• 지질공학
• /
• 제14권2호
• /
• pp.179-187
• /
• 2004

Frequency Domain Reflectometry(FDR) system과 길이 7cm의 측정센서를 사용하여 에탄을 믹싱리퀴드(EML)를 주입함으로씨 포화된 흙의 유전율상수 변화를 파악하기 위한 실내실험을 실시하였다. 측정센서에 대한 유전율 측정 범위의 확인 및 물과 동일한 비중을 갖는 EML이 포화된 흙의 공극을 통하여 이동 경로를 파악하기 위함이다. EML 확산실험에서는 포화 흙 칼럼 상단부의 배출구가 EML 주입구로부터 이격될수록 포화 흙의 공극을 통한 EML의 확산범위가 확대됨을 확인하였다. 그리고 EML 유동실험의 결과에서는 포화된 흙 칼럼에 대한 주입과 동시에 일정한 간격으로 설치된 모든 측정센서에서 유전율의 변화를 파악하였다. 따라서 EML 주입에 따른 포화 흑의 공극 내에 존재하는 물의 치환이 충분히 가능하며 공극을 통한 이동성도 함께 확인하였다.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.421-428
• /
• 2007

This paper investigates the combustion and emission characteristics of a compression ignition engine fueled with neat and blended Shell's gas-to-liquid (GTL) fuel, which was derived from natural gas through the Fischer-Tropsch process. The experiments were conducted in a 6-cylinder DI diesel engine with pump timing settings of $6^{\circ},\;9^{\circ}\;and\;12^{\circ}$crank angle before TDC over ECE R49 and US 13-mode cycles separately and compared to a conventional diesel fuel. The results show that GTL exhibited almost the same power and torque output, improved fuel economy and effective thermal efficiency. It was found that GTL displayed lower peak in-cylinder combustion pressure and maximum heat release rate (HRR), the timings of the peak pressure and the maximum HRR were generally delayed, and the combustion durations were almost equivalent for diesel and GTL under the same speed-load condition. The results also indicate that, compared to diesel fuel, GTL blends showed a trend forward decreasing four regulated emissions simultaneously and a higher GTL fraction in blends contributing to further reductions in the emissions. In particular and on average, neat GTL significantly reduced HC, CO, NOx and PM by 16.4%, 17.8%, 18.3% and 32.4%, respectively, for all cases.

• 수산해양기술연구
• /
• 제33권1호
• /
• pp.46-58
• /
• 1997

The energy saving is one of the most important factors for profit in marine transportation. In order to reduce the fuel oil consumtion the ship's propulsion efficiency must be increased as possible. The propulsion efficiency depends upon a combination of an engine and a propeller. The propeller has better efficiency as lower rotational speed. This situation led the engine manufacturers to design the engine that has low speed, long stroke and a small number of cylinders. Consequently, the variation of rotational torque became larger than before because of the longer delay-time in fuel oil injection process and an increased output per cylinder. As this new trends the conventional mechanical-hydrualic governors for engine speed control have been replaced by digital speed controllers which adopted the PID control or the optimal control algorithm. But these control algorithms have not enough robustness to suppress the variation of the delay-time and the parameter perturbation. In this paper we consider the delay-time and the perturbation of engine parameters as the modeling uncetainties. Next we design the robust servo controller which has zero offset in steady state engine speed, based on H sub($\infty$) control theory. The validity of the controller was investigated through the response simulation. We used a personal computer and an analog computer as the digital controller and the engine (plant) part respectively. And, we could certify that the designed controller maintains its robust servo performance even though the engine parameters may vary.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제25권3호
• /
• pp.12-22
• /
• 2020

Managed aquifer recharge (MAR) is a promising water management strategy for securing stable water resources to overcome water shortage and water quality deterioration caused by global environmental changes. A MAR demonstration site was selected at Imgok-ri, Sangju-si, Korea, based on screening for the frequency of drought events and local water supply situations. The abundant groundwater discharging from a nearby abandoned coal mine is one of the potential recharge water sources for the MAR implementation. However, it has elevated levels of arsenic (~12 ㎍/L). In this study, the potential of the natural attenuation of arsenic by the field geological media was investigated using batch and column experiments. The adsorption and desorption parameters were obtained for two drill core samples (GM1; 21.8~22.8 m and GM2; 26.0~27.8 m depth) recovered from the potentially water-conducting fracture-zones in the injection well. The effluent arsenic concentrations were monitored during the continuous flow of the mine drainage water through the columns packed with the core samples. GM2 removed about 60% of arsenic in the influent (0.1 mg-As/L) while GM1 removed about 20%. The results suggest that natural attenuation is an acitive process occurring during the MAR operation, potentially lowering the arsenic level in the mine drainage water below the regulatory standard for drinking water. This study hence demonstrates that using the mine drainage water as the recharge water source is a viable option at the MAR demonstration site.

• 간호행정학회지
• /
• 제2권2호
• /
• pp.5-16
• /
• 1996

The purpose of this study is to identify the handwashing knowledge and attitudes of resistered nurses on general wards. Subjects for this study include 182 nurses working in general wards of a hospital in Seoul area. Data were collected by a questionnaire from July 30 to August 10,1996. Statistical analyses were done by the SPSS/PC program. The techniques used in this sudy included frequencies, chi-square test. The results of this study are summarized as follows. 1. 34.6% of the respondents reported that they washed their hand an average of 5 to 7 times during the work day. 2. 38.5% of the respondents reported always washing after each patient contact. Only 9.9% always washed before contact with a patient. 3. 56.6% of the respondents reported a washing time of 10 to 20 seconds, whereas 29.1% washed 21 to 30 seconds. Chi-square tests were employed to determine any differences in handwashing frequency and duration by age, working years, work position. There were no satistically significant differences among the variables. 4. 95.6% of the subjects used water and plain soap during the washing process. The respondents washed the palms of the hands, the backs of their hands and between their fingers(33%). Only 17.6% removed rings before handwashing. Similarly, 11% removed their wristwatch. The majority(96.2%) reported that they used communal textile towel to dry their hands. When asked what method they used to turn off the water faucet after washing, 98.4% reported using direct hand-to-faucet contact. 5. Nursing activities that showed the highest handwashing rates was after wound dressing(22.9%), followed by suctioning(21.4%), injection(21.2%), inserting catheter(18%). 6. Reasons cited for reduced handwashing frequency included being too busy to wash more often(74.7%), no need to wash more often(11.0%) and dry skin caused by frequent handwashing(3.3%). 7. When asked where they obtained their current knowledge of handwashing techniques, they reported professors(73.6%), resisted nurses(14.8%) and supervisor(6.6%). 8. Nursing staff thought that proper handwashing was important factor in decreasing nosocomical infections(72.4%).

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.65-75
• /
• 2016

Aiming at analyzing the power flow of the distribution systems with distribution transformer (DT) branches and PV nodes, a hybrid three-phase power flow methodology is presented in this paper. The incidence formulas among node voltages, loop currents and node current injections have been developed based on node-branch incidence matrix of the distribution network. The method can solve the power flow directly and has higher efficiency. Moreover, the paper provides a modified method to model DT branches by considering winding connections, phase shifting and off-nominal tap ratio, and then DT branches could be seen like one transmission line with the proposed power flow method. To deal with the PV nodes, an improved approach to calculate reactive power increment at each PV node was deduced based on the assumption that the positive-sequence voltage magnitude of PV node is fixed at a given value. Then during calculating the power flow at each iteration, it only needs to update current injection at each PV node with the proposed algorithm. The process is very simple and clear. The results of IEEE 4 nodes and the modified IEEE 34 nodes test feeders verified the correctness and efficiency of the proposed hybrid power flow algorithm.

• 대한지하수환경학회지
• /
• 제6권4호
• /
• pp.159-170
• /
• 1999

초정지역에서 산출되는 탄산수에 대한 수리화학적 연구를 수행하였다. 초정탄산수는 낮은 pH(5.0~5.8). 높은 이산화탄소함량($Pco_2$＜$10^{0.31}$atm). 높은 TDS 함량을 갖는 것으로 특징되며. 화학적으로 Ca-$HCO_3$형에 속한다. 탄산수의 화학적특성은 지하수가 심부로 순환하는 과정에서 심부기원의 이산화탄소와의 반응을 통하여 탄산수가 형성되었음을 지시하며. 낮은 pH를 갖는 탄산수는 물-암석(화강암) 반응이 활발히 진행되면서 지화학적으로 진화된 것으로 판단된다. 또한 높은 $NO_3$함량은 탄산수가 천부로 상승되는 과정에서 주변지하수와 혼합된 특성을 지시한다. 초정 탄산수의 진화과정은 이산화탄소의 공급. 물-암석반응 및 혼합작용으로 설명할 수 있다. 이러한 진화과정을 열역화적으로 확인하고자 지화학 반응을 PHREEQC를 이용하여 모델링하였다. 비록 모델링은 사장석자의 반응에 국한되었지만. 탄산수의 진화과정에서 pH 및 Ca와 Na함량 변화양상에 대한 타당한 설명을 제시하고 있다.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.14-21
• /
• 2008

Synthetic gas is defined as reformed gas from hydrocarbon-based fuel and the major chemical species of the synthetic gas are $H_2$, CO and $N_2$. Among them, hydrogen from synthetic gas is very useful species in chemical process such as combustion. It is a main reason that many studies have been performed to develop an effective reforming device. Furthermore, other technologies have been studied for synthetic gas application, such as the ESGI(Exhaust Synthetic Gas Injection) technology. ESGI injects and burns synthetic gas in the exhaust pipe so that heat from hydrogen combustion helps fast warmup of the close-coupled catalyst and reduction of harmful emissions. However, it is very hard to understand combustion characteristic of hydrogen under low oxygen environment and complicated variation in chemical species in exhaust gas. This study focuses on the characteristics of hydrogen combustion under ESGI operating conditions using a CVC(Constant Volume Chamber). Measurements of pressure variation and flame speed have been performed for various oxygen and hydrogen concentrations. Results have been analyzed to understand ignition and combustion characteristics of hydrogen under lower oxygen conditions. The CVC experiments showed that under lower oxygen concentration, amount of active chemicals in the combustion chamber was a crucial factor to influence hydrogen combustion as well as hydrogen/oxygen ratio. It is also found that increase in volume fraction of oxygen is effective for the fast and stable burning of hydrogen by virtue of increase in flame speed.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.55-59
• /
• 2013

A Light Emitting Diode(LED) is a semiconductor device which converts electricity into light. LEDs are widely used in a field of illumination, LCD(Liquid Crystal Display) backlight, mobile signals because they have several merits, such as low power consumption, long lifetime, high brightness, fast response, environment friendly. In general, LEDs production does die bonding and wire bonding on board, and do silicon and phosphor dispensing to protect LED chip and improve brightness. Then lens molding process is performed using mixed liquid silicon rubber(LSR) by resin and hardener. A mixture of resin and hardener affect the optical characteristics of the LED lens. In this paper, computational design of static mixer was performed for mixing of liquid silicon. To evaluate characteristic of mixing efficiency, finite element model of static mixer was generated, and fluidic analysis was performed according to length of mixing element. Finally, optimal condition of length of mixing element was applied to static mixer from result of fluidic analysis.

• 디자인학연구
• /
• 제19권5호
• /
• pp.223-232
• /
• 2006

본 연구는 기업이라는 조직 변화를 중심으로 한 CI와 BI에 관련된 연구이다. 기업의 조직은 조직의 목표를 달성하기 위해 사회로부터 투입(노동 기술 자원)을 받아 어떤 산출(재화나 서비스)의 형태로 전환시켜 사회로 내보낸다. 이 산출은 그 사회의 일부 목표성취를 위해 사회적 역할을 조직이 담당하고 있는 것을 뜻하는 한편, 사회가 조직의 목표 설정 과정에 영향을 미친다는 것을 시사한다. 이와 반대로 사회는 욕구와 변화를 통하여 기업의 존재, 존속에 직접, 또는 간접의 영향을 주며, 이에 적응하기 위하여 기업은 조직의 형태를 사회의 욕구와 변화에 초점을 맞추게 된다. 이러한 기업의 조직 변화에 따른 CI에서 BI로의 변화 원인과 이론적 근거를 엘빈 토플러의 [적응 기업(The Adaptive Corporation)]을 통하여 제시한 연구이다.