• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.68-77
• /
• 2005

The set-up of an injection molding process is a ye complicated and time-consuming job because it is required to well determine a lot of variables closely related to products. Thus, the productivity of the set-up process mainly depends on operators' expertise and know-how. To solve the problem mentioned before, this research constructs a support system which helps operators determining the condition of the injection molding easily and systematically. The construction of the support system consists of the following four steps: 1) to determine the control variables which affect the target defect types, 2) to design and implement UI(user interface) using a scenario of set-up process, 3) to design and implement the search algorithms for the initial and optima] condition, and 4) to construct the embedded system which integrates the support system with the operating system of a plastic injection molding machine. The test experiments of some typical products are performed using the embedded system to verify the validity of the support system.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1323-1330
• /
• 2000

Recently, injection molding process became more popular than ever to produce large quantities of high precision products or optical products. Especially, optical disk that was made by injection mol ding process has been used for many years as a music play media or computer sub-device. The density of data in disk media has been increased continuously. But those optical disks can cause sensorial problems because of high birefringence or deformation from the residual stresses in the media. Therefore, it is necessary to study the effects of various process conditions on the final bireffingence structure in injection-molded disks for producing precision injection-molded products. In the present paper we have focussed on the effect of holding and compression pressures on the optical anisotropy remaining in the MOD by examining the gapwise distribution of birefringence and extinction angle. The effect of holding pressure was found to form the inner two bireffingence peaks. But the effect of compression pressure on the bireffingence distribution was found to make the uniform distribution near the center in the gapwise direction. Finally, the value of the birefringence near the wall decreased as the mold temperature increased.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.46-51
• /
• 2012

Injection pressure, an important factor in filling process, should be minimized to enhance injection molding quality. Injection pressure can be controlled by valve gate open timing. In this work, we decided the valve gate open timing to minimize the injection pressure. To solve this design problem, we integrated MAPS-3D (Mold Analysis and Plastic Solution-3Dimension), a commercial injection molding CAE tool, to PIAnO (Process Integration, Automation and Optimization), a commercial PIDO (Process Integration, and Design Optimization) tool using the file parsing method. In order to reduce computational cost, we performed an approximate optimization using meta-models that replaced expensive computer simulations. At first, we carried out DOE (Design of Experiments) using OLHD (Optimal Latin Hypercube Design) available in PIAnO. Then, we built Kriging models using the simulation results at the sampling points. Finally, we used micro GA (Genetic Algorithm) available in PIAnO. Using the proposed design approach, the injection pressure has been reduced by 13.7% compared to the initial one. This design result clearly shows the validity of the proposed design approach.

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.1097-1103
• /
• 2010

사출성형에서 사출압력은 제품의 특성을 결정하는 주요인자이므로 성형품의 품질 향상을 위해 사출압력은 최소화 되어야 한다. 또한 휨 변형과 웰드라인은 사출성형에서의 대표적인 불량요인으로 사출성형품의 품질 향상을 위해 방지되어야 한다. 본 논문에서는 사출성형품의 품질 향상을 위해 설계 절차를 2 단계로 나눈다. 첫 번째 설계에서는 공정조건을 제어하여 사출압력과 휨 변형을 최소화 하기 위해 직교배열표를 이용한 전산실험을 수행하고 이를 이용하여 근사모델을 생성한 후 최적설계를 수행한다. 두 번째 설계에서는 유동경로 개선을 통한 웰드라인의 발생을 방지하기 위해 해석모델의 두께를 변경하고 웰드라인 발생 유무를 평가한다. 이러한 설계절차를 통해 사출압력과 휨 변형을 최소화하면서 웰드라인을 방지하여 본 논문에서 제안한 설계방법의 유효성을 보이고자 한다.

• 한국염색가공학회지
• /
• 제34권1호
• /
• pp.46-57
• /
• 2022

In this study, the relationship between fiber orientation and mechanical properties with the injection pressure of polyamide-6/glass fiber composite materials manufactured by the injection molding process was investigated. Also, an actual experimental data and finite element model-based simulation data were analyzed. Specimens were manufactured through the injection molding process setting the injection pressure differently to 700, 800, 900, and 1000 bar, respectively. A morphological analysis and orientation of the PA6/GF composite material were observed using Optical microscope. Through tensile and flexural strength tests, the mechanical properties of the PA6/GF composite materials with the injection pressure were studied. As a result, it was confirmed that the mechanical properties were the superior under the injection pressure of 900 bar molding conditions. In addition, the mechanical properties of the actually manufactured specimen (PA6/GF) and virtual engineering S/W((Digimat, Abaqus) were used to compare and analyze the analysis results for the mechanical properties, and based on the reliable DB, the physical properties of the PA6/GF composite characteristics were studied.

• 소성∙가공
• /
• 제20권1호
• /
• pp.11-16
• /
• 2011

Recently, according to the rapid development of display, many display applications, such as, cellular phone, navigation, monitor and LCD TV have been changed from CRT type to LCD type. BLU(Back Light Unit) is one of main parts in LCD unit and generally, it consists of a light source, a reflective sheet, a LGP(Light Guide Plate), a diffuser sheet, and two prism sheets. The most important component of BLU is a light guide plate, which diffuses the input light to the TFT-LCD module uniformly. The LGP is usually made by injection molding process, and it has numerous optical micro patterns on the surface. In the present study the micro-patterned stamper which has cylindrical shape was fabricated by using the UV-LiGA process. And the replication characteristics have been compared among three different kinds of injection molding process; general injection molding, injection/compression molding and RHCM(Rapid Heating and Cooling Molding). Average replication ratios of CIM and ICM were 19.1% and 64.6%, respectively. On the other hand, the average replication ratio of RHCM process showed the higher value of 98.4% among these. It show that maintaining the mold surface above $T_g$ could increase the replication ratio of micro patterns substantially.

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.124-130
• /
• 2014

In a mass manufacturing system of optical fibers, the sufficient cooling of glass fibers freshly drawn from a draw furnace is essential, asinadequately cooled glass fibers can lead to poor resin coating on the fiber surface and possibly fiber breakage during the process. In order to improve fiber cooling at a high drawing speed, it is common to use a helium injection into a glass fiber cooling unit in spite of the high cost of the helium supply. The present numerical analysis carried out three-dimensional thermo-fluid computations of the cooling gas flow and heat transfer on moving glass fiber to determine the cooling performance of glass fiber cooling depending on the method of helium injection. The results showed that afront injection of helium is most effective compared to a uniform or rear injection for reducing air entrainment into the unit and thus cooling the glass fibers at a high fiber drawing speed. However, above a certain amount of injected helium, there was no more increase of the cooling effect regardless of the helium injection method.

• 한국산학기술학회논문지
• /
• 제5권3호
• /
• pp.218-222
• /
• 2004

본 연구에서는 분리형 이동코어 방식의 스탬퍼 금형을 개발하였고, 사출성형품 품질에 영향을 주는 인자 중에 이동코어 표면 가열 방식이 미세구조를 갖는 성형품 전사성에 미치는 영향에 대해 알아보았다. 이동코어 표면 가열방식은 이동코어를 가열하지 않는 일반사출방식, 할로겐램프를 이용한 복사형 가열방식과 기체화염을 이용해 가열하는 MmSH 방식을 사용했다. COC, PMMA 두 종류의 열가소성 수지를 사용하여 성형품을 제작한 결과, 이동코어 표면온도가 가장 높은 MmSH 방식에서 나노패턴 전사성이 가장 우수했고, 일반사출성형 방식으로 제작한 성형품에서 전사성이 가장 저조했다.

• Structural Engineering and Mechanics
• /
• 제59권1호
• /
• pp.37-57
• /
• 2016

Reservoir geomechanics can play an important role in hydrocarbon recovery mechanism. In $CO_2$-EOR process, reservoir geomechanics analysis is concerned with the simultaneous study of fluid flow and the mechanical response of the reservoir under $CO_2$ injection. Accurate prediction of geomechanical effects during $CO_2$ injection will assist in modeling the Carbon dioxide recovery process and making a better design of process and production equipment. This paper deals with the implementation of a program (FORTRAN 90 interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators, using a partial coupling algorithm. A geomechanics reservoir partially coupled approach is presented that allows to iteratively take the impact of geomechanics into account in the fluid flow calculations and therefore performs a better prediction of the process. The proposed approach is illustrated on a realistic field case. The reservoir geomechanics coupled models show that in the case of lower maximum bottom hole injection pressure, the cumulative oil production is more than other scenarios. Moreover at the high injection pressures, the production rates will not change with the injection bottom hole pressure variations. Also the FEM analysis of the reservoir showed that at $CO_2$ injection pressure of 11000 Psi the plastic strain has been occurred in the some parts of the reservoir and the related stress path show a critical behavior.

• 한국정밀공학회지
• /
• 제31권7호
• /
• pp.591-596
• /
• 2014

Augmented reality is a novel human-machine interaction that overlays virtual computer-generated information on a real world environment. It has found good potential applications in many fields, such as training, surgery, entertainment, maintenance, assembly, product design and other manufacturing operations. In this study, a smartphone-based augmented reality system was developed for the purpose of monitoring and managing injection molding production lines. Required management items were drawn from a management content analysis, and then the items were divided into two broad management categories: line management and equipment management. Effective work management was enabled by providing those working on the shop floor with management content information combined with the actual images of an injection molding production line through augmented reality.