• 설비공학논문집
• /
• 제13권12호
• /
• pp.1184-1195
• /
• 2001

Analysis of fluid flow in rectangular ducts has been conducted since it has a wide application. The purpose is to provide experimental data for the comparison with computational results. Velocity distributions inside a rectangular duct with $90^{\circ}$ mitered elbow are measured by 5W laser doppler velocity meter for Reynolds numbers of 4,049, 8,104, and 12,186. Flow rates obtained by the integration of measured velocity profile at three cross-sections, which are inlet, middle section after the elbow, and outlet, have errors less than 0.9% among them. Turbulent fluctuation components in two directions are found to have almost similar magnitude each other at a certain location due to the isotropic characteristic of turbulence.

• 상하수도학회지
• /
• 제23권6호
• /
• pp.799-810
• /
• 2009

With time, the stable management of turbidity is becoming more important in the water treatment process. So optimization of coagulation is important for the improvement of the sedimentation efficiency. we evaluated the mixing and hydrodynamic behavior in the coagulation basin using Computational Fluid Dynamics (CFD). The items for evaluation are a location and the speed of agitator and angle of an injection pipe. The results of the CFD simulation, the efficacy of mixing in the coagulation basin was not affected according to one or two injection pipe and angle of an injection pipe. If there is a agitator near outlet of coagulation basin, the efficacy of mixing don't improve even though the speed of agitator increase. So location of agitator is perfect when it locate center at the inlet stream. The coagulation basin at this study, the proper speed of agitator is form 20rpm to 30rpm.

• Geomechanics and Engineering
• /
• 제15권6호
• /
• pp.1227-1236
• /
• 2018

From all of the environmental problems, blast-induced vibrations often cause concern to surrounding residents. It is often claimed that damage to building superstructures is due to blasting, and sometimes the building owner files a lawsuit against the company that perform blasting operations. The blast-vibration problem has been thoroughly investigated in the past and continues to be the subject of ongoing research. In this study, a tunnel construction has been performed by a construction company, according to their contract they must have used drilling & blasting method for excavation in tunnel inlet and outlet portal. The population is very condensed with almost tunnel below in the vicinity houses of one or two floors, typically built with stone masonry and concrete. This situation forces the company to take extreme precautions when they are designing blasts so that the blast effects, which are mainly vibration and aerial waves, do not disturb their surrounding neighbors. For this purpose, the vibration measurement and analysis have been carried out and a new methodology in minimizing the blast induced ground vibrations at the target location, was also applied. Peak particle velocity and dominant frequencies were taken into consideration in analyzing the blast-induced ground vibration. The methodology aims to employ the most suitable time delays among blast-hole groupings to render destructive interference of surface waves at the target location.

• 대한토목학회논문집
• /
• 제7권3호
• /
• pp.195-202
• /
• 1987

본 연구는 수심이 작은 만곡수호에서 중심각과 저면마찰의 변화에 따른 흐름특성을 분석하기 위하여 만곡부의 중심각이 $30^{\circ}$, $60^{\circ}$, $90^{\circ}$, $120^{\circ}$, $150^{\circ}$, $180^{\circ}$인 수로모형올 선택하였으며, 저면 마찰이 비교적 클 경우(C=30)와 작은 경우(C=60)로 구분하였다. 만곡수로내의 중심각 변화에 따른 수면형, 유속분포 및 유향 등에 관하여 검토하였다. 만곡수로내의 최대수위 발생지점은 중심각에 관계없이 만곡수로 입구로부터 $15^{\circ}$ 하류단면부근의 외측하단에서 발생된다. 저면마찰조건이 최대유속선의 이동경로에 미치는 영향은 만곡수로의 중심각이 약 $150^{\circ}$ 이상인 경우에서 뚜렷하다. 속도수두에 대한 횡방향 수면차의 비는 만곡수로의 중심각이 증가할수록 커지는 경향을 보여 주었다. 중심각에 관계없이 만곡부 시점에서의 유향은 내측으로 종점에서는 외측으로 편기된다.

• 지질공학
• /
• 제13권3호
• /
• pp.281-292
• /
• 2003

모형시추공 내에서 공내수 전기전도도의 자동 측정시스템을 구축하고 이로부터 수리상수 결정과 관련된 제반 기초 환경을 검증하였다. 실험은 상대적으로 높은 염도를 공내수로 하고 증류수를 지층수로 사용하여 지층수의 유입과 유출되는 유량을 일정하게 유지한 상태에서 공내수의 전기전도도 프로파일을 구하는 방식으로 이루어졌다. 관찰의 주 대상은 공내수와 지층수 사이의 염도차. 온도차 및 지층수의 유입량. 유입 ·유출구에 따른 모형시추공 내에서의 전기전도도 변화 양상 파악에 있었다. 실헌결과, 이들 요인이 미치는 영향범위와 적정 측정 환경이 제시되어 향후 모델 실험 및 원위치시험에서 적용될 기초실험 여건이 마련되었다.

• 한국정밀공학회지
• /
• 제32권6호
• /
• pp.571-576
• /
• 2015

Temperature characteristics of supply oil in an ultra-precision hydrostatic table are largely influenced by parameter setting in an oil cooler such as the location of reference sensor and cooling temperature. In this paper, influences of the parameter setting on the temperature variation in the hydrostatic table are experimentally analyzed to suggest the guidelines for practical application. In case of using temperature of inlet oil as a reference sensor in the oil cooler, temperature rise of the supply oil is smaller and thermal settling time is faster than that of using temperature of outlet oil as a reference sensor. The experimental results also show that temperatures of table, rail and return oil can be made almost same, and thermal settling time can be decreased by setting cooling temperature in the oil cooler to be lower than atmospheric temperature.

• Corrosion Science and Technology
• /
• 제8권4호
• /
• pp.153-156
• /
• 2009

The water cooling system for VFD (Variable Frequency Drive) of a fossil fuel power plant was reported to be shut down due to a water leak at the metal connection of the heat-sink to the hoses. In order to identify the cause of the failure, the system was visually inspected, and corrosion products were analyzed with SEM equipped with EDX. The failure was observed repeatedly at the nipples of certain location, suggesting galvanic corrosion. In a U-shaped heat sink with two nipples, for inlet and outlet, only one nipple was corrosively damaged at the tip, while the other was not. Most of the corrosion products were observed at the sound nipple and in the filter, identified as $Cu(OH)_2$. Some other corrosion products, composed of mostly $Cu_2O$, were found at the corrosively attacked nipple. A fair amount of Cl was also detected on the surface of the damaged nipple. It was concluded that galvanic corrosion was occurred due to a current leakage over the whole system, and the damage was accelerated by the accumulated chlorine ions in the cooling water.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.2878-2887
• /
• 2021

As the amount of fission product released from ISLOCA was overestimated because of conservative assumptions in the past, several studies have been recently conducted to evaluate the actual release amount. Among several pathways for the ISLOCA, most studies were focused on the pathway with the highest possibility. However, different ISLOCA pathways may have different fission product release characteristics. In this study, fission product behavior was analyzed for various pathways at the Westinghouse two-loop plant using MELCOR. Four pathways are considered: the pipes from a cold leg, from a downcomer, from a hot leg to the outlet of RHR heat exchanger, and the pipe from the hot leg to the inlet of RHR pump (Pathway 1-4). According to the analysis results, cladding fails at around 2.5 h in Pathways 1 and 2, and on the other hand, about 3.3 h in Pathways 3 and 4 because the ISLOCA pathways affect the safety injection flow path. While the release amount of cesium and iodine ranges between 20 and 26% in Pathways 1 to 3, Pathway 4 allows only 5% to the environment because the break location is submerged. Also, as more than 90% of cesium released to the environment passes through the personnel door, reinforcing the pressure capacity of the doors would be a significant factor in the accident management of the ISLOCA.

• 항공우주시스템공학회지
• /
• 제13권1호
• /
• pp.69-76
• /
• 2019

본 연구에서 복합재료 구조 설계를 위한 수지 이송 성형 공법의 수지 침투 유동 해석을 수행하였다. 대상 복합재료 구조물은 유체 저장 탱크 구조물이다. 유체 저장 탱크 복합재료 구조물 설계를 위해 자연 섬유 복합재료가 적용되었다. 자연섬유 복합재 구조의 제작을 위해 수지 이송 성형 공법을 채택하였다. 탱크의 적절한 RTM 조건을 도출하기 위하여 수지 침투 유동 해석을 수행하였다. 수지 유동 해석은 상용 유한 요소 해석 시뮬레이션 프로그램을 활용하여 수행하였다. 수지 주입구와 배출구의 다양한 변경에 따른 반복적 해석을 수행하여 최적의 수지 주입 시간과 위치를 결정하였다.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.48-56
• /
• 2021

In this study, the heat transfer process around the finned channel tubes is numerically examined. Serially arranged tubes of an evaporator were used for heat exchange. The numerical analysis results confirmed that the vortex generated at the rear of the channel pipe was caused by the fin. Furthermore, it was also confirmed that the temperature difference was large between the inlet and outlet ends of the fin. The temperature of the location where the fin was attached to the channel pipe was found to be close to the surface temperature of the channel wall. However, the temperature rose rapidly closer to the ambient air temperature of 350 K towards the fin end, located at a distance of 0.035 m; it was found to have a significant influence on the heat transfer around the fin-attached channel tube. The wider the vertical flow path, the lower the total heat transfer coefficient. However, the overall heat transfer coefficient increased as the horizontal flow path narrowed. The increment is attributed to an increase in the heat transfer amount due to increased heat transfer surface.