• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.491-495
• /
• 2004

The industries use polymer materials for many purposes for they have many merits. The costs of these materials take up too great a proportion of the overall cost of products that use these materials as their major material. It is advantage for polymer industries to reduce these costs. The microcellular foaming process was developed in the early 1980s to solve this problem and proved to be quite successful. Microcellular foaming process uses inert gases such as $CO_2$, $N_2$. As these gases solve into polymer matrices, many properties are changed. The microcellular foaming process makes the glass transition temperature of polymers to low, and diminish the residual stress of polymer matrices. Besides, the microcellular foaming process has several merits, impact strength elevation, thermal insulation, noise insulation, and raw material saving etc. This characteristic of microcellular foaming process has influenced by cell morphology. The cell morphology means cell size and cell density. The cell morphology has influenced by many factors. The examples of factor are pressure drop rate, foaming temperature, foaming time, saturation pressure, saturation time etc. Among their factors, pressure drop rate is the most important factor for cell morphology in microcellular foaming injection molding process. This paper describes about the cell morphology change in accordance with the pressure drop rate of microcellular foaming injection molding process.

• 대한기계학회논문집A
• /
• 제33권3호
• /
• pp.201-209
• /
• 2009

The objective of present research work is to design the heat conductive mould to improve cooling characteristics of the injection mould for a mouse. In order to obtain the high cooling rate of the mould, a heat conductive mould with three different materials was designed. The materials of the base structure, the mid-layer and the molding part of the heat conductive mould were chosen as Cu-Ni alloy (Ampcoloy 940) to improve the heat conductivity of the mould, Ni-Cu alloy (Monel 400) to reduce a thermal stress, injection tool steel (P21), respectively. Through the three-dimensional transient heat transfer analysis and the thermal stress analysis, the effects of the geometrical arrangement of each material on the cooling characteristics and the thermal stress distribution were examined. From the results of the analyses, a proper design of the thermal conductive mould was obtained.

• 한국표면공학회지
• /
• 제41권1호
• /
• pp.33-37
• /
• 2008

Polycarbonate has a high transmittance to light, low specific gravity, flexibility and cost-effectiveness that extends the application field of the polymer to bio-engineering, optics, electronic parts, etc. Moreover, electro plating of metallic film on PC could endow the parts the electromagnetic interference shielding capability. However, poor adhesion of copper on PC limited the wide usage in the industry. In this work, a composite(PC/ABS) and MmSH(Momentary mold Surface Heating) injection process were used to improve the plating characteristics; plating thickness, gloss and adhesion. Also plasma treatment and chemical treatment were employed for improving adhesion. Plating characteristics on PC/ABS were better than those on PC due to the anchoring effect of butadiene. MmSH injection process could ameliorate the gloss and coating adhesion. Also plating thickness and adhesion of PC and PC/ABS were increased by plasma treatment.

• Journal of Information Display
• /
• 제4권1호
• /
• pp.29-33
• /
• 2003

We have investigated the effects of hole-injection buffer layer in organic light-emitting diodes using copper phthalocyanine (CuPc), poly(vinylcarbazole)(PVK), and Poly(3,4-ethylene dioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) in a device structure of $ITO/bufferr/TPD/Alq_3/Al$. Polymer PVK and PEDOT:PSS buffer layer were produced using the spin casting method where as the CuPc layer was produced using thermal evaporation. Current-voltage characteristics, luminance-voltage characteristics and efficiency of device were measured at room temperature at various a thickness of the buffer layer. We observed an improvement in the external quantum efficiency by a factor of two, four, and two and half when the CuPc, PVK, and PEDOT:PSS buffer layer were used, respectively. The enhancement of the efficiency is assumed to be attributed to the improved balance of holes and elelctrons resulting from the use of hole-injection buffer layer. The CuPc and PEDOT:PSS layer function as a hole-injection supporter and the PVK layer as a hole-blocking one.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.740-744
• /
• 1995

For the fabrication of a multi-pole anisotropic Sr-ferrite magnet by powder injection molding, it is important to control effectively the alignment of magnetic powders during the injection molding process. The effect of the fluidity of powder/binder mixture on the powder alignment was studied with changing the particle sizes and the volume fraction of Sr-ferrite magnetic powders. The critical volume fraction of Sr-ferrite powders increases from 58 vol.% to 64 vol.% as the mean powder size increases from $0.8\;\mu\textrm{m}$ to $1.2\;\mu\textrm{m}$. A Sr-ferrite powder alignment greater than 80 % is achieved at the conditions of an apparent viscosity lower than 1000 poise at $1600\;sec^{-1}$ shear rate, an applied magnetic field higher than 4 kOe, and a powder volume fraction 8 vol.% lower than the critical fraction. The powder alignment obtained during the injection molding process is not much affected by the subsequent processes of debinding and sintering, showing the magnetic properties of 3.8 kG of remanent flux density and 3.37 kOe of intrinsic coercivity.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.215-222
• /
• 2023

3Y-TZP (3 mol% yttria-stabilized tetragonal zirconia polycrystals, 3Y-TZP) ceramics are emerging as dental implant materials due to their superior optical and mechanical properties as well as excellent biophysical properties, in spite of low bioactivity. In this study, we investigated to sintered properties and microstructural defects of dental zirconia implants fabricated by ceramic injection molding and post-HIP (Hot isostatic pressing) processing and analyzed the processing parameters related with the obtainment of its high sinterd density. Sintered and microstructural parameters, i.e, apparent density, grain size and phase composition of zirconia implants fabricated by injection molding were dependent on the fixtute size and implant type. Maximum sintered density of 99.2% and minimum grain size of 0.3-0.4 ㎛ were obtained from large-scaled 2-body sample. In 1-body ceramic implant, high sintered density of 99.5% was obtained, but it had a little monoclinic phase and wide grain size distribution.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.41-42
• /
• 2006

Small powder size is very useful in achieving detailed structures. STS 316 nanopowders with an average diameter of 100 nm and $5{\mu}m$ were utilized to produce feedstock. The mixing behavior of the feedstock indicated that the nanoparticle feedstock produced the highest mixing torque at various powder loading compared to the micropowder feedstock. The nanoparticles feedstocks showed that elastic properties are dominant in flow behavior and high viscosity. Conversely the micropowders feedstocks, viscous properties are dominant in flow behavior and less viscosity, nanopowders feedstock perform lower flow activation energy than feedstock with bigger particles.

• 소성∙가공
• /
• 제19권3호
• /
• pp.145-151
• /
• 2010

In case of thin-wall two-color injection molding, flashing often occurs when molten polymer flows into small gap at the parting line in mold with high pressure or under the unbalanced clamping force condition. In this study, flashing was examined in the production of thin-wall notebook case with large area when the rapid heat cycle molding (RHCM) technology was applied to the two-color injection molding. The effects of the RHCM technology on the part properties and weld-lines were compared with conventional injection molding. The flashing caused by the clamping device of the two-color injection molding machine was examined and compared by experiments and CAE analyses.

• 소성∙가공
• /
• 제15권1호
• /
• pp.76-81
• /
• 2006

In this study, warpage characteristics of mobile phone cover through injection molding process were investigated using design of experiments in injection molding process. Warpage in plastic injection molding has a significant effect on quality of product. Effects of injection time, packing pressure, packing time, mold temperature and melt temperature on the warpage of mobile phone cover were considered by numerical analysis and experiment with Taguchi method. The degree of warpage for the injection molded part was measured by using three dimensional coordinate measurement machine. It was shown that temperature control factor has more significant effect on the warpage of mobile phone cover than pressure control factor.

• 대한후두음성언어의학회지
• /
• 제26권1호
• /
• pp.46-50
• /
• 2015

Background and Objectives:Laryngeal hyperkinetic movements of stuttering patients is similar to that of adductor spasmodic dysphonia. There has been studies on implementing botulinium toxin injections to treat stuttering. However, the opinions on the bouolinium toxin injection's effects on stuttering patients vary. In this study authors aim to figure out when the botulinium toxin injection improves stuttering patients. Materials and Methods:Stuttering patients who could receive botulinium toxin injection participated in this study. Age differences, gender differences, electroglottogrphic test, aerodynamic test in botulinium toxin injection treatment of stuttering were analyzed. Results:The botulinium toxin injection had statistically significant impact on patients who showed low mean air flow rate during aerodynamic study. Conclusion:The botulinium toxin injection could reduce stuttering of patients with low mean air flow rate in aerodynamic study.