parathyroid. This case was the typical uremic condition of juvenile dog, which was characterized the diffuse soft tissue mineralization due to hyperparathyroidism secondary to chronic renal failure.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.67-70
• /
• 2003

To develop an effective geometric modeling is essential in order that precise mechanical properties and the geometrical properties of the 3-D braided composites can be estimated. RVE(representative volume element) was adopted fur geometrical modeling. RVE consisted of IC(inner unit cell), ISUC(interior surface unit cell) and ESUC(exterior surface unit cell). The whole geometrical model fur hybrid 3-D braided composites was developed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.141-146
• /
• 2002

The cast iron cylinder liner of the marine engine must be scrapped after its inner surface was definitely worn out due to the friction between the surface and piston ring during the operating. In this research, the restoring method of the worn out cast iron cylinder liner are discussed based on the results of experimental work of the thermal plastic deformation technique.

• Structural Engineering and Mechanics
• /
• 제73권1호
• /
• pp.75-82
• /
• 2020

In this study, the problem of torsion of bars with open cross section surrounded by corrugated boundaries is analyzed. An approximate analytical solution is given using perturbation technique. First, the stress analysis for circular open cross-section for arbitrary opening angle is formulated and the problem is analytically solved. Second, the open cross-section with corrugated cross section is analyzed using perturbation method. First order contributions to the stresses and the torques have been added. The results have been exemplified and compared by considering special examples.

• Journal of Mechanical Science and Technology
• /
• 제16권11호
• /
• pp.1428-1434
• /
• 2002

The ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the effect of initial spacing in surface profiles on wear and scuffing. Three kinds of surface spacing, which are closely related with initial surface micro-cracks on sliding surfaces, were produced on AISI 1045 steel surfaces using different grinding and polishing processes. Frictional forces and time to scuffing were measured, and the shape and amount of wear particles were analyzed to compare the with original surface profiles. From the tests, it was confirmed that the size of wear particles are related closely to the original spacing of the surface profile. The time to failure and amount of wear were sensitive to the surface spacing. The wider surface spacing shows much longer sliding life and smaller amount of wear than the others. Time to scuffing was increased with increasing surface pro(lie spacing. The size of wear particles increased while the wear and wear rate K were decreased with an increase in surface spacing. After the sliding tests, surface cracks of inner parts of the wear track formed due to scuffing were observed and compared among the specimens having the different surface spacing.

• Tribology and Lubricants
• /
• 제17권5호
• /
• pp.399-405
• /
• 2001

In this paper the ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the relation between surface profiles and wear as well as scuffing. Three kinds of surface roughness and asperity radius were produced on AISI 1045 steels using the different processes of grinding and polishing. Frictional forces and time to scuffing were measured. Also, the shape and amount of wear particles were analyzed to compare with original profiles. From the tests, it was confirmed that the size of wear particles are very related to original surface profile. The time to failures and wear amounts were sensitive to the surface spacing. The large surface spacing shows much longer sliding life and smaller wear amount than the others. Time to scuffing was increased with increasing surface profile spacing. The sire of wear particles was increased and the amount was decreased with increasing surface profile spacing. Wear volume and wear rate K were decreased with increasing surface profile spacing. And after sliding tests, surface cracks of inner parts of the wear track occurred scuffing were observed and compared the differences about each specimen having the different surface profile spacing.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.64-71
• /
• 2001

In this paper the ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the relation between surface profiles and wear as well as scuffing. Three kinds of surface roughness and asperity radius were produced on AISI 1045 steels using the different processes of grinding and polishing. Frictional forces and time to scuffing were measured. Also, the shape and amount of wear particles were analyzed to compare with original profiles. From the tests, it was confirmed that the size of wear particles are very related to original surface profile. The time to failures and wear amounts were sensitive to the surface spacing. The large surface spacing shows much longer sliding life and smaller wear amount than the others. Time to scuffing was increased with increasing surface profile spacing. The size of wear particles was increased and the amount was decreased with increasing surface profile spacing. Wear volume and wear rate K were decreased with increasing surface profile spacing. And after sliding tests, surface cracks of inner parts of the wear track occurred scuffing were observed and compared the differences about each specimen having the different surface profile spacing.

• Journal of the Korean Wood Science and Technology
• /
• 제48권2호
• /
• pp.121-135
• /
• 2020

This study aims to evaluate applicability for the continuous drying process using saturated and superheated steam for large-square timber. During drying of the boxed heart square timber, changes in moisture content were examined through the slices of the surface, inner and core layers. The results showed that there was a large moisture content difference between the surface and inner layers during saturated steam drying and between the inner and core layers during superheated steam drying. However, despite the moisture content difference between the layers, no surface check occurred, and an internal check occurred only near the pith or juvenile parts of the wood. The maximum value of the drying stress of the dried larch boxed heart square timber, calculated from the elastic strain of the slice and the tangential elastic modulus of the larch, was 1.30 MPa. The tangential tensile strength of the larch was estimated at 5.21 MPa under temperature and moisture content conditions when drying stress was at a maximum. That is, in the continuous drying process, the saturated and superheated steam did not generate a check in the surface because the drying stress of the wood did not exceed the tangential tensile strength. In further studies, the superheated steam drying conditions will need to be relaxed to suppress the occurrence of internal checks. Such studies would make the continuous drying process using saturated and superheated steam available for the drying of large-square timber.

• Ocean and Polar Research
• /
• 제25권2호
• /
• pp.213-226
• /
• 2003

Kongsfjorden near Korean Arctic Station, Dasan, is a glacial fjord in the Svalbard archipelago, Arctic that is influenced by both Atlantic and Arctic water masses. During the Arctic field season August 2002, surface temperature, salinity, density, and phytoplankton biomass (chi a) was measured in Kongsfjorden. A total of 15 surface samples were collected for the phytoplankton related measurements. Chl a values ranged from 0.08 to 1.4mg chi a $m^{-3}$ (mean of 0.53mg chl a $m^{-3}$) in the overall surface stations. The highest values of the chi a concentrations (> 1.0mg chi a $m^{-3}$) were found near glacier in the northeastern part of Kongsfjorden. Nanoplanktonic (< $20{\mu}m$) phytoflagellates were important contributors for the increase of the chi a. The nano-sized phytoflagellates accounted for more than 90% of the total chi a biomass in the study area. Surface temperatures and salinities ranged from 2.5 to $7.18^{\circ}C$ (mean of $4.65^{\circ}C$) and from 22.55 to 32.97 psu (mean of 30.16 psu), respectively. The physical factors were not highly correlated with phytoplankton distribution. The character of surface water due to down-fjord wind was highly similar to phytoplankton distribution. Drifting ice, freshwater, and semdiment inputs from large tidal glaciers located in the inner part of Konsfjorden create steep physico- and biogeochemical environmental gradients along the length of this ford. The glacial inputs cause reduced biodiversity biomass and productivity in the pelagic community in the inner fjord. Primary production of benthic and pelagic microalgae is reduced due to the limited light levels in the turbid and mixed inner waters. The magnitude of glacial effects diminishes towards the outer fjord. Kongsfjorden is an important feeding ground fer marine mammals and seabirds. Especially, seabirds play the largest energy intake and also export nutrients for primary production of the marine microalgae. Kongsfjorden has received a lot of research attention as a site for exploring the impacts of climate changes. Dasan Station in Kongsfjorden will be an important Arctic site for monitoring and detecting future environmental changes.