• Advances in materials Research
• /
• v.3 no.2
• /
• pp.91-103
• /
• 2014

A study that demonstrates how to investigate the molded part quality and the consistency of injection process based on the rheological concept is proposed. It is important for plastic material whose melt viscosity is variable with respect to the processing condition. The formulations to couple the melt viscosity with injection pressure and fill time are derived first. Taking calculations of the measured pressure and the time by using these formulations, the melt viscosity in injection process can be determined on machine. As the relation between the injection speed and the melt viscosity is constructed, the influences of the setting parameter of injection machine on the molded part quality can be investigated through evaluating the state of the melt viscosity. In addition, a pressure sensor bushing (PSB) designed with a quick installation feature is also provided and validated. The results show that a higher injection speed improves the tensile strength of the molded part but also the consistency of the molded part quality. This work provides an alternative to evaluate the molding quality scientifically.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.621-626
• /
• 2001

Microcellular foaming process was developed at MIT in 1980's to save a quantity of raw materials and improve mechanical properties. There are many process variables in appling microcellular foaming process to the conventional injection molding process. Of all process variables, part dimension control and shrinkage are the most influential on the post molded dimension. The post molding dimensional change of thermoplastic resins is important to tool designers for predicting the specific difference of molded part vs. actual mold cavity. Generally, articles injection molded are smaller in size than the cavity; hence, the term shrinkage factor is used to define the allowance a designer specifies. It is important to consider the factors that influence molded part dimension. According to ASTM Designation: D 955, shrinkage from mold dimensions of molded plastics was measured. In injection molding, the difference between the dimensions of the mold and of the molded article produced therein from a given material may vary according to the design and operation of the mold. In this paper, shrinkage data of molded plastic parts was obtained. It can be an important information for designing optimum mold system in a microcellular foaming injection molding process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.58-64
• /
• 2004

The shrinkages of injection molded parts are different in molding operational conditions, resins and additives. The shrinkage of injection molded part for crystalline polymer, PBT (polybutylene terephthalate) has been studied for various operational conditions of injection molding and content of additives. Mica was used as a additive to PBT to examine the part shrinkage according to the mica content. The part shrinkages of mica contained PBT decreased as mica content increases. Higher injection temperature and injection pressure resulted in a lower shrinkage. As mold temperature increases the part shrinkage decreased. The part shrinkage of flow direction was less than that of the perpendicular direction to the flow for both pure and mica contained PBT. However the shrinkage difference between flow and perpendicular to flow directions decreased as mica content increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.

• Elastomers and Composites
• /
• v.39 no.3
• /
• pp.193-208
• /
• 2004

Morphology of injection molded polymer blend was investigated by experimental and theoretical approach. In experiments, the effects of injection speed and injection temperature on the morphology of injection molded MPPO/Nylon 6 blend were investigated. The morphology distribution across the part thickness was clearly observed in injection molded blend. We could observe several distinct regions across the thickness of molded part: skin layer, subskin layer and core region. The skin layer where the dispersed phase is fine and highly deformed to the flow direction is observed to be located near the part surface. The subskin layer located at inner region of the skin layer also observed. In the subskin layer, the dispersed phase is coarser than that of skin layer and deforms to the flow direction. Based on the experimental results, the calculation scheme to predict the morphology of injection molded polymer blend was suggested. The morphology of injection molded polymer blend could be predicted in corporation with the result of flow analysis obtained from commercial software for injection molding process and the theory of drop behavior under the flow. The suggested calculation scheme could predict the effect of injection conditions on the morphology of injection molded parts.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.300-305
• /
• 2013

Part shrinkage in injection molding is inevitable phenomenon. Thus, it is necessary not only study on the reducing part shrinkage but characterization of part shrinkage. In this study, part shrinkage in injection molded 2.5 dimensional annular shaped specimens has been studied using glass fiber reinforced PC. Annular shaped specimens were designed with various sizes of outer diameter and thickness. Injection temperature, packing time and packing pressure were selected for operational conditions. Profile variations of outer and inner diameters of molded specimens for various operational conditions were investigated. Sizes of outer and inner diameters of injection molded specimens were smaller than the sizes of mold. Part shrinkage decreased as outer diameter and thickness increased. Part shrinkage showed anisotropic behavior and it depended upon gate location. Subsequently, molded specimens were not circular but oval in shape, and showed the largest shrinkage in the direction of gate. It was realized that the mold design such as gate design is important to control the shape of molded products.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.441-444
• /
• 2009

Weldlines are generated during the injection molding process when two or more melt flows are brought into contact. At the welded contact region, a 'V'-shaped notch is formed on the surface of the molded part. This 'V'-notch deteriorates not only surface appearance but also mechanical strength of the molded part. To eliminate or reduce weldlines so as to improve the weldline strength, the mold temperature at the corresponding weld locations should be maintained higher than the glass transition temperature of the resin material. The present study implements high-frequency induction heating in order to rapidly raise mold surface temperature without a significant increase in cycle time. This induction heating enables to local mold heating so as to eliminate or reduce weldlines in an injection-molded plastic part. The effect of induction heating conditions on the weldline strength and surface appearance of an injection-molded part is investigated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.92-97
• /
• 2012

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameter and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced the shrinkage of injection molded part.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.363-370
• /
• 2003

Shrinkage of injection molded parts is different form operational conditions of injection molding such as injection temperature, injection pressure and mold temperature, and mold design such as gate size. It is also various for different resins which have crystalline structure or not. In this study part shrinkage was investigated for various operational condition and resins; PBT for crystalline polymer, and PC and PMMA for amorphous polymer was used in experiment. Crystalline polymer shows higher part shrinkage by about three times than amorphous polymer. Part shrinkage increased as injection temperature and mold temperature increased and injection pressure decreased. Part shrinkage decreased as gate size increased since the pressure delivery is mush easier for large gate size. Part shrinkage according to the gate location was that the position in the part with close to the gate showed large shrinkage and this phenomenon might be occurred by residual stress.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.165-169
• /
• 2008

The effect of processing conditions on the morphology of polyphenyleneoxide (PPO)/polyamide 6 (PA 6) blends were investigated. Injection molded part with a $15cm{\times}15cm{\times}3.2mm$ sized plate was molded with various injection molding conditions, and the morphology of the injection molded blends was investigation by using SEM. As a result, we found that molded part shows very complicated morphology because it has experienced complex thermal, shear and elongation history during the processing.